2006-2011 Camry Aurion · Service Manual ENGINE

P0136 Oxygen Sensor Circuit Malfunction (Bank 1 Sensor 2)

Diagnostic trouble codes · Vehicles built Oct 2006 – May 2009

Also covers:

Versions by build date: Oct 2006 – May 2009 from Jun 2009

CAUTION / NOTICE / HINT


DESCRIPTION

A three-way catalytic converter (TWC) is used in order to convert the carbon monoxide (CO), hydrocarbon (HC), and nitrogen oxide (NOx) into less harmful substances. To allow the TWC to function effectively, it is necessary to keep the air-fuel ratio of the engine near the stoichiometric air-fuel ratio. For the purpose of helping the ECM to deliver accurate air-fuel ratio control, the Heated Oxygen (HO2) sensor is used.
The HO2 sensor is located behind the TWC, and detects the oxygen concentration in the exhaust gas. Since the sensor is integrated with the heater that heats the sensing portion, it is possible to detect the oxygen concentration even when the intake air volume is low (the exhaust gas temperature is low).
When the air-fuel ratio becomes lean, the oxygen concentration in the exhaust gas becomes rich. The HO2 sensor informs the ECM that the post-TWC air-fuel ratio is lean (low voltage, i.e. less than 0.45 V).
Conversely, when the air-fuel ratio is richer than the stoichiometric air-fuel level, the oxygen concentration in the exhaust gas becomes lean. The HO2 sensor informs the ECM that the post-TWC air-fuel ratio is rich (high voltage, i.e. more than 0.45 V). The HO2 sensor has the property of changing its output voltage drastically when the air-fuel ratio is close to the stoichiometric level.
The ECM uses the supplementary information from the HO2 sensor to determine whether the air-fuel ratio after the TWC is rich or lean, and adjusts the fuel injection time accordingly. Thus, if the HO2 sensor is working improperly due to internal malfunctions, the ECM is unable to compensate for deviations in the primary air-fuel ratio control.
A115539E09
DTC No.
DTC Detection Condition
Trouble Area
P0136
P0156
  1. Abnormal voltage output:
    1. During active air-fuel ratio control, following conditions (a) and (b) are met for a certain period of time (2 trip detection logic):
    2. (a) Heated Oxygen (HO2) sensor voltage does not decrease to less than 0.2 V
    3. (b) HO2 sensor voltage does not increase to more than 0.6 V
  2. Low impedance:
    1. Sensor impedance is less than 5 Ω for more than 30 seconds when ECM presumes sensor to be warmed up and operating normally (2 trip detection logic)
  1. Open or short in HO2 sensor (bank 1, 2 sensor 2) circuit
  2. HO2 sensor (bank 1, 2 sensor 2)
  3. HO2 sensor heater (bank 1, 2 sensor 2)
  4. Air-Fuel Ratio (A/F) sensor (bank 1, 2 sensor 1)
  5. EFI relay
  6. Gas leakage from exhaust system
P0137
P0157
  1. Low voltage (open):
    1. During active air-fuel ratio control, following conditions (a) and (b) are met for a certain period of time (2 trip detection logic):
    2. (a) HO2 sensor voltage output less than 0.21 V
    3. (b) Target air-fuel ratio rich
  2. High impedance:
    1. Sensor impedance is 15 kΩ or more for more than 90 seconds when ECM presumes sensor to be warmed up and operating normally (2 trip detection logic)
  1. Open in HO2 sensor (bank 1, 2 sensor 2) circuit
  2. HO2 sensor (bank 1, 2 sensor 2)
  3. HO2 sensor heater (bank 1, 2 sensor 2)
  4. EFI relay
  5. Gas leakage from exhaust system
P0138
P0158
  1. High voltage (short):
    1. During active air-fuel ratio control, following conditions (a) and (b) are met for a certain period of time (2 trip detection logic):
    2. (a) HO2 sensor voltage output 0.59 V or more
    3. (b) Target air-fuel ratio lean
  2. Extremely high voltage (short):
    1. HO2 sensor voltage output exceeds 1.2 V for more than 30 seconds (2 trip detection logic)
  1. Short in HO2 sensor (bank 1, 2 sensor 2) circuit
  2. HO2 sensor (bank 1, 2 sensor 2)
  3. ECM internal circuit malfunction

WIRING DIAGRAM

A154324E01

CONFIRMATION DRIVING PATTERN

HINT:
  1. This confirmation driving pattern is used in steps 5, 8 and 11 of the following diagnostic troubleshooting procedure when using an intelligent tester.
  2. Performing this confirmation driving pattern will activate the Heated Oxygen (HO2) sensor monitor. (The catalyst monitor is performed simultaneously.) This is very useful for verifying the completion of a repair.

NOTICE:
This test will not be completed if the vehicle is driven at an absolutely constant speed conditions such as with cruise control activated.

A237149E01
  1. Connect an intelligent tester to the DLC3.
  2. Turn the ignition switch on (IG).
  3. Turn the tester on.
  4. Clear the DTCs (where set) (Click here).
  5. Start the engine and warm it up (Procedure "A").
  6. Drive the vehicle at between 64 km/h and 113 km/h (40 mph and 70 mph) for at least 10 minutes (Procedure "B").
  7. On the tester, select the following menu items: Powertrain / Engine / DTC / Pending and check if any DTCs (any pending DTCs) are set.

INSPECTION PROCEDURE

HINT:
Intelligent tester only:
Malfunctioning areas can be identified by performing the Control the Injection Volume for A/F Sensor function provided in the Active Test. The Control the Injection Volume for A/F Sensor function can help to determine whether the Air-Fuel Ratio (A/F) sensor, Heated Oxygen (HO2) sensor and other potential trouble areas are malfunctioning.
The following instructions describe how to conduct the Control the Injection Volume for A/F Sensor operation using an intelligent tester.
  1. Connect the intelligent tester to the DLC3.
  2. Start the engine and turn the tester on.
  3. Warm up the engine at an engine speed of 2,500 rpm for approximately 90 seconds.
  4. On the tester, enter the following menus: Powertrain / Active Test / Control the Injection Volume for A/F Sensor.
  5. Perform the Control the Injection Volume for A/F Sensor operation with the engine in an idling condition (press the RIGHT or LEFT button to change the fuel injection volume).
  6. Monitor the voltage outputs of the A/F and HO2 sensors (AFS B1S1 and O2S B1S2 or AFS B2S1 and O2S B2S2) displayed on the tester.

HINT:
  1. The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 25%.
  2. Each sensor reacts in accordance with increases in the fuel injection volume.

Tester Display
(Sensor)
Injection Volume
Status
Voltage
AFS B1S1 or AFS B2S1
(A/F)
+25%
Rich
Less than 3.0 V
AFS B1S1 or AFS B2S1
(A/F)
-12.5%
Lean
More than 3.35 V
O2S B1S2 or O2S B2S2
(HO2)
+25%
Rich
More than 0.55 V
O2S B1S2 or O2S B2S2
(HO2)
-12.5%
Lean
Less than 0.4 V

NOTICE:
The Air-Fuel Ratio (A/F) sensor has an output delay of a few seconds and the Heated Oxygen (HO2) sensor has a maximum delay of approximately 20 seconds.

Case
A/F Sensor (Sensor 1)
Output Voltage
HO2 Sensor (Sensor 2)
Output Voltage
Main Suspected Trouble Area
1
Injection Volume
+25%
-12.5%
A103184
Injection Volume
+25%
-12.5%
A103184
-
Output Voltage
More than 3.35 V
Less than 3.0 V
A107708
Output Voltage
More than 0.55 V
Less than 0.4 V
A103186
2
Injection Volume
+25%
-12.5%
A103184
Injection Volume
+25%
-12.5%
A103184
  1. A/F sensor
  2. A/F sensor heater
  3. A/F sensor circuit
Output Voltage
Almost no reaction
A103185
Output Voltage
More than 0.55 V
Less than 0.4 V
A103186
3
Injection Volume
+25%
-12.5%
A103184
Injection Volume
+25%
-12.5%
A103184
  1. HO2 sensor
  2. HO2 sensor heater
  3. HO2 sensor circuit
Output Voltage
More than 3.35 V
Less than 3.0 V
A107708
Output Voltage
Almost no reaction
A103185
4
Injection Volume
+25%
-12.5%
A103184
Injection Volume
+25%
-12.5%
A103184
  1. Fuel pressure
  2. Gas leakage from exhaust system
    (Air-fuel ratio extremely lean or rich)
Output Voltage
Almost no reaction
A103185
Output Voltage
Almost no reaction
A103185
  1. - Following the Control the Injection Volume for A/F Sensor procedure enables technicians to check and graph the voltage outputs of both the A/F and HO2 sensors.
  2. - The following A/F Control procedure enables the technician to check and graph the voltage output of both the heated oxygen sensors. To display the graph, select the following menu items on the tester: View / Line graph.

HINT:
  1. Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction (Click here).
  2. If the OX1B wire from the ECM connector is short-circuited to the +B wire, DTC P0136 will be set.
  3. If the OX2B wire from the ECM connector is short-circuited to the +B wire, DTC P0156 will be set.


1. READ DTC OUTPUT
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester on.

  1. Enter the following menus: Powertrain / Engine / DTC.

  1. Read the DTCs.

    Result:
    Display (DTC Output)
    Proceed to
    P0138 or P0158
    A
    P0137 or P0157
    B
    P0136 or P0156
    C



B
Go to step 14

C
Go to step 7
A


2. READ VALUE USING OXYGEN SENSOR (OUTPUT VOLTAGE)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester on.

  1. Enter the following menus: Powertrain / Engine / Data List / O2S B1S2 or O2S B2S2.

  1. Allow the engine to idle.

  1. Read the Heated Oxygen (HO2) sensor output voltage while idling.

    Result:
    HO2 Sensor Output Voltage
    Proceed to
    More than 1.2 V
    A
    Less than 1.0 V
    B



B
Go to step 5
A


3. CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT)

  1. A139137E01
    Turn the ignition switch off and wait for 5 minutes.

  1. Disconnect the C58 (RHD) or C55 (LHD) ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    RHD:
    Tester Connection
    Specified Condition
    HT1B (C58-48) - OX1B (C58-88)
    10 kΩ or higher
    HT2B (C58-47) - OX2B (C58-87)
    10 kΩ or higher
    LHD:
    Tester Connection
    Specified Condition
    HT1B (C55-48) - OX1B (C55-88)
    10 kΩ or higher
    HT2B (C55-47) - OX2B (C55-87)
    10 kΩ or higher

  1. Reconnect the ECM connector.



NG
Go to step 4
OK

REPLACE ECM (Click here)

4. INSPECT HEATED OXYGEN SENSOR (CHECK FOR SHORT)

  1. A137614E16
    Disconnect the C52 oxygen sensor connector (Bank 1 Sensor 2) or C51 oxygen sensor connector (Bank 2 sensor 2).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Bank 1 sensor 2:
    Tester Connection
    Specified Condition
    +B (2) - E2 (4)
    10 kΩ or higher
    +B (2) - OX1B (3)
    10 kΩ or higher
    Bank 2 sensor 2:
    Tester Connection
    Specified Condition
    +B (2) - E2 (4)
    10 kΩ or higher
    +B (2) - OX2B (3)
    10 kΩ or higher



NG
REPLACE HEATED OXYGEN SENSOR (Click here)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

5. PERFORM CONFIRMATION DRIVING PATTERN

NEXT


6. CHECK WHETHER DTC OUTPUT RECURS (DTC P0138 or P0158)
  1. On the intelligent tester, enter the following menus: Powertrain / Engine / DTC.

  1. Read the DTCs.

    Result:
    Display (DTC Output)
    Proceed to
    P0138 or P0158
    A
    No output
    B



B
CHECK FOR INTERMITTENT PROBLEMS
A

REPLACE HEATED OXYGEN SENSOR (Click here)

7. READ VALUE USING OXYGEN SENSOR (OUTPUT VOLTAGE)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester on.

  1. Start the engine.

  1. Enter the following menus: Powertrain / Engine / DTC / Data List / O2S B1S2 or O2S B1S2.

  1. After warming up the engine, run the engine at an engine speed of 2,500 rpm for 3 minutes.

  1. Read the output voltage of the HO2 sensor when the engine rpm is suddenly increased.

    HINT:
    Quickly accelerate the engine to 4,000 rpm 3 times using the accelerator pedal.

    Standard voltage:
    Fluctuates between 0.4 V or less and 0.55 V or more.



NG
Go to step 14
OK


8. PERFORM CONFIRMATION DRIVING PATTERN

NEXT


9. CHECK WHETHER DTC OUTPUT RECURS (DTC P0136 or P0156)
  1. On the intelligent tester, enter the following menus: Powertrain / Engine / DTC.

  1. Read the DTCs.

    Result:
    Display (DTC Output)
    Proceed to
    P0136 or P0156
    A
    No output
    B



B
CHECK FOR INTERMITTENT PROBLEMS
A


10. REPLACE HEATED OXYGEN SENSOR
  1. Replace the heated oxygen sensor (Click here).


NEXT


11. PERFORM CONFIRMATION DRIVING PATTERN

NEXT


12. CHECK WHETHER DTC OUTPUT RECURS (DTC P0136 or P0156)
  1. On the intelligent tester, enter the following menus: Powertrain / Engine / DTC.

  1. Read the DTCs.

    Result:
    Display (DTC Output)
    Proceed to
    P0136 or P0156
    A
    No output
    B



B
END
A


13. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (INJECTION VOLUME)
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine and turn the tester on.

  1. Warm up the engine.

  1. Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume.

  1. Change the fuel injection volume using the tester, while monitoring the output voltage of Air-Fuel Ratio (A/F) and HO2 sensor displayed on the tester.

HINT:
  1. Change the fuel injection volume within the range of -12% and +12%. The injection volume can be changed in 1% graduations within the range.
  2. The A/F sensor is displayed as AFS B1S1 or AFS B2S1, and the HO2 sensor is displayed as O2S B1S2 or O2S B2S2, on the intelligent tester.


Result:
Tester Display (Sensor)
Voltage Variation
Proceed to
AFS B1S1 (A/F)
AFS B2S1 (A/F)
Alternates between more and less than 3.3 V
OK
AFS B1S1 (A/F)
AFS B2S1 (A/F)
Remains more than 3.3 V
NG
AFS B1S1 (A/F)
AFS B2S1 (A/F)
Remains less than 3.3 V
NG

HINT:
A normal HO2 sensor voltage (O2S B1S2 or O2S B2S2) reacts in accordance with increases and decreases in fuel injection volumes. When the A/F sensor voltage remains either less or more than 3.3 V despite the HO2 sensor indicating a normal reaction, the A/F sensor is malfunctioning.

A087979E17


NG
REPLACE AIR FUEL RATIO SENSOR
OK

CHECK AND REPAIR EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO (INJECTOR, FUEL PRESSURE, GAS LEAKAGE FROM EXHAUST SYSTEM)

14. INSPECT FOR EXHAUST GAS LEAK

OK:
No gas leakage.



NG
REPAIR OR REPLACE EXHAUST GAS LEAKAGE POINT
OK


15. INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)

  1. A137614E15
    Disconnect the C52 oxygen sensor connector (Bank 1 Sensor 2) or C51 oxygen sensor connector (Bank 2 sensor 2).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Bank 1 sensor 2:
    Tester Connection
    Condition
    Specified Condition
    HT1B (1) - +B (2)
    20°C (68°F)
    11 to 16 Ω
    HT1B (1) - E2 (4)
    Always
    10 kΩ or higher
    Bank 2 sensor 2:
    Tester Connection
    Condition
    Specified Condition
    HT2B (1) - +B (2)
    20°C (68°F)
    11 to 16 Ω
    HT2B (1) - E2 (4)
    Always
    10 kΩ or higher



NG
REPLACE HEATED OXYGEN SENSOR (Click here)
OK


16. INSPECT ENGINE ROOM JUNCTION BLOCK (EFI RELAY)

  1. A150648E03
    Remove the engine room junction block from the engine room R/B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Terminal Connection
    Specified Condition
    1E-12 - 1E-6
    10 kΩ or higher
    1E-12 - 1E-6
    Below 1 Ω
    (when battery voltage applied to terminals 1E-9 and 1E-10)

  1. Reinstall the engine room junction block.



NG
REPLACE ENGINE ROOM JUNCTION BLOCK
OK


17. CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)

  1. A137615E09
    Disconnect the C52 oxygen sensor connector (Bank 1 Sensor 2) or C51 oxygen sensor connector (Bank 2 sensor 2).

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Terminal Connection
    Specified Condition
    +B (C52-2) - Body ground
    9 to 14 V
    +B (C51-2) - Body ground
    9 to 14 V

  1. Turn the ignition switch off.

  1. Disconnect the C58 (RHD) or C55 (LHD) ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    RHD:
    Terminal Connection
    Specified Condition
    HT1B (C52-1) - HT1B (C58-48)
    Below 1 Ω
    OX1B (C52-3) - OX1B (C58-88)
    Below 1 Ω
    E2 (C52-4) - EX1B (C58-65)
    Below 1 Ω
    HT2B (C51-1) - HT2B (C58-47)
    Below 1 Ω
    OX2B (C51-3) - OX2B (C58-87)
    Below 1 Ω
    E2 (C51-4) - EX2B (C58-64)
    Below 1 Ω
    LHD:
    Terminal Connection
    Specified Condition
    HT1B (C52-1) - HT1B (C55-48)
    Below 1 Ω
    OX1B (C52-3) - OX1B (C55-88)
    Below 1 Ω
    E2 (C52-4) - EX1B (C55-65)
    Below 1 Ω
    HT2B (C51-1) - HT2B (C55-47)
    Below 1 Ω
    OX2B (C51-3) - OX2B (C55-87)
    Below 1 Ω
    E2 (C51-4) - EX2B (C55-64)
    Below 1 Ω


    Standard resistance (Check for short):
    RHD:
    Terminal Connection
    Specified Condition
    HT1B (C52-1) or HT1B (C58-48) - Body ground
    10 kΩ or higher
    OX1B (C52-3) or OX1B (C58-88) - Body ground
    10 kΩ or higher
    E2 (C52-4) or EX1B (C58-65) - Body ground
    10 kΩ or higher
    HT2B (C51-1) or HT2B (C58-47) - Body ground
    10 kΩ or higher
    OX2B (C51-3) or OX2B (C58-87) - Body ground
    10 kΩ or higher
    E2 (C51-4) or EX2B (C58-64) - Body ground
    10 kΩ or higher
    LHD:
    Terminal Connection
    Specified Condition
    HT1B (C52-1) or HT1B (C55-48) - Body ground
    10 kΩ or higher
    OX1B (C52-3) or OX1B (C55-88) - Body ground
    10 kΩ or higher
    E2 (C52-4) or EX1B (C55-65) - Body ground
    10 kΩ or higher
    HT2B (C51-1) or HT2B (C55-47) - Body ground
    10 kΩ or higher
    OX2B (C51-3) or OX2B (C55-87) - Body ground
    10 kΩ or higher
    E2 (C51-4) or EX2B (C55-64) - Body ground
    10 kΩ or higher

  1. Reconnect the HO2 sensor connector.

  1. Reconnect the ECM connector.A103832E54



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE HEATED OXYGEN SENSOR (Click here)


← P0121 Throttle / Pedal Position Sensor / Switch "A" Circuit Range / Performance Problem (from Jun 2009)P0136 Oxygen Sensor Circuit Malfunction (Bank 1 Sensor 2) (+ 5 more codes) (from Jun 2009) →