2006-2011 Camry Aurion · Service Manual BODY

Power Seat Motor Circuit

Circuit diagnosis · Vehicles built from Oct 2006

DESCRIPTION

When the power seat control switch is operated, a command signal is sent to the front power seat switch RH (position control ECU). The front power seat switch RH (position control ECU) then controls the appropriate seat motor as needed. This memory system does not use a seat position sensor. The seat position is detected by counting pulses that are output when the motor turns. If there is no pulse output from the motor, the motor will stop operating. The front power seat switch RH (position control ECU) is designed so that any malfunction of the seat memory system will not interfere with manual seat control.
If the front power seat switch RH (position control ECU) detects a low motor speed, abnormal activity, or sudden motor current fluctuation, the system will stop the motor. If the motor operates continuously for 120 seconds or more, the system will stop the motor until the switch is turned on again.

WIRING DIAGRAM

B111872E12

INSPECTION PROCEDURE


1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER

  1. E138501E01
    Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Perform the ACTIVE TEST by following the directions on the tester screen.

    Driver Seat: 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Reclining
    Seat reclining operation
    FRONT / REAR
    -
    F Vertical
    Seat front vertical operation
    UP / DOWN
    -
    Lifter
    Seat lifer operation
    UP / DOWN
    -
    Slide
    Seat sliding operation
    FRONT / REAR
    -

    OK:
    Each power seat motor operates.



NG
Go to step 2
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

2. INSPECT POWER SEAT MOTOR ASSEMBLY
  1. Inspect the power seat motor (Click here).

    OK:
    The power seat motor operates.



NG
REPLACE POWER SEAT MOTOR ASSEMBLY
OK


3. CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH RH - POWER SEAT MOTOR ASSEMBLY)

  1. B128715E10
    Disconnect the front power seat switch RH (position control ECU) connector and power seat motor connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    T20-2 (SLD+) - T1-2
    Always
    Below 1 Ω
    T20-3 (SLD-) - T1-1
    Always
    Below 1 Ω
    T20-4 (FRV-) - T2-1
    Always
    Below 1 Ω
    T20-6 (FRV+) - T2-2
    Always
    Below 1 Ω
    T20-7 (LFT+) - T4-1
    Always
    Below 1 Ω
    T20-9 (LFT-) - T4-2
    Always
    Below 1 Ω
    T20-8 (RCL+) - j1-2
    Always
    Below 1 Ω
    T20-10 (RCL-) - j1-1
    Always
    Below 1 Ω
    T20-2 (SLD+) - Body ground
    Always
    10 kΩ or higher
    T20-3 (SLD-) - Body ground
    Always
    10 kΩ or higher
    T20-4 (FRV-) - Body ground
    Always
    10 kΩ or higher
    T20-6 (FRV+) - Body ground
    Always
    10 kΩ or higher
    T20-7 (LFT+) - Body ground
    Always
    10 kΩ or higher
    T20-9 (LFT-) - Body ground
    Always
    10 kΩ or higher
    T20-8 (RCL+) - Body ground
    Always
    10 kΩ or higher
    T20-10 (RCL-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE


← DATA LIST / ACTIVE TEST (from Oct 2006)Memory Switch Circuit (Oct 2006 – May 2009) →