2006-2011 Camry Aurion · Service Manual RESTRAINTS

REMOVAL

Removal / installation · Vehicles built from Jun 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009


1. PRECAUTION

CAUTION:
Be sure to read "PRECAUTION" thoroughly before servicing (Click here).


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait for 90 seconds after disconnecting the cable to prevent airbag deployment.


3. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Automatic Transaxle LHD)

  1. B226062
    Turn the shift lever knob counterclockwise and remove the shift lever knob sub-assembly.


4. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Automatic Transaxle RHD)

  1. B232854
    Turn the shift lever knob counterclockwise and remove the shift lever knob sub-assembly.


5. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transaxle)

  1. B232855
    Turn the shift lever knob counterclockwise and remove the shift lever knob sub-assembly.


6. REMOVE NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH

  1. B226063
    Disengage the 2 clips and remove the No. 2 instrument cluster finish panel garnish.


7. REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH

  1. B226064
    Disengage the 2 clips and remove the No. 1 instrument cluster finish panel garnish.


8. REMOVE POSITION INDICATOR HOUSING ASSEMBLY (for Automatic Transaxle LHD)

  1. B226065
    Disengage the 6 claws and the 3 clips, and then remove the position indicator housing assembly.


9. REMOVE POSITION INDICATOR HOUSING ASSEMBLY (for Automatic Transaxle RHD)

  1. B232856E01
    Open the lid of the upper console panel.

  1. Apply protective tape to the area shown in the illustration.

  1. B232857
    Using a moulding remover, disengage the 2 claws and the 5 clips, and then remove the position indicator housing assembly as shown in the illustration.


10. REMOVE UPPER CONSOLE PANEL (for Manual Transaxle)

  1. B137274E01
    Open the lid of the upper console panel.

  1. Apply protective tape to the area shown in the illustration.

  1. B137275
    Using a moulding remover, disengage the 2 claws and the 5 clips, and then remove the upper console panel as shown in the illustration.


11. REMOVE UPPER CONSOLE REAR PANEL SUB-ASSEMBLY (for Automatic Transaxle LHD)

  1. B226097
    Disengage the 3 claws and the 5 clips.

  1. Disconnect the connector and remove the upper console rear panel sub-assembly.


12. REMOVE UPPER CONSOLE REAR PANEL SUB-ASSEMBLY (for Automatic Transaxle RHD)

  1. B137277
    Disengage the 3 claws and the 5 clips, and remove the upper console rear panel sub-assembly.


13. REMOVE UPPER CONSOLE REAR PANEL SUB-ASSEMBLY (for Manual Transaxle)

  1. B137277
    Disengage the 3 claws and the 5 clips, and remove the upper console rear panel sub-assembly.


14. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY

  1. B133997E01
    Remove the 2 screws <F>.

  1. Disengage the 4 claws.

  1. Disconnect each connector and remove the upper console panel sub-assembly.

    HINT:
    Set the shift lever in the D position.


15. REMOVE FRONT DOOR SCUFF PLATE LH

  1. B132067
    Disengage the 7 claws and 3 clips, and remove the front door scuff plate LH.


16. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH

  1. B132116E01
    Remove the cowl side trim clip.

  1. Disengage the 2 clips and remove the cowl side trim sub-assembly LH.


17. REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL

  1. B147264E01
    Remove the bolt <A> and the screw <B>.

  1. Disengage the 2 claws and the DLC3.

  1. Disconnect the hood lock control cable assembly.

  1. Disengage the claw and the 4 clips.

  1. Remove the air hose, disconnect the connector, and then remove the lower No. 1 instrument panel finish panel.


18. REMOVE FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedure for the RH and LH side (Click here).


19. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:
Use the same procedure for the RH and LH side (Click here).


20. REMOVE INSTRUMENT PANEL NO. 2 UNDER COVER SUB-ASSEMBLY

  1. B133988E01
    Disengage the 4 claws.

  1. Disengage the 2 guides and remove the No. 2 under cover sub-assembly.


21. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY

  1. B133992E01
    Remove the bolt <A>.

  1. Remove the 4 screws <B>.

  1. Disengage the 3 claws and 3 clips, and then remove the lower instrument panel sub-assembly.


22. REMOVE CONSOLE BOX POCKET
  1. Remove the console box pocket.


23. REMOVE CONSOLE BOX CARPET

  1. B134004
    Remove the console box carpet.


24. REMOVE CONSOLE BOX ASSEMBLY

  1. B134002E01
    Remove the 2 screws <F>.

  1. B149935E03
    Disengage the clamp.

  1. Remove the 2 bolts <G> and the console box assembly.


25. REMOVE NO. 2 CONSOLE BOX INSERT FRONT

  1. B134005E01
    Remove the 3 screws <F>.

  1. Disengage the clip and remove the No. 2 console box insert front.


26. REMOVE NO. 1 CONSOLE BOX INSERT FRONT

  1. B134006E01
    Remove the 3 screws <F>.

  1. Disengage the clip and remove the No. 1 console box insert front.


27. REMOVE NO. 1 CONSOLE BOX DUCT

  1. C129716
    Remove the clip and No. 1 console box duct.


28. REMOVE CENTER AIRBAG SENSOR ASSEMBLY
  1. Turn back the carpet.

  1. C133884
    Disconnect the holder (with connectors).

  1. Remove the 3 bolts and center airbag sensor assembly.

← REMOVAL (Oct 2006 – May 2009)INSTALLATION (Oct 2006 – May 2009) →