INSTALLATION
Removal / installation · Vehicles built Jun 2006 – Sep 2006
Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009
| 1. INSTALL SEAT POSITION SENSOR (for Power Seat) |
Check that the ignition switch is off.
Check that the negative battery (-) cable is disconnected.
- CAUTION:
- Wait for 90 seconds after disconnecting the cable to prevent airbag deployment.
Engage the pin and install the seat position sensor to the seat slide position sensor protector as shown in the illustration.

Using a 1.0 mm (0.039 in.) feeler gauge, temporarily install the seat position sensor.

- NOTICE:
- If the seat position sensor has been dropped, or there are any cracks, dents or other defects in the case or connector, replace the seat position sensor with a new one.
- When installing the seat position sensor, be careful that the SRS wiring does not interfere with other parts and that it is not pinched between other parts.
- If the seat position sensor has been dropped, or there are any cracks, dents or other defects in the case or connector, replace the seat position sensor with a new one.
- HINT:
- Be sure that the clearance between the seat position sensor and the seat rail is within 0.6 mm (0.024 in.) to 2.0 mm (0.079 in.).
Using a "TORX" socket (T30), tighten the "TORX" screw to install the seat position sensor.

- Torque:
- 8.0 N*m{ 82 kgf*cm , 71 in.*lbf }
Make sure that the clearance between the seat position sensor and the seat rail is within 0.6 mm (0.024 in.) to 2.0 mm (0.079 in.).
Check that there is no looseness in the installation parts of the seat position sensor.
Connect the connector.
| 2. INSTALL SEAT POSITION SENSOR (for Manual Seat) |
Check that the ignition switch is off.
Check that the negative battery (-) cable is disconnected.
- CAUTION:
- Wait for 90 seconds after disconnecting the cable to prevent airbag deployment.
Engage the pin and install the seat position sensor to the seat slide position sensor protector as shown in the illustration.

Using a 1.0 mm (0.039 in.) feeler gauge, temporarily install the seat position sensor.

- NOTICE:
- If the seat position sensor has been dropped, or there are any cracks, dents or other defects in the case or connector, replace the seat position sensor with a new one.
- When installing the seat position sensor, be careful that the SRS wiring does not interfere with other parts and that it is not pinched between other parts.
- If the seat position sensor has been dropped, or there are any cracks, dents or other defects in the case or connector, replace the seat position sensor with a new one.
- HINT:
- Be sure that the clearance between the seat position sensor and the seat rail is within 0.6 mm (0.024 in.) to 2.0 mm (0.079 in.).
Using a "TORX" socket (T30), tighten the "TORX" screw to install the seat position sensor.

- Torque:
- 8.0 N*m{ 82 kgf*cm , 71 in.*lbf }
Make sure that the clearance between the seat position sensor and the seat rail is within 0.6 mm (0.024 in.) to 2.0 mm (0.079 in.).
Check that there is no looseness in the installation parts of the seat position sensor.
Connect the connector.
| 3. INSTALL FRONT SEAT CUSHION SHIELD (for Manual Seat) |
Connect the connector. (w/ lumber support)
Engage the 2 claws.

Install the front seat cushion shield with the 2 screws.
Install the 2 rubber bands on the backside of the front seatback board sub-assembly.

| 4. INSTALL RECLINING ADJUSTER RELEASE HANDLE (for Manual Seat) |
Engage the claw to install the reclining adjuster release handle.

| 5. INSTALL VERTICAL ADJUSTING HANDLE (for Manual Seat) |
Install the No. 2 vertical adjusting handle with the 2 screws.

| 6. INSTALL VERTICAL ADJUSTER COVER LH (for Manual Seat) |
Engage the 2 claws to install the vertical adjuster cover.

| 7. INSTALL FRONT SEAT ASSEMBLY LH (for Power Seat) |
Place the seat in the cabin.
Connect the connectors under the seat.
Connect the cable to the negative (-) battery terminal.
Move the front seat assembly to the rearmost position by operating the slide and vertical power seat switch knob.
Temporarily install the front side of the front seat assembly with the 2 bolts.

Move the front seat assembly fully forward by operating the slide and vertical power seat switch knob.
Temporarily install the rear side of the front seat assembly with the 2 bolts.

Move the front seat assembly to the rearmost position by operating the slide and vertical power seat switch knob.
Fully tighten the 2 bolts on the front side of the front seat assembly in the order of the inner side bolt and then the outer side bolt.
- Torque:
- 37 N*m{ 377 kgf*cm , 27 ft.*lbf }
Move the front seat assembly fully forward by operating the slide and vertical power seat switch knob.
Fully tighten the 2 bolts on the rear side of the front seat assembly in the order of the inner side bolt and then the outer side bolt.
- Torque:
- 37 N*m{ 377 kgf*cm , 27 ft.*lbf }
| 8. INSTALL INNER SEAT TRACK BRACKET COVER LH (for Power Seat) |
Slide the inner seat track bracket cover along the seat rail toward the front of the vehicle. Engage claw A to the seat rail.

Push the inner seat track bracket cover to engage claw B.
| 9. INSTALL OUTER SEAT TRACK BRACKET COVER LH (for Power Seat) |
Slide the outer seat track bracket cover along the seat rail toward the front of the vehicle. Engage claw A to the seat rail.

Push the seat track cover to engage claw B.
| 10. INSTALL FRONT SEAT HEADREST ASSEMBLY (for Power Seat) |
| 11. INSTALL FRONT SEAT ASSEMBLY LH (for Manual Seat) |
Place the front seat assembly in the vehicle and align the adjuster pin with the hole on the vehicle side.
Connect the connector and clamp.
Move the front seat assembly to the rearmost position by operating the slide handle.
- NOTICE:
- Check that the seat is locked.
Temporarily install the front seat track bracket with the 2 bolts.

Move the front seat assembly fully forward by operating the slide handle.
- NOTICE:
- Check that the seat is locked.
Temporarily install the rear seat track bracket with the 2 bolts.

Move the front seat assembly to the rearmost position by operating the slide handle.
- NOTICE:
- Check that the seat is locked.
Fully tighten the 2 bolts on the front seat track bracket in the order of the inner side bolt and then the outer side bolt.
- Torque:
- 37 N*m{ 377 kgf*cm , 27 ft.*lbf }
Move the front seat assembly fully forward by operating the slide handle.
- NOTICE:
- Check that the seat is locked.
Fully tighten the 2 bolts on the rear seat track bracket in the order of the inner side bolt and then the outer side bolt.
- Torque:
- 37 N*m{ 377 kgf*cm , 27 ft.*lbf }
| 12. INSTALL INNER SEAT TRACK BRACKET COVER LH (for Manual Seat) |
Slide the inner seat track bracket cover along the seat rail toward the front of the vehicle. Engage claw A to the seat rail.

Push the inner seat track bracket cover inner to engage claw B.
| 13. INSTALL OUTER SEAT TRACK BRACKET COVER LH (for Manual Seat) |
Slide the outer seat track bracket cover along the seat rail toward the front of the vehicle. Engage claw A to the seat rail.

Push the outer seat track bracket cover to engage claw B.
| 14. INSTALL FRONT SEAT HEADREST ASSEMBLY (for Manual Seat) |
| 15. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (for Manual Seat) |
| 16. INSPECT FRONT SEAT ASSEMBLY (for Power Seat) |
Inspect the power seat operation.
| 17. INSPECT SLIDE ADJUSTER LOCK (for Manual Seat) |
| 18. INSPECT SRS WARNING LIGHT |
Inspect the SRS warning light (Click here).
