2006-2011 Camry Aurion · Service Manual ENGINE

P0031 Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 1 Sensor 1)

Diagnostic trouble codes · Vehicles built from Jun 2009

Also covers:

Versions by build date: Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

HINT:
  1. Although the DTC titles include oxygen sensor, these DTCs relate to the Air-Fuel Ratio (A/F) sensor.
  2. Sensor 1 refers to the sensor mounted in front of the Three-Way Catalytic Converter (TWC) and located near the engine assembly.

The A/F sensor generates voltage* that corresponds to the actual air-fuel ratio. This sensor voltage is used to provide the ECM with feedback so that it can control the air-fuel ratio. The ECM determines the deviation from the stoichiometric air-fuel ratio level, and regulates the fuel injection time. If the A/F sensor malfunctions, the ECM is unable to control the air-fuel ratio accurately.
The A/F sensor is the planar type and is integrated with the heater, which heats the solid electrolyte (zirconia element). This heater is controlled by the ECM. When the intake air volume is low (the exhaust gas temperature is low), a current flows into the heater to heat the sensor, in order to facilitate accurate oxygen concentration detection. In addition, the sensor and heater portions are narrower than the conventional type. The heat generated by the heater is conducted to the solid electrolyte through the alumina, therefore the sensor activation is accelerated.
A three-way catalytic converter (TWC) is used in order to convert the carbon monoxide (CO), hydrocarbon (HC), and nitrogen oxide (NOx) into less harmful substances. To allow the TWC to function effectively, it is necessary to keep the air-fuel ratio of the engine near the stoichiometric air-fuel ratio.
*: Value changes inside the ECM. Since the A/F sensor is the current output element, a current is converted to a voltage inside the ECM. Any measurements taken at the A/F sensor or ECM connectors will show a constant voltage.
A173183E21

HINT:
  1. When any of these DTCs are set, the ECM enters fail-safe mode. The ECM turns off the A/F sensor heater in fail-safe mode. Fail-safe mode continues until the ignition switch is turned off.

  2. The ECM provides a pulse width modulated control circuit to adjust the current through the heater. The A/F sensor heater circuit uses a relay on the B+ side of the circuit.

    A133850E13

DTC No.
DTC Detection Condition
Trouble Area
P0031
P0051
Air-Fuel Ratio (A/F) sensor heater (bank 1, 2, sensor 1) current is less than 0.8 A (1 trip detection logic)
  1. Open in A/F sensor heater (bank 1, 2, sensor 1) circuit
  2. A/F sensor heater (bank 1, 2, sensor 1)
  3. A/F relay
  4. ECM
P0032
P0052
Air-Fuel Ratio (A/F) sensor heater (bank 1, 2, sensor 1) current is more than 10 A (1 trip detection logic)
  1. Short in A/F sensor heater (bank 1, 2, sensor 1) circuit
  2. A/F sensor heater (sensor 1)
  3. A/F relay
  4. ECM

HINT:
  1. Bank 1 refers to the bank that includes cylinder No. 1.
  2. Bank 2 refers to the bank that does not include cylinder No. 1.
  3. Sensor 1 refers to the sensor closest to the engine assembly.
  4. Sensor 2 refers to the sensor farthest away from the engine assembly.


WIRING DIAGRAM

Refer to DTC P2195 (Click here)

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction (Click here).


1. INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)

  1. A140627E04
    Disconnect the C15 or C35 A/F sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Bank 1 sensor 1:
    Tester Connection
    Condition
    Specified Condition
    HA1A (1) - +B (2)
    20°C (68°F)
    1.8 to 3.4 Ω
    HA1A (1) - A1A- (4)
    -
    10 kΩ or higher
    Bank 2 sensor 1:
    Tester Connection
    Condition
    Specified Condition
    HA2A (1) - +B (2)
    20°C (68°F)
    1.8 to 3.4 Ω
    HA2A (1) - A2A- (4)
    -
    10 kΩ or higher

  1. Reconnect the A/F sensor connector.



NG
REPLACE AIR FUEL RATIO SENSOR (Click here)
OK


2. CHECK TERMINAL VOLTAGE (+B OF A/F SENSOR)

  1. A076787E15
    Disconnect the C15 or C35 A/F sensor connector.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage between the terminals of the A/F sensor connector and body ground.

    Standard voltage:
    Tester Connection
    Specified Condition
    +B (C15-2) - Body ground
    9 to 14 V
    +B (C35-2) - Body ground
    9 to 14 V



OK
Go to step 7
NG


3. INSPECT FUSE (A/F)
  1. Remove the A/F fuse from the engine room junction block.

  1. Measure the A/F fuse resistance.

    Standard resistance:
    Below 1 Ω

  1. Reinstall the A/F fuse.



NG
REPLACE A/F FUSE
OK


4. INSPECT ENGINE ROOM JUNCTION BLOCK (EFI RELAY, A/F RELAY)

  1. A150648E05
    Remove the engine room junction block from the engine room R/B.

  1. Inspect the EFI relay.

    1. Measure the EFI relay resistance.

      Standard resistance:
      Tester Connection
      Specified Condition
      1E-12 - 1E-6
      10 kΩ or higher
      1E-12 - 1E-6
      Below 1 Ω
      (Apply battery voltage between terminals 1E-9 and 1E-10)

  1. Inspect the A/F relay.

    1. Measure the A/F relay resistance.

      Standard resistance:
      Tester Connection
      Specified Condition
      1G-1 - 1A-4
      10 kΩ or higher
      1G-1 - 1A-4
      Below 1 Ω
      (Apply battery voltage between terminals 1E-11 and 1E-6)



NG
REPLACE ENGINE ROOM JUNCTION BLOCK
OK


5. INSPECT FUSE (EFI MAIN)

  1. A135017E01
    Remove the EFI MAIN fuse from the engine room R/B.

  1. Measure the EFI MAIN fuse resistance.

    Standard resistance:
    Below 1 Ω

  1. Reinstall the EFI MAIN fuse.



NG
REPLACE EFI MAIN FUSE
OK


6. CHECK HARNESS AND CONNECTOR (A/F SENSOR - A/F RELAY)

  1. A141109E07
    Disconnect the C15 or C35 A/F sensor connector.

  1. Remove the engine room junction block from the engine room R/B.

  1. Measure the resistance between the terminals.

    Standard resistance:
    Check for open:
    Tester Connection
    Specified Condition
    +B (C15-2) - 1A-4 (Engine room R/B)
    Below 1 Ω
    +B (C35-2) - 1A-4 (Engine room R/B)
    Below 1 Ω
    Check for short:
    Tester Connection
    Specified Condition
    +B (C15-2) or 1A-4 (Engine room R/B) - Body ground
    10 kΩ or higher
    +B (C35-2) or 1A-4 (Engine room R/B) - Body ground
    10 kΩ or higher

  1. Reinstall the engine room junction block.

  1. Reconnect the A/F sensor connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK ECM POWER SOURCE CIRCUIT

7. CHECK HARNESS AND CONNECTOR

  1. A127715E52
    Disconnect the C15 or C35 A/F sensor connector.

  1. Disconnect the C58 (RHD) or C55 (LHD) ECM connector.

  1. Measure the resistance between the terminals.

    Standard resistance (Check for open):
    RHD:
    Tester Connection
    Specified Condition
    HA1A (C58-86) - HA1A (C15-1)
    Below 1 Ω
    HA2A (C58-109) - HA2A (C35-1)
    Below 1 Ω
    LHD:
    Tester Connection
    Specified Condition
    HA1A (C55-86) - HA1A (C15-1)
    Below 1 Ω
    HA2A (C55-109) - HA2A (C35-1)
    Below 1 Ω


    Standard resistance (Check for short):
    RHD:
    Tester Connection
    Specified Condition
    HA1A (C58-86) or HA1A (C15-1) - Body ground
    10 kΩ or higher
    HA2A (C58-109) or HA2A (C35-1) - Body ground
    10 kΩ or higher
    LHD:
    Tester Connection
    Specified Condition
    HA1A (C55-86) or HA1A (C15-1) - Body ground
    10 kΩ or higher
    HA2A (C55-109) or HA2A (C35-1) - Body ground
    10 kΩ or higher

  1. Reconnect the ECM connector.

  1. Reconnect the A/F sensor connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8. CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the intelligent tester on.

  1. Clear the DTCs (Click here).

  1. Start the engine.

  1. Allow the engine to idle for 1 minute or more.

  1. Select the following menu items: Powertrain / Engine / DTC.

  1. Read the DTCs.

    Result:
    Display (DTC Output)
    Proceed to
    No output
    A
    P0031, P0032, P0051 and/or P0052
    B



B
REPLACE ECM (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS


← P0031 Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 1 Sensor 1) (+ P0032, P0051, P0052) (Oct 2006 – May 2009)P0037 Oxygen Sensor Heater Control Circuit Low (Bank 1 Sensor 2) (+ P0038, P0057, P0058) (Oct 2006 – May 2009) →