2006-2011 Camry Aurion · Service Manual COMMUNICATION SYSTEM

TERMINALS OF ECU

System information · Vehicles built from Jun 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009


CHECK MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
  1. Disconnect the E6*, E7* and E8* main body ECU connectors.

    HINT:
    *: Models with Smart Entry and Start System

  2. Disconnect the ID*, IF* and IM* instrument panel junction block assembly connectors.

    HINT:
    *: Models without Smart Entry and Start System

    B178893E01

  3. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E7-6 (AM1) - Body ground*1
    L - Body ground
    Battery power supply
    Always
    11 to 14 V
    E6-1 (AM2) - Body ground*1
    L - Body ground
    Battery power supply
    Always
    11 to 14 V
    ID-10 (BECU) - Body ground*2
    BE - Body ground
    Battery power supply
    Always
    11 to 14 V
    E8-1 (GND3) - Body ground*1
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    IF-10 (GND1) - Body ground*2
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    IM-9 (GND2) - Body ground*2
    W-B - Body ground
    Ground
    Always
    Below 1 Ω

    HINT:
    1. *1: Models with Smart Entry and Start System
    2. *2: Models without Smart Entry and Start System

    If the result is not as specified, there may be a malfunction on the wire harness side.

  4. Reconnect the E6*, E7* and E8* main body ECU connectors.

    HINT:
    *: Models with Smart Entry and Start System

  5. Reconnect the ID*, IF* and IM* instrument panel junction block assembly connectors.

    HINT:
    *: Models without Smart Entry and Start System

  6. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E8-10 (LIN2) - IF-10 (GND1)
    P - W-B
    LIN Communication line
    Ignition switch on (IG)
    Pulse generation
    If the result is not as specified, the main body ECU (Instrument panel junction block assembly) may have a malfunction.


CHECK POWER WINDOW REGULATOR MOTOR (DRIVER SIDE)

  1. Disconnect the I5*1 or H10*2 motor connector.

    HINT:
    1. *1: for LHD
    2. *2: for RHD

    B158006E31

  2. Measure the voltage and resistance according to the value(s) in the table below.

    for LHD 
    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I5-2 (B) - I5-1 (E)
    W - W-B
    Battery power supply
    Always
    11 to 14 V
    I5-1 (E) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    for RHD 
    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    H10-2 (B) - H10-1 (E)
    W - W-B
    Battery power supply
    Always
    11 to 14 V
    H10-1 (E) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the I5*1 or H10*2 motor connector.

    HINT:
    1. *1: for LHD
    2. *2: for RHD

  4. Measure the voltage according to the value(s) in the table below.

    for LHD 
    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I5-9 (LIN) - I5-1 (E)
    P - W-B
    LIN Communication line
    Ignition switch on (IG)
    Pulse generation
    for RHD 
    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    H10-9 (LIN) - H10-1 (E)
    P - W-B
    LIN Communication line
    Ignition switch on (IG)
    Pulse generation
    If the result is not as specified, the motor may be malfunctioning.


CHECK SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR)*

HINT:
*: Models with Sliding Roof System

  1. Disconnect the Q12 ECU connector.
    B160074E08

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    Q12-1 (B) - Q12-2 (E)
    B - W-B
    Battery power supply
    Always
    11 to 14 V
    Q12-2 (E) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the Q12 ECU connector.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    Q12-4 (MPX1) - Q12-2 (E)
    P - W-B
    LIN Communication line
    Ignition switch on (IG)
    Pulse generation
    If the result is not as specified, the motor may be malfunctioning.

← TERMINALS OF ECU (Oct 2006 – May 2009)DIAGNOSIS SYSTEM (from Jun 2006) →