Home › BODY › SEAT › FRONT SEAT ASSEMBLY (for 2GR-FE RHD Power Seat)
REASSEMBLY
Removal / installation · Vehicles built from Jun 2009
Versions by build date: Oct 2006 – May 2009 from Jun 2009
CAUTION:
Wear protective gloves. Sharp areas on the seat adjuster may injure your hands.
1.
INSTALL SEAT POSITION SENSOR (for Driver Seat)
Check that the ignition switch is off.
Check that the negative battery (-) cable is disconnected.
CAUTION:
Wait for 90 seconds after disconnecting the cable to prevent airbag deployment.
Engage the pin and install the seat position sensor to the seat slide position sensor protector as shown in the illustration.
Using a 1.0 mm (0.039 in.) feeler gauge, temporarily install the seat position sensor.
NOTICE:
If the seat position sensor has been dropped, or there are any cracks, dents or other defects in the case or connector, replace the seat position sensor with a new one.
When installing the seat position sensor, be careful that the SRS wiring does not interfere with other parts and that it is not pinched between other parts.
HINT:
Be sure that the clearance between the seat position sensor and the seat rail is within 0.6 mm (0.024 in.) to 2.0 mm (0.079 in.).
Using a "TORX" socket (T30), tighten the "TORX" screw to install the seat position sensor.
Torque:
8.0 N*m{
82 kgf*cm
, 71 in.*lbf
}
Make sure that the clearance between the seat position sensor and the seat rail is within 0.6 mm (0.024 in.) to 2.0 mm (0.079 in.).
Check that there is no looseness in the installation parts of the seat position sensor.
Connect the connector.
2.
INSTALL FRONT SEAT WIRE
Engage the each claw and each clamp and install the front seat wire.
3.
INSTALL FRONT SEPARATE TYPE SEATBACK SPRING ASSEMBLY
Install the front separate type seatback spring assembly with the 4 bolts.
Torque:
42 N*m{
428 kgf*cm
, 31 ft.*lbf
}
Connect the 2 clamps and connector.
4.
INSTALL FRONT LOWER SEAT CUSHION SHIELD LH
Engage the 2 claws.
Install the front lower seat cushion shield LH with the screw.
5.
INSTALL FRONT LOWER SEAT CUSHION SHIELD RH
Engage the 2 claws.
Install the front lower seat cushion shield RH with the screw.
6.
INSTALL UPPER RECLINING ADJUSTER INSIDE COVER LH
Engage the claw.
Install the upper reclining adjuster inside cover LH with the screw.
7.
INSTALL UPPER RECLINING ADJUSTER INSIDE COVER RH
Engage the claw.
Install the upper reclining adjuster inside cover RH with the screw.
8.
INSTALL LOWER RECLINING ADJUSTER INSIDE COVER LH
Install the lower reclining adjuster inside cover LH with the screw.
9.
INSTALL LOWER RECLINING ADJUSTER INSIDE COVER RH
Install the lower reclining adjuster inside cover RH with the screw.
10.
INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY
Install the lumbar support adjuster assembly with the 2 screws.
Connect the connector.
11.
INSTALL FRONT SEPARATE TYPE SEATBACK COVER (for Except Sports Seat Type)
Using hog ring pliers, install the front separate type seatback cover to the front seatback pad with 12 new hog rings.
NOTICE:
Be careful not to damage the cover.
When installing the hog rings, take care to minimize wrinkles as much as possible.
12.
INSTALL FRONT SEPARATE TYPE SEATBACK COVER (for Sports Seat Type)
Using hog ring pliers, install the front separate type seatback cover to the front seatback pad with 14 new hog rings.
NOTICE:
Be careful not to damage the cover.
When installing the hog rings, take care to minimize wrinkles as much as possible.
13.
INSTALL FRONT SEATBACK ASSEMBLY (for Except Sports Seat Type)
Install the front seatback assembly to the front seatback spring assembly.
Install the front seatback cover bracket with the nut.
Torque:
5.5 N*m{
56 kgf*cm
, 49 in.*lbf
}
NOTICE:
For vehicles with side airbags, the seatback cover must be securely installed. Otherwise, the side airbags may not deploy properly.
Make sure that the strap is not twisted after installing the bracket.
Install the bracket securely.
Engage the 6 hooks.
Using hog ring pliers, install 5 new hog rings.
Using hog ring pliers, install 3 new hog rings.
NOTICE:
Be careful not to damage the cover.
When installing the hog rings, take care to minimize wrinkles as much as possible.
14.
INSTALL FRONT SEATBACK ASSEMBLY (for Sports Seat Type)
Fully cover the airbag with the 2 seatback cover brackets and tighten the nut.
Torque:
5.5 N*m{
56 kgf*cm
, 49 in.*lbf
}
NOTICE:
For vehicles with side airbags, the seatback cover must be securely installed. Otherwise, the side airbags may not deploy properly.
Make sure that the strap is not twisted after installing the bracket.
Install the bracket securely.
Engage the 3 hooks.
Using hog ring pliers, install 2 new hog rings.
NOTICE:
Be careful not to damage the cover.
When installing the hog rings, take care to minimize wrinkles as much as possible.
15.
INSTALL FRONT SEAT HEADREST SUPPORT
Engage the 2 claws to install the front seat headrest support.
HINT:
Use the same procedure for the RH side and LH side.
16.
INSTALL FRONT SEATBACK BOARD SUB-ASSEMBLY (for Except Sports Seat Type)
Engage the 4 claws.
Install the front seatback board sub-assembly with the 2 screws.
17.
INSTALL FRONT SEATBACK BOARD SUB-ASSEMBLY (for Sports Seat Type)
Engage the 2 claws.
Engage the 14 claws.
Install the front seatback board sub-assembly with the 2 screws.
18.
INSTALL FRONT SEPARATE TYPE SEAT CUSHION COVER (for Except Sports Seat Type)
Using hog ring pliers, install the front separate type seat cushion cover to the front separate type seat pad with 16 new hog rings.
NOTICE:
Be careful not to damage the cover.
When installing the hog rings, take care to minimize wrinkles as much as possible.
19.
INSTALL FRONT SEPARATE TYPE SEAT CUSHION COVER (for Sports Seat Type)
Using hog ring pliers, install the front separate type seat cushion cover to the front separate type seat pad with 17 new hog rings.
NOTICE:
Be careful not to damage the cover.
When installing the hog rings, take care to minimize wrinkles as much as possible.
20.
INSTALL FRONT SEAT CUSHION ASSEMBLY
Engage the hooks.
Engage the 4 hooks.
Connect the connector.
21.
INSTALL FRONT SEAT INNER BELT ASSEMBLY
for LHD:
Install the front seat inner belt assembly with the nut.
Torque:
42 N*m{
428 kgf*cm
, 31 ft.*lbf
}
NOTICE:
Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding part of the front seat adjuster.
Connect the connector. (for Driver Seat)
Connect the connectors and engage each clamp.
Engage the 2 hooks.
for RHD Driver Seat:
Install the front seat inner belt assembly with the nut.
Torque:
42 N*m{
428 kgf*cm
, 31 ft.*lbf
}
NOTICE:
Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding part of the front seat adjuster.
Connect the connector.
Connect the connector and engage each clamp.
Engage the 2 hooks.
for RHD Passenger Seat:
Install the front seat inner belt assembly with the nut.
Torque:
42 N*m{
428 kgf*cm
, 31 ft.*lbf
}
NOTICE:
Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding part of the front seat adjuster.
Connect the connector and engage each clamp.
Engage the 2 hooks.
22.
INSTALL FRONT INNER SEAT CUSHION SHIELD
Engage the 3 claws.
Install the front inner seat cushion shield with the screw.
23.
INSTALL POWER SEAT SWITCH
Install the power seat switch with the 3 screws.
Connect the connector.
24.
INSTALL FRONT POWER SEAT LUMBAR SWITCH
Install the front power seat lumbar switch with the 2 screws.
25.
INSTALL FRONT INNER NO. 1 SEAT CUSHION SHIELD
Engage the 2 claws.
Install the front inner No. 1 seat cushion shield with the 2 screws.
26.
INSTALL FRONT SEAT CUSHION SHIELD ASSEMBLY
Connect the connector.
Engage the 2 claws.
Install the front seat cushion shield assembly with the 5 screws.
Install the 2 rubber bands on the backside of the front seatback board sub-assembly.
27.
INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB
Install the slide and vertical power seat switch knob.
28.
INSTALL RECLINING POWER SEAT SWITCH KNOB
Install the reclining power seat switch knob.