2006-2011 Camry Aurion · Service Manual ENGINE

Fuel Injector Circuit

Circuit diagnosis · Vehicles built from Jun 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

The fuel injectors are located on the intake manifold. They inject fuel into the cylinders based on the signals from the ECM.

WIRING DIAGRAM

A138977E04
A149034E02

INSPECTION PROCEDURE


1. CHECK ECM (#10, #20, #30, #40, #50, #60 VOLTAGE)

  1. A139137E04
    Disconnect the C58 (RHD) or C55 (LHD) ECM connector.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage between the terminals.

    Standard voltage:
    RHD:
    Tester Connection
    Specified Condition
    #10 (C58-45) - E01 (C58-22)
    9 to 14 V
    #20 (C58-85) - E01 (C58-22)
    9 to 14 V
    #30 (C58-44) - E01 (C58-22)
    9 to 14 V
    #40 (C58-84) - E01 (C58-22)
    9 to 14 V
    #50 (C58-43) - E01 (C58-22)
    9 to 14 V
    #60 (C58-83) - E01 (C58-22)
    9 to 14 V
    LHD:
    Tester Connection
    Specified Condition
    #10 (C55-45) - E01 (C55-22)
    9 to 14 V
    #20 (C55-85) - E01 (C55-22)
    9 to 14 V
    #30 (C55-44) - E01 (C55-22)
    9 to 14 V
    #40 (C55-84) - E01 (C55-22)
    9 to 14 V
    #50 (C55-43) - E01 (C55-22)
    9 to 14 V
    #60 (C55-83) - E01 (C55-22)
    9 to 14 V

  1. Reconnect the ECM connector.



OK
CHECK FOR INTERMITTENT PROBLEMS
NG


2. INSPECT INJECTOR ASSEMBLY
  1. Inspect the injector assembly (Click here).



NG
REPLACE INJECTOR ASSEMBLY (Click here)
OK


3. INSPECT IGNITION RELAY NO. 2

  1. B016200E27
    Remove the IG2 relay from the engine room R/B.

  1. Measure the resistance between the terminals.

    Standard resistance:
    Tester Connection
    Specified Condition
    3 - 5
    10 kΩ or higher
    3 - 5
    Below 1 Ω
    (Apply battery voltage between terminals 1 and 2)

  1. Reinstall the IG2 relay.



NG
REPLACE IGNITION RELAY NO. 2
OK


4. CHECK HARNESS AND CONNECTOR (ECM - INJECTOR)

  1. A106388E13
    Disconnect the injector connector.

  1. Disconnect the C58 (RHD) or C55 (LHD) ECM connector.

  1. Measure the resistance between the terminals.

    Standard resistance:
    RHD:
    Tester Connection
    Specified Condition
    #10 (C58-45) - C7-1
    Below 1 Ω
    #20 (C58-85) - C9-1
    Below 1 Ω
    #30 (C58-44) - C8-1
    Below 1 Ω
    #40 (C58-84) - C10-1
    Below 1 Ω
    #50 (C58-43) - C36-1
    Below 1 Ω
    #60 (C58-83) - C37-1
    Below 1 Ω
    #10 (C58-45) or C7-1 - Body ground
    10 kΩ or higher
    #20 (C58-85) or C9-1 - Body ground
    10 kΩ or higher
    #30 (C58-44) or C8-1 - Body ground
    10 kΩ or higher
    #40 (C58-84) or C10-1 - Body ground
    10 kΩ or higher
    #50 (C58-43) or C36-1 - Body ground
    10 kΩ or higher
    #60 (C58-83) or C37-1 - Body ground
    10 kΩ or higher
    LHD:
    Tester Connection
    Specified Condition
    #10 (C55-45) - C7-1
    Below 1 Ω
    #20 (C55-85) - C9-1
    Below 1 Ω
    #30 (C55-44) - C8-1
    Below 1 Ω
    #40 (C55-84) - C10-1
    Below 1 Ω
    #50 (C55-43) - C36-1
    Below 1 Ω
    #60 (C55-83) - C37-1
    Below 1 Ω
    #10 (C55-45) or C7-1 - Body ground
    10 kΩ or higher
    #20 (C55-85) or C9-1 - Body ground
    10 kΩ or higher
    #30 (C55-44) or C8-1 - Body ground
    10 kΩ or higher
    #40 (C55-84) or C10-1 - Body ground
    10 kΩ or higher
    #50 (C55-43) or C36-1 - Body ground
    10 kΩ or higher
    #60 (C55-83) or C37-1 - Body ground
    10 kΩ or higher

  1. Reconnect the injector connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. CHECK HARNESS AND CONNECTOR (INJECTOR - IG2 RELAY)

  1. A143981E01
    Remove the IG2 relay from the engine room relay block.

  1. Disconnect the injector connectors.

  1. Measure the resistance between the terminals.

    Standard resistance (check for open):
    Tester Connection
    Specified Condition
    C7-2 - IG2 relay terminal 3
    Below 1 Ω
    C9-2 - IG2 relay terminal 3
    Below 1 Ω
    C8-2 - IG2 relay terminal 3
    Below 1 Ω
    C10-2 - IG2 relay terminal 3
    Below 1 Ω
    C36-2 - IG2 relay terminal 3
    Below 1 Ω
    C37-2 - IG2 relay terminal 3
    Below 1 Ω

    Standard resistance (check for short):
    Tester Connection
    Specified Condition
    C7-2 or IG2 relay terminal 3 - Body ground
    10 kΩ or higher
    C9-2 or IG2 relay terminal 3 - Body ground
    10 kΩ or higher
    C8-2 or IG2 relay terminal 3 - Body ground
    10 kΩ or higher
    C10-2 or IG2 relay terminal 3 - Body ground
    10 kΩ or higher
    C36-2 or IG2 relay terminal 3 - Body ground
    10 kΩ or higher
    C37-2 or IG2 relay terminal 3 - Body ground
    10 kΩ or higher

  1. Reinstall the IG2 relay.

  1. Reconnect the injector connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. INSPECT FUSE (IG2 FUSE)

  1. A143982E01
    Remove the IG2 fuse from the engine room relay block.

  1. Measure the IG2 fuse resistance.

    Standard resistance:
    Below 1 Ω

  1. Reinstall the IG2 fuse.



NG
REPLACE IG2 FUSE
OK


7. INSPECT IGNITION RELAY NO. 2 (VOLTAGE)

  1. A137039E05
    Remove the IG2 relay from the engine room relay block.

  1. Measure the IG2 relay voltage.

    Standard voltage:
    Tester Connection
    Specified Condition
    IG2 Relay terminal 5 - Body ground
    9 to 14 V

  1. Reinstall the IG2 relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (IG2 RELAY - BATTERY)
OK


8. CHECK HARNESS AND CONNECTOR (IG2 RELAY - BODY GROUND)

  1. A137039E04
    Remove the IG2 relay from the engine room R/B.

  1. Measure the resistance between the terminals.

    Standard resistance:
    Tester Connection
    Specified Condition
    IG2 relay terminal 2 - Body ground
    Below 1 Ω

  1. Reinstall the IG2 relay.

    Result:
    Result
    Proceed to
    OK (without smart entry and start system)
    A
    OK (with smart entry and start system)
    B
    NG
    C



B
Go to step 11

C
REPAIR OR REPLACE HARNESS OR CONNECTOR
A


9. CHECK HARNESS AND CONNECTOR (IG2 RELAY - IGNITION SWITCH)

  1. A143983E01
    Remove the IG2 relay from the engine room relay block.

  1. Disconnect the E23 ignition switch connector.

  1. Measure the resistance between the terminals.

    Standard resistance (check for open):
    Tester Connection
    Specified Condition
    IG2 relay terminal 1 - IG2 (E23-6)
    Below 1 Ω

    Standard resistance (check for short):
    Tester Connection
    Specified Condition
    IG2 relay terminal 1 or IG2 (E23-6) - Body ground
    10 kΩ or higher

  1. Reinstall the IG2 relay.

  1. Reconnect the ignition switch connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


10. INSPECT IGNITION SWITCH

  1. A056879E45
    Disconnect the E23 ignition switch connector.

  1. Measure the resistance between the terminals.

    Standard resistance:
    Tester Connection
    Ignition Switch Position
    Specified Condition
    All terminals
    LOCK
    10 kΩ or higher
    2 - 4
    ACC
    Below 1 Ω
    1 - 2 - 4, 5 - 6
    ON
    1 - 3 - 4, 5 - 6 - 7
    START

  1. Reconnect the ignition switch connector.



NG
REPLACE IGNITION SWITCH
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION SWITCH - BATTERY)

11. CHECK HARNESS AND CONNECTOR (IG2 RELAY - MAIN BODY ECU)

  1. A152049E01
    Remove the IG2 relay from the engine room relay block.

  1. Disconnect the E6 main body ECU connector.

  1. Measure the resistance between the terminals.

    Standard resistance (check for open):
    Tester Connection
    Specified Condition
    IG2 relay terminal 1 - IG2D (E6-11)
    Below 1 Ω

    Standard resistance (check for short):
    Tester Connection
    Specified Condition
    IG2 relay terminal 1 or IG2D (E6-11) - Body ground
    10 kΩ or higher

  1. Reinstall the IG2 relay.

  1. Reconnect the main body ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

GO TO SMART ENTRY AND START SYSTEM


← Fuel Injector Circuit (Oct 2006 – May 2009)Cranking Holding Function Circuit (Oct 2006 – May 2009) →