INSTALLATION
Removal / installation · Vehicles built Oct 2006 – May 2009
Versions by build date: Oct 2006 – May 2009 from Jun 2009
| 1. INSTALL AFS ECU |
Install the AFS ECU with the bolt.

Connect the connector.
| 2. HEIGHT CONTROL SENSOR SIGNAL INITIALIZATION |
| 3. VEHICLE PREPARATION FOR HEADLIGHT AIM ADJUSTMENT |
Prepare the vehicle:
- Ensure that there is no damage or deformation to the body around the headlights.
- Fill the fuel tank.
- Make sure that the oil is filled to the specified level.
- Make sure that the coolant is filled to the specified level.
- Inflate the tires to the appropriate pressure.
- Unload the trunk and vehicle, ensuring that the spare tire, tools, and jack are in their original positions.
- Sit a person of average weight (75 kg, 165 lb) in the driver's seat.
- Vehicles with manually adjustable headlights should be adjusted to "0".
- Ensure that there is no damage or deformation to the body around the headlights.
| 4. PREPARATION FOR HEADLIGHT AIMING |
Prepare the vehicle:

- Place the vehicle in a location that is dark enough to clearly observe the cutoff line. The cutoff line is a distinct line, below which light from the headlights can be observed and above which it cannot.
- Place the vehicle at a 90° angle to the wall.
- Create a 25 m (82 ft) distance between the vehicle (headlight bulb center) and the wall.
- Make sure that the vehicle is on a level surface.
- Bounce the vehicle up and down to settle the suspension.
- NOTICE:
- A distance of 25 m (82 ft) between the vehicle (headlight bulb center) and the wall is necessary for proper aim adjustment. If sufficient space is not available, secure a distance of exactly 3 m (9.84 ft) to allow for checking and adjustment of headlight aim. (The size of the target zone will change with the distance, so follow the instructions in the illustration.)
- Place the vehicle in a location that is dark enough to clearly observe the cutoff line. The cutoff line is a distinct line, below which light from the headlights can be observed and above which it cannot.
Prepare a piece of thick white paper (approximately 2 m (6.6 ft) (height) x 4 m (13.1 ft) (width)) to use as a screen.
Draw a vertical line down the center of the screen (V line).
Set the screen as shown in the illustration.


- HINT:
- Stand the screen perpendicular to the ground.
- Align the V line on the screen with the center of the vehicle.
- Stand the screen perpendicular to the ground.
Draw base lines (H, V LH, and V RH lines) on the screen as shown in the illustration.

- HINT:
- The base lines differ for "low-beam inspection" and "high-beam inspection."
- Mark the headlight bulb center marks on the screen. If the center mark cannot be observed on the headlight, use the center of the headlight bulb or the manufacturer's name marked on the headlight as the center mark.
- The base lines differ for "low-beam inspection" and "high-beam inspection."
H Line (Headlight height):
Draw a horizontal line across the screen so that it passes through the center marks. The H line should be at the same height as the headlight bulb center marks of the low-beam headlights.V LH Line, V RH Line (Center mark position of left-hand (LH) and right-hand (RH) headlights):
Draw two vertical lines so that they intersect the H line at each center mark (aligned with the center of the low-beam headlight bulbs).
| 5. HEADLIGHT AIMING INSPECTION |
Cover the headlight or disconnect the connector of the headlight on the opposite side to prevent light from the headlight that is not being inspected from affecting the headlight aiming inspection.
- CAUTION:
- Do not disconnect the HID high voltage connector for the bulb when performing this aiming inspection.
- NOTICE:
- Do not keep the headlight covered for more than 3 minutes. The headlight lens is made of synthetic resin, which may melt or be damaged due to excessive heat.
- HINT:
- When checking the aim of the high-beam, cover the low-beam or disconnect the connector.
Start the engine.
Turn on the headlight and check if the cutoff line matches the preferred cutoff line in the following illustration.


- HINT:
- Since the low-beam light and the high-beam light on each side have separate reflectors, it is necessary to check and adjust the aim separately for both.
- If the alignment distance is 25 m (82 ft):
The low-beam cutoff line should be between 48 mm (1.88 in.) and 698 mm (27.48 in.) below the H line.
- If the alignment distance is 3 m (9.84 ft):
The low beam cutoff line should be between 6 mm (0.23 in.) and 84 mm (3.3 in.) below the H line.
- If the alignment distance is 25 m (82 ft):
The preferred low-beam cutoff line is 249 mm (9.8 in.) below the H line.
- If the alignment distance is 3 m (9.84 ft):
The preferred low-beam cutoff line is 30 mm (1.18 in.) below the H line.
- Since the low-beam light and the high-beam light on each side have separate reflectors, it is necessary to check and adjust the aim separately for both.
| 6. HEADLIGHT AIMING ADJUSTMENT |
Remove any covers necessary to access the headlight adjusters.

Adjust the aim vertically:
Adjust the aim of each headlight to the specified range by turning each aiming screw A with a screwdriver.
When adjusting the vertical axis, note the change in the horizontal axis for correction later.
- NOTICE:
- The final turn of the aiming screw should be made in the clockwise direction. If the screw is adjusted too far, loosen it and then retighten it, so that the final turn of the screw is in the clockwise direction.
- HINT:
- The low-beam light and the high-beam light are a unit. Adjusting the aim on the low-beam to the correct position should also result in the high-beam adjustment being correct.
- When adjusting the vertical axis of the headlight, the horizontal axis will also change. It is necessary to adjust the vertical position first, and then correct the horizontal position.
- If it is not possible to correctly adjust headlight aim, check bulb, headlight unit, and headlight unit reflector installation.
- The headlight aim moves up and to the left when turning the aiming screw clockwise, and it moves down and to the right when turning the aiming screw counterclockwise.
- Confirm the direction of rotation of the aiming screw by observing it while it is being adjusted. Due to the position of the screwdriver, the direction of rotation of the adjusting screw can be different than the direction of rotation of the screwdriver being used to adjust it.
- The low-beam light and the high-beam light are a unit. Adjusting the aim on the low-beam to the correct position should also result in the high-beam adjustment being correct.
Adjust the aim horizontally:

Adjust the aim of each headlight to the specified range by turning each aiming screw B with a screwdriver.- NOTICE:
- The final turn of the aiming screw should be made in the clockwise direction. If the screw is tightened excessively, loosen it and then retighten it, so that the final turn of the screw is in the clockwise direction.
- HINT:
- The low-beam light and the high-beam light are a unit. Adjusting the aim on the low-beam to the correct position should also result in the high-beam adjustment being correct.
- If it is not possible to correctly adjust headlight aim, check bulb, headlight unit, and headlight unit reflector installation.
- The low-beam light and the high-beam light are a unit. Adjusting the aim on the low-beam to the correct position should also result in the high-beam adjustment being correct.
Adjust the aim of the high beam to the specified range by turning each adjusting screw with a screwdriver.
- NOTICE:
- The final turn of the aiming screw should be made in the clockwise direction. If the screw is adjusted too far, loosen it and then retighten it, so that the final turn of the screw is in the clockwise direction.
- HINT:
- Confirm the direction of rotation of the aiming screw by observing it while it is being adjusted. Due to the position of the screwdriver, the direction of rotation of the adjusting screw can be different than the direction of rotation of the screwdriver being used to adjust it.
Install any covers that were removed to access the headlight adjusters.
