REMOVAL
Removal / installation · Vehicles built Oct 2006 – May 2009
Versions by build date: Oct 2006 – May 2009 from Jun 2009
| 1.
PRECAUTION |
 |
- CAUTION:
- Be sure to read "PRECAUTION" thoroughly before servicing (Click here).
| 2.
DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
 |
- CAUTION:
- Wait for 90 seconds after disconnecting the cable to prevent airbag deployment.
| 3.
REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Automatic Transaxle LHD)
|
 |
- Turn the shift lever knob counterclockwise and remove the shift lever knob sub-assembly.
| 4.
REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Automatic Transaxle RHD)
|
 |
- Turn the shift lever knob counterclockwise and remove the shift lever knob sub-assembly.
| 5.
REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transaxle)
|
 |
- Turn the shift lever knob counterclockwise and remove the shift lever knob sub-assembly.
| 6.
REMOVE NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH
|
 |
- Disengage the 2 clips and remove the No. 2 instrument cluster finish panel garnish.
| 7.
REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH
|
 |
- Disengage the 2 clips and remove the No. 1 instrument cluster finish panel garnish.
| 8.
REMOVE POSITION INDICATOR HOUSING ASSEMBLY (for Automatic Transaxle LHD)
|
 |
- Disengage the 6 claws and the 3 clips, and then remove the position indicator housing assembly.
| 9.
REMOVE POSITION INDICATOR HOUSING ASSEMBLY (for Automatic Transaxle RHD)
|
 |
- Open the lid of the upper console panel.
Apply protective tape to the area shown in the illustration.
- Using a moulding remover, disengage the 2 claws and the 5 clips, and then remove the position indicator housing assembly as shown in the illustration.
| 10.
REMOVE UPPER CONSOLE PANEL (for Manual Transaxle)
|
 |
- Open the lid of the upper console panel.
Apply protective tape to the area shown in the illustration.
- Using a moulding remover, disengage the 2 claws and the 5 clips, and then remove the upper console panel as shown in the illustration.
| 11.
REMOVE UPPER CONSOLE REAR PANEL SUB-ASSEMBLY (for Automatic Transaxle LHD)
|
 |
- Disengage the 3 claws and the 5 clips.
Disconnect the connector and remove the upper console rear panel sub-assembly.
| 12.
REMOVE UPPER CONSOLE REAR PANEL SUB-ASSEMBLY (for Automatic Transaxle RHD)
|
 |
- Disengage the 3 claws and the 5 clips, and remove the upper console rear panel sub-assembly.
| 13.
REMOVE UPPER CONSOLE REAR PANEL SUB-ASSEMBLY (for Manual Transaxle)
|
 |
- Disengage the 3 claws and the 5 clips, and remove the upper console rear panel sub-assembly.
| 14.
REMOVE LOWER INSTRUMENT CLUSTER FINISH PANEL CENTER SUB-ASSEMBLY
|
 |
- Remove the 2 screws <F>.
Disengage the 4 claws.
Disconnect each connector and remove the instrument cluster finish panel center sub-assembly.
- HINT:
- Set the shift lever in the D position.
| 15.
REMOVE FRONT DOOR SCUFF PLATE LH
|
 |
- Disengage the 7 claws and 3 clips, and remove the front door scuff plate LH.
| 16.
REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH
|
 |
- Remove the cowl side trim clip.
Disengage the 2 clips and remove the cowl side trim sub-assembly LH.
| 17.
REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL
|
 |
- Remove the bolt <A> and the screw <B>.
Disengage the 2 claws and the DLC3.
Disconnect the hood lock control cable assembly.
Disengage the claw and the 4 clips.
Remove the air hose, disconnect the connector, and then remove the lower No. 1 instrument panel finish panel.
| 18.
REMOVE FRONT DOOR SCUFF PLATE RH |
 |
- HINT:
- Use the same procedure for the RH and LH side (Click here).
| 19.
REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH |
 |
- HINT:
- Use the same procedure for the RH and LH side (Click here).
| 20.
REMOVE INSTRUMENT PANEL NO. 2 UNDER COVER SUB-ASSEMBLY
|
 |
- Disengage the 4 claws.
Disengage the 2 guides and remove the No. 2 under cover sub-assembly.
| 21.
REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY
|
 |
- Remove the bolt <A>.
Remove the 4 screws <B>.
Disengage the 3 claws and 3 clips, and then remove the lower instrument panel sub-assembly.
| 22.
REMOVE CONSOLE BOX POCKET
|
 |
Remove the console box pocket.
| 23.
REMOVE CONSOLE BOX CARPET
|
 |
- Remove the console box carpet.
| 24.
REMOVE CONSOLE BOX ASSEMBLY
|
 |
- Remove the 2 screws <F>.
- Disengage the clamp.
Remove the 2 bolts <G> and the console box assembly.
| 25.
REMOVE NO. 2 CONSOLE BOX INSERT FRONT
|
 |
- Remove the 3 screws <F>.
Disengage the clip and remove the No. 2 console box insert front.
| 26.
REMOVE NO. 1 CONSOLE BOX INSERT FRONT
|
 |
- Remove the 3 screws <F>.
Disengage the clip and remove the No. 1 console box insert front.
| 27.
REMOVE NO. 1 CONSOLE BOX DUCT
|
 |
- Remove the clip and No. 1 console box duct.
| 28.
REMOVE CENTER AIRBAG SENSOR ASSEMBLY |
 |
Turn back the carpet.
- Disconnect the holder (with connectors).
Remove the 3 bolts and center airbag sensor assembly.