Fuel Injector Circuit
Circuit diagnosis · Vehicles built Oct 2006 – May 2009
Versions by build date: Oct 2006 – May 2009 from Jun 2009
DESCRIPTION
The fuel injectors are located on the intake manifold. They inject fuel into the cylinders based on the signals from the ECM.WIRING DIAGRAM




INSPECTION PROCEDURE
| 1. CHECK ECM (#10, #20, #30, #40, #50, #60 VOLTAGE) |
Disconnect the C58 (RHD) or C55 (LHD) ECM connector.

Turn the ignition switch on (IG).
Measure the voltage between the terminals.
- Standard voltage:
- RHD:
Tester Connection
Specified Condition
#10 (C58-45) - E01 (C58-22)
9 to 14 V
#20 (C58-85) - E01 (C58-22)
9 to 14 V
#30 (C58-44) - E01 (C58-22)
9 to 14 V
#40 (C58-84) - E01 (C58-22)
9 to 14 V
#50 (C58-43) - E01 (C58-22)
9 to 14 V
#60 (C58-83) - E01 (C58-22)
9 to 14 V
- LHD:
Tester Connection
Specified Condition
#10 (C55-45) - E01 (C55-22)
9 to 14 V
#20 (C55-85) - E01 (C55-22)
9 to 14 V
#30 (C55-44) - E01 (C55-22)
9 to 14 V
#40 (C55-84) - E01 (C55-22)
9 to 14 V
#50 (C55-43) - E01 (C55-22)
9 to 14 V
#60 (C55-83) - E01 (C55-22)
9 to 14 V
Reconnect the ECM connector.
|
|
||||
| NG | |
| 2. INSPECT INJECTOR ASSEMBLY |
Inspect the injector assembly (Click here).
|
|
||||
| OK | |
| 3. INSPECT IGNITION RELAY NO. 2 |
Remove the IG2 relay from the engine room R/B.

Measure the resistance between the terminals.
- Standard resistance:
Tester Connection
Specified Condition
3 - 5
10 kΩ or higher
3 - 5
Below 1 Ω
(Apply battery voltage between terminals 1 and 2)
Reinstall the IG2 relay.
|
|
||||
| OK | |
| 4. CHECK HARNESS AND CONNECTOR (ECM - INJECTOR) |
Disconnect the injector connector.

Disconnect the C58 (RHD) or C55 (LHD) ECM connector.
Measure the resistance between the terminals.
- Standard resistance:
- RHD:
Tester Connection
Specified Condition
#10 (C58-45) - C7-1
Below 1 Ω
#20 (C58-85) - C9-1
Below 1 Ω
#30 (C58-44) - C8-1
Below 1 Ω
#40 (C58-84) - C10-1
Below 1 Ω
#50 (C58-43) - C36-1
Below 1 Ω
#60 (C58-83) - C37-1
Below 1 Ω
#10 (C58-45) or C7-1 - Body ground
10 kΩ or higher
#20 (C58-85) or C9-1 - Body ground
10 kΩ or higher
#30 (C58-44) or C8-1 - Body ground
10 kΩ or higher
#40 (C58-84) or C10-1 - Body ground
10 kΩ or higher
#50 (C58-43) or C36-1 - Body ground
10 kΩ or higher
#60 (C58-83) or C37-1 - Body ground
10 kΩ or higher
- LHD:
Tester Connection
Specified Condition
#10 (C55-45) - C7-1
Below 1 Ω
#20 (C55-85) - C9-1
Below 1 Ω
#30 (C55-44) - C8-1
Below 1 Ω
#40 (C55-84) - C10-1
Below 1 Ω
#50 (C55-43) - C36-1
Below 1 Ω
#60 (C55-83) - C37-1
Below 1 Ω
#10 (C55-45) or C7-1 - Body ground
10 kΩ or higher
#20 (C55-85) or C9-1 - Body ground
10 kΩ or higher
#30 (C55-44) or C8-1 - Body ground
10 kΩ or higher
#40 (C55-84) or C10-1 - Body ground
10 kΩ or higher
#50 (C55-43) or C36-1 - Body ground
10 kΩ or higher
#60 (C55-83) or C37-1 - Body ground
10 kΩ or higher
Reconnect the injector connector.
Reconnect the ECM connector.
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (INJECTOR - IG2 RELAY) |
Remove the IG2 relay from the engine room relay block.

Disconnect the injector connectors.
Measure the resistance between the terminals.
- Standard resistance (check for open):
Tester Connection
Specified Condition
C7-2 - IG2 relay terminal 3
Below 1 Ω
C9-2 - IG2 relay terminal 3
Below 1 Ω
C8-2 - IG2 relay terminal 3
Below 1 Ω
C10-2 - IG2 relay terminal 3
Below 1 Ω
C36-2 - IG2 relay terminal 3
Below 1 Ω
C37-2 - IG2 relay terminal 3
Below 1 Ω
- Standard resistance (check for short):
Tester Connection
Specified Condition
C7-2 or IG2 relay terminal 3 - Body ground
10 kΩ or higher
C9-2 or IG2 relay terminal 3 - Body ground
10 kΩ or higher
C8-2 or IG2 relay terminal 3 - Body ground
10 kΩ or higher
C10-2 or IG2 relay terminal 3 - Body ground
10 kΩ or higher
C36-2 or IG2 relay terminal 3 - Body ground
10 kΩ or higher
C37-2 or IG2 relay terminal 3 - Body ground
10 kΩ or higher
Reinstall the IG2 relay.
Reconnect the injector connector.
|
|
||||
| OK | |
| 6. INSPECT FUSE (IG2 FUSE) |
Remove the IG2 fuse from the engine room relay block.

Measure the IG2 fuse resistance.
- Standard resistance:
- Below 1 Ω
Reinstall the IG2 fuse.
|
|
||||
| OK | |
| 7. INSPECT IGNITION RELAY NO. 2 (VOLTAGE) |
Remove the IG2 relay from the engine room relay block.

Measure the IG2 relay voltage.
- Standard voltage:
Tester Connection
Specified Condition
IG2 Relay terminal 5 - Body ground
9 to 14 V
Reinstall the IG2 relay.
|
|
||||
| OK | |
| 8. CHECK HARNESS AND CONNECTOR (IG2 RELAY - BODY GROUND) |
Remove the IG2 relay from the engine room R/B.

Measure the resistance between the terminals.
- Standard resistance:
Tester Connection
Specified Condition
IG2 relay terminal 2 - Body ground
Below 1 Ω
Reinstall the IG2 relay.
- Result:
Result
Proceed to
OK (without smart entry and start system)
A
OK (with smart entry and start system)
B
NG
C
|
|
||||
|
|
||||
| A | |
| 9. CHECK HARNESS AND CONNECTOR (IG2 RELAY - IGNITION SWITCH) |
Remove the IG2 relay from the engine room relay block.

Disconnect the E23 ignition switch connector.
Measure the resistance between the terminals.
- Standard resistance (check for open):
Tester Connection
Specified Condition
IG2 relay terminal 1 - IG2 (E23-6)
Below 1 Ω
- Standard resistance (check for short):
Tester Connection
Specified Condition
IG2 relay terminal 1 or IG2 (E23-6) - Body ground
10 kΩ or higher
Reinstall the IG2 relay.
Reconnect the ignition switch connector.
|
|
||||
| OK | |
| 10. INSPECT IGNITION SWITCH |
Disconnect the E23 ignition switch connector.

Measure the resistance between the terminals.
- Standard resistance:
Tester Connection
Ignition Switch Position
Specified Condition
All terminals
LOCK
10 kΩ or higher
2 - 4
ACC
Below 1 Ω
1 - 2 - 4, 5 - 6
ON
1 - 3 - 4, 5 - 6 - 7
START
Reconnect the ignition switch connector.
|
|
||||
| OK | ||
| ||
| 11. CHECK HARNESS AND CONNECTOR (IG2 RELAY - MAIN BODY ECU) |
Remove the IG2 relay from the engine room relay block.

Disconnect the E6 main body ECU connector.
Measure the resistance between the terminals.
- Standard resistance (check for open):
Tester Connection
Specified Condition
IG2 relay terminal 1 - IG2D (E6-11)
Below 1 Ω
- Standard resistance (check for short):
Tester Connection
Specified Condition
IG2 relay terminal 1 or IG2D (E6-11) - Body ground
10 kΩ or higher
Reinstall the IG2 relay.
Reconnect the main body ECU connector.
|
|
||||
| OK | ||
| ||
