2006-2011 Camry Aurion · Service Manual ENGINE

P0617 Starter Relay Circuit High

Diagnostic trouble codes · Vehicles built from Jun 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

While the engine is being cranked, the positive battery voltage is applied to terminal STA of the ECM.
If the ECM detects the Starter Control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and sets the DTC.
This monitor runs when the vehicle is driven at 20 km/h (12.4 mph) for over 20 seconds.
DTC No.
DTC Detection Condition
Trouble Area
P0617
When conditions (a), (b) and (c) are met, positive (+B) battery voltage 10.5 V or more applied to ECM for 20 seconds
(1 trip detection logic):
(a) Vehicle speed more than 20 km/h (12.4 mph)
(b) Engine speed more than 1,000 rpm
(c) STA signal ON
  1. Park/Neutral Position (PNP) switch
  2. Starter relay circuit
  3. Cranking holding function circuit (With smart entry and system)
  4. Ignition switch (Without smart start system)
  5. ECM

WIRING DIAGRAM

A138980E03
A149031E02

INSPECTION PROCEDURE

HINT:
  1. The following troubleshooting flowchart is based on the premise that the engine is cranked normally. If the engine does not crank, proceed to the problem symptoms table (Click here).
  2. Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction (Click here).


1. READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester on.

  1. Enter the following menus: Powertrain / Engine / Data List / Starter Signal.

  1. Check the value displayed on the tester when the ignition switch is turned on (IG) and the engine is started.

    OK:
    Switch Condition
    Ignition Switch on (IG)
    Engine Start
    Starter Signal
    OFF
    ON



OK
REPLACE ECM (Click here)
NG


2. INSPECT PARK / NEUTRAL POSITION SWITCH ASSEMBLY

  1. A107908E14
    Inspect the Park/Neutral Position (PNP) switch.
    1. Disconnect the C1 switch connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Gear Selector Lever Position
      Tester Connection
      Specified Condition
      P
      B (C1-4) - L (C1-9)
      Below 1 Ω
      N
      B (C1-4) - L (C1-9)
      Below 1 Ω

    3. Reconnect the PNP switch connector.

      Result:
      Result
      Proceed to
      OK (without smart entry and start system)
      A
      OK (with smart entry and start system)
      B
      NG (w/ smart entry and start system)
      C
      NG (w/o smart entry and start system)
      D



B
CHECK CRANKING HOLDING FUNCTION CIRCUIT (Click here)

C
REPLACE PARK/NEUTRAL POSITION SWITCH (THEN CHECK CRANKING HOLDING FUNCTION CIRCUIT) (Click here)

D
REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY (Click here)
A


3. INSPECT IGNITION SWITCH ASSEMBLY

  1. A135034E01
    Disconnect the E23 ignition switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Switch Condition
    Tester Connection
    Specified Condition
    LOCK
    ST1 (E23-3) - AM1 (E23-4)
    ST2 (E23-7) - AM2 (E23-5)
    10 kΩ or higher
    START
    ST1 (E23-3) - AM1 (E23-4)
    ST2 (E23-7) - AM2 (E23-5)
    Below 1 Ω

  1. Reconnect the ignition switch connector.



NG
REPAIR OR REPLACE IGNITION SWITCH ASSEMBLY
OK


4. READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester on.

  1. Enter the following menus: Powertrain / Engine / Data List / Starter Signal.

  1. Check the value displayed on the tester when the ignition switch is turned on (IG) and the ignition is started.

    OK:
    Switch Condition
    Ignition Switch on (IG)
    Engine Start
    Starter Signal
    OFF
    ON



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

SYSTEM IS OK


← P0617 Starter Relay Circuit High (Oct 2006 – May 2009)P0660 Intake Manifold Tuning Valve Control Circuit / Open (Bank 1) (Oct 2006 – May 2009) →