2006-2011 Camry Aurion · Service Manual STEERING

INSTALLATION

Removal / installation · Vehicles built Jun 2006 – Sep 2006

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009


1. INSTALL STEERING INTERMEDIATE SHAFT ASSEMBLY
  1. Align the matchmarks on the steering intermediate shaft assembly and the steering column assembly.

  1. C145838E01
    Install the bolt.

    Torque:
    35 N*m{ 360 kgf*cm , 26 ft.*lbf }


2. INSTALL STEERING COLUMN ASSEMBLY

  1. C145844E01
    Install the steering column assembly with the bolt and 2 nuts.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }

  1. Connect the connectors and engage the wire harness clamps to the steering column assembly.


3. CONNECT STEERING INTERMEDIATE SHAFT ASSEMBLY

  1. C132549E01
    Align the matchmarks on the steering intermediate shaft assembly and the power steering link assembly.

  1. C132548E02
    Install the bolt.

    Torque:
    35 N*m{ 360 kgf*cm , 26 ft.*lbf }

  1. C133172
    Install the clamp to the steering column hole shield.


4. INSTALL NO. 1 AIR DUCT

  1. C132547E02
    Engage the 2 claws to install the No. 1 air duct.


5. TURN FRONT WHEELS TO FACE STRAIGHT AHEAD

6. INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

  1. C145843
    Install the turn signal switch assembly with spiral cable sub-assembly to the steering column assembly with the clamp.

  1. Connect the connectors to the turn signal switch assembly with spiral cable sub-assembly.


7. INSTALL UPPER STEERING COLUMN COVER

  1. C145842
    Engage the claw to install the upper steering column cover.


8. INSTALL LOWER STEERING COLUMN COVER

  1. C145841
    Engage the 2 claws to install the lower steering column cover.

  1. Install the 2 screws.

    Torque:
    2.0 N*m{ 20 kgf*cm , 18 in.*lbf }


9. ADJUST SPIRAL CABLE SUB-ASSEMBLY
  1. Check that the ignition switch is off.

  1. Check that the battery negative (-) cable is disconnected.

    CAUTION:
    Wait for 90 seconds after disconnecting the cable to prevent airbag deployment.

  1. C107193
    Rotate the spiral cable counterclockwise slowly by hand until it feels firm.

    NOTICE:
    Do not turn the spiral cable by the airbag wire harness.

  1. C107194E01
    Rotate the spiral cable clockwise approximately 2.5 turns to align the marks.

    NOTICE:
    Do not turn the spiral cable by the airbag wire harness.

    HINT:
    The spiral cable will rotate approximately 2.5 turns to both the left and right from the center.


10. INSTALL STEERING WHEEL ASSEMBLY

  1. C145840E01
    Align the matchmarks on the steering wheel assembly and steering main shaft.

  1. Install the steering wheel assembly set nut.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }

  1. Connect the connectors to the spiral cable sub-assembly.


11. INSPECT STEERING WHEEL CENTER POINT

12. INSTALL STEERING PAD
  1. Check that the ignition switch is off.

  1. Check that the battery negative (-) cable is disconnected.

    CAUTION:
    Wait for 90 seconds after disconnecting the cable to prevent airbag deployment.

  1. C133859E01
    Support the steering pad with one hand.

  1. Connect the 2 airbag connectors to the steering pad.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. Connect the horn connector to the steering pad.

  1. Confirm that the circumference groove of the "TORX" screw fits in the screw case, and place the steering pad onto the steering wheel assembly.

  1. C146015E01
    Using a "TORX" socket (T30), tighten the 2 "TORX" screws.

    Torque:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }


13. INSTALL NO. 3 LOWER STEERING WHEEL COVER

  1. Engage the claw and install the No. 3 lower steering wheel cover.

    C146016E01


14. INSTALL NO. 2 LOWER STEERING WHEEL COVER

  1. Engage the claw and install the No. 2 lower steering wheel cover.

    C146017E01


15. INSPECT STEERING PAD

  1. C146010E01
    With the steering pad installed on the vehicle, perform a visual check. If there are any defects as mentioned below, replace the steering pad with a new one:
    1. Cuts, minute cracks or marked discoloration on the steering pad top surface or in the grooved portion.

  1. Make sure that the horn sounds.

    HINT:
    If the horn does not sound, inspect the horn system (Click here).


16. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL LH

  1. B147264E01
    Install the air hose and connect the connector.

  1. Engage the 2 claws and the DLC3.

  1. Engage the claw and the 4 clips.

  1. Install the lower No. 1 instrument panel finish panel with the screw <B> and bolt <A>.


17. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH

  1. B132116E01
    Engage the 2 clips.

  1. Install the cowl side trim sub-assembly LH with the cowl side trim clip.


18. INSTALL FRONT DOOR SCUFF PLATE LH

  1. B132067
    Engage the 7 claws and 3 clips, then install the front door scuff plate LH.


19. INSTALL FRONT WHEEL LH

Torque:
103 N*m{ 1,050 kgf*cm , 76 ft.*lbf }


20. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

21. INSPECT SRS WARNING LIGHT

HINT:
(Click here)

← REASSEMBLY (from Oct 2006)INSTALLATION (Oct 2006 – May 2009) →