Home › STEERING › STEERING COLUMN › STEERING COLUMN ASSEMBLY
INSTALLATION
Removal / installation · Vehicles built from Jun 2009
Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009
1.
INSTALL STEERING INTERMEDIATE SHAFT ASSEMBLY
Align the matchmarks on the steering intermediate shaft assembly and the steering column assembly.
Install the bolt.
Torque:
35 N*m{
360 kgf*cm
, 26 ft.*lbf
}
2.
INSTALL STEERING COLUMN ASSEMBLY
Install the steering column assembly with the bolt and 2 nuts.
Torque:
21 N*m{
214 kgf*cm
, 16 ft.*lbf
}
Connect the connectors and engage the wire harness clamps to the steering column assembly.
3.
CONNECT STEERING INTERMEDIATE SHAFT ASSEMBLY
Align the matchmarks on the steering intermediate shaft assembly and the power steering link assembly.
Install the bolt.
Torque:
35 N*m{
360 kgf*cm
, 26 ft.*lbf
}
Install the clamp to the steering column hole shield.
4.
INSTALL NO. 1 AIR DUCT
Engage the 2 claws to install the No. 1 air duct.
5.
TURN FRONT WHEELS TO FACE STRAIGHT AHEAD
6.
INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY
Install the turn signal switch assembly with spiral cable sub-assembly to the steering column assembly with the clamp.
Connect the connectors to the turn signal switch assembly with spiral cable sub-assembly.
7.
INSTALL UPPER STEERING COLUMN COVER
Engage the claw to install the upper steering column cover.
8.
INSTALL LOWER STEERING COLUMN COVER
Engage the 2 claws to install the lower steering column cover.
Install the 2 screws.
Torque:
2.0 N*m{
20 kgf*cm
, 18 in.*lbf
}
9.
ADJUST SPIRAL CABLE SUB-ASSEMBLY
Check that the ignition switch is off.
Check that the battery negative (-) cable is disconnected.
CAUTION:
Wait for 90 seconds after disconnecting the cable to prevent airbag deployment.
Rotate the spiral cable counterclockwise slowly by hand until it feels firm.
NOTICE:
Do not turn the spiral cable by the airbag wire harness.
Rotate the spiral cable clockwise approximately 2.5 turns to align the marks.
NOTICE:
Do not turn the spiral cable by the airbag wire harness.
HINT:
The spiral cable will rotate approximately 2.5 turns to both the left and right from the center.
10.
INSTALL STEERING WHEEL ASSEMBLY
Align the matchmarks on the steering wheel assembly and steering main shaft.
Install the steering wheel assembly set nut.
Torque:
50 N*m{
510 kgf*cm
, 37 ft.*lbf
}
Connect the connectors to the spiral cable sub-assembly.
11.
INSPECT STEERING WHEEL CENTER POINT
12.
INSTALL STEERING PAD
Check that the ignition switch is off.
Check that the battery negative (-) cable is disconnected.
CAUTION:
Wait for 90 seconds after disconnecting the cable to prevent airbag deployment.
Support the steering pad with one hand.
Connect the 2 airbag connectors to the steering pad.
NOTICE:
When handling the airbag connector, take care not to damage the airbag wire harness.
Connect the horn connector to the steering pad.
Confirm that the circumference groove of the "TORX" screw fits in the screw case, and place the steering pad onto the steering wheel assembly.
Using a "TORX" socket (T30), tighten the 2 "TORX" screws.
Torque:
8.8 N*m{
90 kgf*cm
, 78 in.*lbf
}
13.
INSTALL NO. 3 LOWER STEERING WHEEL COVER
Engage the claw and install the No. 3 lower steering wheel cover.
14.
INSTALL NO. 2 LOWER STEERING WHEEL COVER
Engage the claw and install the No. 2 lower steering wheel cover.
15.
INSTALL LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL (for 2GR-FE RHD)
Install the air hose and connect each connector.
Engage the claw and the 4 clips.
Engage the 2 claws and the DLC3.
Install the lower No. 1 instrument panel finish panel with the screw <F> and bolt <D>.
16.
INSTALL LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL (except 2GR-FE RHD)
Install the air hose and connect the connector.
Engage the 2 claws and the DLC3.
Engage the claw and the 4 clips.
Install the lower No. 1 instrument panel finish panel with the screw <B> and bolt <A>.
17.
INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH
Engage the 2 clips.
Install the cowl side trim sub-assembly LH with the cowl side trim clip.
18.
INSTALL FRONT DOOR SCUFF PLATE LH
Engage the 7 claws and 3 clips, then install the front door scuff plate LH.
19.
INSTALL FRONT WHEEL LH
Torque:
103 N*m{
1,050 kgf*cm
, 76 ft.*lbf
}
20.
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
21.
INSPECT STEERING PAD
With the steering pad installed on the vehicle, perform a visual check. If there are any defects as mentioned below, replace the steering pad with a new one: Cuts, minute cracks or marked discoloration on the steering pad top surface or in the grooved portion.
Make sure that the horn sounds.
HINT:
If the horn does not sound, inspect the horn system (Click here ).
22.
INSPECT SRS WARNING LIGHT
HINT:
(Click here )