2006-2011 Camry Aurion · Service Manual BODY ELECTRICAL

Microphone Circuit between Microphone and Navigation Receiver Assembly

Circuit diagnosis · Vehicles built from Jun 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

This circuit sends a microphone signal from the telephone microphone assembly to the navigation receiver assembly.
It also supplies power from the navigation receiver assembly to the telephone microphone assembly.

WIRING DIAGRAM

E185300E07

INSPECTION PROCEDURE


1. INSPECT NAVIGATION RECEIVER ASSEMBLY

  1. E176579E10
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    F12-17 (MACC) - Body ground
    Ignition switch on (ACC)
    4 to 6 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F12-18 (SGND) - Body ground
    Always
    Below 1 Ω
    F12-20 (MIC-) - Body ground
    Always
    Below 1 Ω

    Result:
    Result
    Proceed to
    OK
    A
    NG
    (for 2GR-FE RHD)
    B
    NG
    (except 2GR-FE RHD)
    C

    Text in Illustration 
    *1
    Component with harness connected
    (Navigation Receiver Assembly)



B
REPLACE NAVIGATION RECEIVER ASSEMBLY (for 2GR-FE RHD) (Click here)

C
REPLACE NAVIGATION RECEIVER ASSEMBLY (except 2GR-FE RHD) (Click here)
A


2. CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - TELEPHONE MICROPHONE ASSEMBLY)
  1. Disconnect the F12 navigation receiver assembly connector.

  1. Disconnect the Q15*1 or Q17*2 telephone microphone assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F12-5 (SNS2) - Q15-4 (SNS2)*1
    Always
    Below 1 Ω
    F12-17 (MACC) - Q15-1 (ACC)*1
    Always
    Below 1 Ω
    F12-19 (MIC+) - Q15-3 (MI1+)*1
    Always
    Below 1 Ω
    F12-20 (MIC-) - Q15-5 (MIC-)*1
    Always
    Below 1 Ω
    F12-5 (SNS2) - Q17-4 (SNS2)*2
    Always
    Below 1 Ω
    F12-17 (MACC) - Q17-1 (ACC)*2
    Always
    Below 1 Ω
    F12-19 (MIC+) - Q17-3 (MI1+)*2
    Always
    Below 1 Ω
    F12-20 (MIC-) - Q17-5 (MIC-)*2
    Always
    Below 1 Ω
    F12-5 (SNS2) - Body ground
    Always
    10 kΩ or higher
    F12-17 (MACC) - Body ground
    Always
    10 kΩ or higher
    F12-19 (MIC+) - Body ground
    Always
    10 kΩ or higher
    F12-20 (MIC-) - Body ground
    Always
    10 kΩ or higher
    F12-18 (SGND) - Body ground
    Always
    10 kΩ or higher

    1. *1: w/ Sliding Roof
    2. *2: w/o Sliding Roof



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. INSPECT TELEPHONE MICROPHONE ASSEMBLY

  1. E176581E08
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Q15-4 (SNS2) - Q15-5 (MIC-)*2
    Always
    Below 1 Ω
    Q17-4 (SNS2) - Q17-5 (MIC-)*3
    Always
    Below 1 Ω

    Text in Illustration 
    *1
    Component without harness connected
    (Telephone Microphone Assembly)
    1. *2: w/ Sliding Roof
    2. *3: w/o Sliding Roof



NG
REPLACE TELEPHONE MICROPHONE ASSEMBLY (Click here)
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)


← Microphone Circuit between Microphone and Navigation Receiver Assembly (Oct 2006 – May 2009)Stereo Component Amplifier Power Source Circuit (from Jun 2009) →