2006-2011 Camry Aurion · Service Manual BODY ELECTRICAL

Speed Signal Circuit

Circuit diagnosis · Vehicles built from Jun 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

The meter CPU receives vehicle speed signals from this circuit. The vehicle speed sensor detects the voltage that varies according to the vehicle speed. The skid control ECU supplies power to the vehicle speed sensor. The skid control ECU detects vehicle speed signals based on the pulses of the voltage. The skid control ECU transmits vehicle speed signals as pulses to the meter CPU. A voltage of 12 V is output from the combination meter assembly and then input to the skid control ECU. The signal is changed to a pulse signal at the transistor in the combination meter assembly.
A voltage of 12 V or 5 V is output from each ECU or relay and then input to the combination meter assembly.
Each ECU controls the respective system based on the pulse signal.

HINT:
This circuit is used for another system, and is not used for combination meter operation.


WIRING DIAGRAM


for 2AZ-FE
E192288E01

for 2GR-FE
E192360E01

INSPECTION PROCEDURE


1. SYSTEM CHECK
  1. Confirm the engine model.

    Result:
    Result
    Proceed to
    2AZ-FE
    A
    2GR-FE
    B



B
Go to step 10
A


2. INSPECT COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)

  1. E136594E01
    Check the waveform.
    1. Remove the combination meter assembly with connector still connected.

    2. Connect the oscilloscope to the terminals F1-11 (+S) and body ground.

    3. Turn the ignition switch on (IG).

    4. Turn the wheel slowly.

    5. Check the signal waveform according to the condition(s) in the table below.

      Item
      Condition
      Tool setting
      5 V/DIV., 20 ms./DIV.
      Vehicle condition
      Driving at approx. 20 km/h (12 mph)

      OK:
      The waveform is displayed as shown in the illustration.

      HINT:
      As the vehicle speed increases, the cycle of the waveform narrows.



NG
Go to step 3
OK

RETURN TO THE ORIGINAL INSPECTION FOR OTHER SYSTEM

3. INSPECT ECU TERMINAL VOLTAGE (INPUT VOLTAGE)

  1. E134491E03
    Remove the F1 connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    F1-11 (+S) - Body ground
    Turn the ignition switch on (IG)
    4.5 to 14 V

    HINT:
    If any of the ECUs specified in the wiring diagram supplied power to the combination meter, the combination meter will output a waveform.



NG
Go to step 6
OK


4. INSPECT COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE)

  1. E136601E01
    Remove the A25 (*1)/A26 (*2) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    A25-23 (SP1) (*1) - Body ground
    Turn the ignition switch on (IG)
    10 to 14 V
    A26-33 (SP1) (*2) - Body ground
    Turn the ignition switch on (IG)
    10 to 14 V

    *1: without VSC*2: with VSC



NG
Go to step 9
OK


5. INSPECT SKID CONTROL ECU (INPUT WAVEFORM)

  1. E136594E01
    Check the waveform.
    1. Reconnect the A25 (*1)/A26 (*2) connector.

    2. Remove the combination meter assembly with connector still connected.

    3. Connect the oscilloscope to the terminals F1-10 (SI) and body ground.

    4. Turn the ignition switch on (IG).

    5. Turn the wheel slowly.

    6. Check the signal waveform according to the condition(s) in the table below.

      Item
      Condition
      Tool setting
      5 V/DIV., 20 ms./DIV.
      Vehicle condition
      Driving at approx. 20 km/h (12 mph)
      *1: without VSC*2: with VSC

      OK:
      The waveform is displayed as shown in the illustration.

      HINT:
      As the vehicle speed increases, the cycle of the waveform narrows.



NG
REPLACE SKID CONTROL ECU
OK

REPLACE COMBINATION METER ASSEMBLY

6. CHECK HARNESS AND CONNECTOR (COMBINATION METER - NO. 3 JUNCTION BLOCK)

  1. Disconnect the A No. 3 junction block connector.E136595E01

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    F1-11 (+S) - 3P-3
    Always
    Below 1 Ω
    F1-11 (+S) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7. CHECK HARNESS AND CONNECTOR (NO. 3 JUNCTION BLOCK)

  1. Inspect for a short in the circuit that connected the No. 3 junction block shown in the wiring diagram.

    HINT:
    If voltage is not present, the circuit (ECU) was possibly the malfunctioning circuit. This is the circuit that will be diagnosed by following the A step that follows.

    1. Disconnect the B and C No. 3 junction block connectors.E136576E14

    2. Measure the voltage according to the value(s) in the table below.

      Standard voltage:
      Tester Connection
      Condition
      Specified Condition
      3B-10 - Body ground
      Turn the ignition switch on (IG)
      4.5 to 14 V
      3J-9 (*1) - Body ground
      Turn the ignition switch on (IG)
      4.5 to 14 V
      3M-10 (*2) - Body ground
      Turn the ignition switch on (IG)
      4.5 to 14 V

      *1: with Auto Wiper System*2: with Smart Entry and Start System

    3. Reconnect the B and C No. 3 junction block connector.

    4. Disconnect the A No. 3 junction block connector.E136575E14

    5. Measure the voltage according to the value(s) in the table below.

      Standard voltage:
      Tester Connection
      Condition
      Specified Condition
      3T-9 (*3), (*4) - Body ground
      Turn the ignition switch on (IG)
      4.5 to 14 V
      3T-10 (*5) - Body ground
      Turn the ignition switch on (IG)
      4.5 to 14 V

      *3: with Navigation System*4: for 2 DIN Model without Navigation System*5: for RHD

      Result:
      Result
      Proceed to
      Voltage is not present in one circuit.
      A
      Voltage is present in all the circuit.
      B



B
REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 3 JUNCTION BLOCK)
A


8. CHECK HARNESS AND CONNECTOR (NO. 3 JUNCTION BLOCK - MALFUNCTIONING CIRCUIT)

  1. Disconnect the ECU connector that is possibly the malfunctioning.E192369E01

  1. Measure the resistance according to the value(s) in the table below.

    1. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      F8-3 (SPD) (*1) - Body ground
      Always
      10 kΩ or higher
      F13-3 (SPD) (*2) - Body ground
      Always
      10 kΩ or higher
      E26-19 (SPD) (*3) - Body ground
      Always
      10 kΩ or higher
      F3-17 (SPD) (*4) - Body ground
      Always
      10 kΩ or higher
      O30-3 (SPD) (*5) - Body ground
      Always
      10 kΩ or higher

      *1: for 2 DIN model without Navigation System*2: with Navigation System*3: with Auto Wiper System*4: for RHD*5: without Corner Sensor

      HINT:
      If an inspected wire harness is connected to another junction connector or junction block, measure the voltage and check wire harness and connector in each circuit.

    2. E136593E01
      Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      A24-8 (SPD) - Body ground
      Always
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MALFUNCTIONING ECU

9. CHECK HARNESS AND CONNECTOR (COMBINATION METER - SKID CONTROL ECU)

  1. E136596E01
    Disconnect the F1 connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A25-23 (SP1) (*1) - F1-10 (SI)
    Always
    Below 1 Ω
    A25-23 (SP1) (*1) - Body ground
    Always
    10 kΩ or higher
    A26-33 (SP1) (*2) - F1-10 (SI)
    Always
    Below 1 Ω
    A26-33 (SP1) (*2) - Body ground
    Always
    10 kΩ or higher

    *1: without VSC*2: with VSC



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE COMBINATION METER ASSEMBLY

10. INSPECT COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)

  1. E136563E02
    Check the waveform.
    1. Remove the combination meter assembly with connector(s) still connected.

    2. Connect the oscilloscope to the terminals F2-12 (+S) and body ground.

    3. Turn the ignition switch on (IG).

    4. Turn the wheel slowly.

    5. Check the signal waveform according to the condition(s) in the table below.

      Item
      Condition
      Tool setting
      5 V/DIV., 20 ms./DIV.
      Vehicle condition
      Driving at approx. 20 km/h (12 mph)

      OK:
      The waveform is displayed as shown in the illustration.

      HINT:
      As the vehicle speed increases, the cycle of the waveform narrows.



NG
Go to step 11
OK

RETURN TO THE ORIGINAL INSPECTION FOR OTHER SYSTEM

11. INSPECT ECU TERMINAL VOLTAGE (INPUT VOLTAGE)

  1. E136564E01
    Remove the F2 connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    F2-12 (+S) - Body ground
    Turn the ignition switch on (IG)
    4.5 to 14 V

    HINT:
    If any of the ECUs specified in the wiring diagram supplied power to the combination meter, the combination meter will output a waveform.



NG
Go to step 14
OK


12. INSPECT COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE)

  1. E136601E01
    Remove the A25 (*1)/A26 (*2) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    A25-23 (SP1) (*1) - Body ground
    Turn the ignition switch on (IG)
    10 to 14 V
    A26-33 (SP1) (*2) - Body ground
    Turn the ignition switch on (IG)
    10 to 14 V

    *1: without VSC*2: with VSC



NG
Go to step 17
OK


13. INSPECT SKID CONTROL ECU (OUTPUT WAVEFORM)

  1. E136563E01
    Check the waveform.
    1. Reconnect the A25 (*1)/A26 (*2) connector.

    2. Remove the combination meter assembly with connector(s) still connected.

    3. Connect the oscilloscope to the terminals F2-14 (SI) and body ground.

    4. Turn the ignition switch on (IG).

    5. Turn the wheel slowly.

    6. Check the signal waveform according to the condition(s) in the table below.

      Item
      Condition
      Tool setting
      5 V/DIV., 20 ms./DIV.
      Vehicle condition
      Driving at approx. 20 km/h (12 mph)

      OK:
      The waveform is displayed as shown in the illustration.

      HINT:
      As the vehicle speed increases, the cycle of the waveform narrows.



NG
REPLACE SKID CONTROL ECU
OK

REPLACE COMBINATION METER ASSEMBLY

14. CHECK HARNESS AND CONNECTOR (COMBINATION METER - NO. 3 JUNCTION BLOCK)

  1. Disconnect the A No. 3 junction block connector.E136551E03

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    F2-12 (+S) - 3P-3
    Always
    Below 1 Ω
    F2-12 (+S) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


15. CHECK HARNESS AND CONNECTOR (NO. 3 JUNCTION BLOCK)

  1. Inspect for a short in the circuit that connected the No. 3 junction block shown in the wiring diagram.

    HINT:
    If voltage is not present, the circuit (ECU) was possibly the malfunctioning circuit. This is the circuit that will be diagnosed by following the A step that follows.

    1. Disconnect the B and C No. 3 junction block connectors.E136576E13

    2. Measure the voltage according to the value(s) in the table below.

      Standard voltage:
      Tester Connection
      Condition
      Specified Condition
      3B-10 - Body ground
      Turn the ignition switch on (IG)
      4.5 to 14 V
      3J-9 (*1) - Body ground
      Turn the ignition switch on (IG)
      4.5 to 14 V
      3M-10 (*2) - Body ground
      Turn the ignition switch on (IG)
      4.5 to 14 V

      *1: with Auto Wiper System*2: with Smart Entry and Start System

    3. Reconnect the B and C No. 3 junction block connector.

    4. Disconnect the A No. 3 junction block connector.E136575E05

    5. Measure the voltage according to the value(s) in the table below.

      Standard voltage:
      Tester Connection
      Condition
      Specified Condition
      3T-9 (*3), (*4) - Body ground
      Turn the ignition switch on (IG)
      4.5 to 14 V
      3T-10 (*5) - Body ground
      Turn the ignition switch on (IG)
      4.5 to 14 V

      *3: for 2 DIN Model without Navigation System*4: with Navigation System*5: for RHD

      Result:
      Result
      Proceed to
      Voltage is not present in one circuit
      A
      Voltage is present in all the circuit.
      B



B
REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 3 JUNCTION BLOCK)
A


16. CHECK HARNESS AND CONNECTOR (NO. 3 JUNCTION BLOCK - MALFUNCTIONING CIRCUIT)

  1. Disconnect the ECU connector that is possibly the malfunctioning.E136590E05

  1. Measure the resistance according to the value(s) in the table below.

    1. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      F8-3 (SPD) (*1) - Body ground
      Always
      10 kΩ or higher
      F13-3 (SPD) (*2) - Body ground
      Always
      10 kΩ or higher
      E26-19 (SPD) (*3) - Body ground
      Always
      10 kΩ or higher
      E8-9 (SPD) (*4) - Body ground
      Always
      10 kΩ or higher
      F3-9 (SPD) (*5) - Body ground
      Always
      10 kΩ or higher

      *1: for 2 DIN Model without Navigation System*2: with Navigation System*3: with Auto Wiper System*4: with Smart Entry and Start System*5: for RHD

      HINT:
      If an inspected wire harness is connected to another junction connector or junction block, measure the voltage and check wire harness and connector in each circuit.

    2. Measure the resistance according to the value(s) in the table below.E136591E02

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      A24-8 (*5) (SPD) - Body ground
      Always
      10 kΩ or higher
      A55-8 (SPD) (*6)- Body ground
      Always
      10 kΩ or higher
      A20-16 (*7) (SPDR) - Body ground
      Always
      10 kΩ or higher
      C56-3 (SPD1) - Body ground
      Always
      10 kΩ or higher

      *5: for RHD*6: for LHD*7: with Automatic Headlight Beam Level Control without AFS



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MALFUNCTIONING ECU

17. CHECK HARNESS AND CONNECTOR (COMBINATION METER - SKID CONTROL ECU)

  1. E136602E01
    Disconnect the F2 connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A25-23 (SP1) (*1) - F2-14 (SI)
    Always
    Below 1 Ω
    A25-23 (SP1) (*1) - Body ground
    Always
    10 kΩ or higher
    A26-33 (SP1) (*2) - F2-14 (SI)
    Always
    Below 1 Ω
    A26-33 (SP1) (*2) - Body ground
    Always
    10 kΩ or higher

    *1: without VSC*2: with VSC



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE COMBINATION METER ASSEMBLY


← Speed Signal Circuit (Oct 2006 – May 2009)COMPONENTS (Jun 2006 – Sep 2006) →