Open in CAN Main Bus Line
Circuit diagnosis · Vehicles built Jun 2006 – Sep 2006
DESCRIPTION
There may be an open circuit in the CAN main bus wire and/or the DLC3 branch wire when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is 69 Ω or more.| Symptom |
Trouble Area |
| Resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is 69 Ω or more. |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- Turn the ignition switch off before measuring the resistances of CAN main wires and CAN branch wires.
- After the ignition switch is turned off, check that the key reminder warning system and lighting system are not operating.
- Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If doors need to be opened in order to check connectors, open the doors and leave them open.
- Turn the ignition switch off before measuring the resistances of CAN main wires and CAN branch wires.
- HINT:
- Operating the ignition switch, any other switches, or any doors triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
| 1. CHECK DLC3 |
Turn the ignition switch off.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
Result
E10-6 (CANH) -E10-14 (CANL)
Ignition switch off
108 to 132 Ω
A
E10-6 (CANH) - E10-14 (CANL)
Ignition switch off
132 Ω or higher
B
- NOTICE:
- When the measured value is 132 Ω or more and a CAN communication system diagnostic trouble code is output, there may be a fault besides disconnection of the DLC3 branch wire. For that reason, troubleshooting should be performed again from "HOW TO PROCEED WITH TROUBLESHOOTING" (Click here) after repairing the trouble area.
|
|
||||
| A | |
| 2. CHECK FOR OPEN IN CAN BUS MAIN WIRE (COMBINATION METER MAIN BUS WIRE) |
Disconnect the CAN main bus wire connector (E43) from the No. 1 CAN J/C "B" side (without earth terminal).

- NOTICE:
- Before disconnecting the connector, make a note of where it is connected.
- Reconnect the connector to its original position.
- Before disconnecting the connector, make a note of where it is connected.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
E43-1 (CANH) - E43-2 (CANL)
Ignition switch off
108 to 132 Ω
|
|
||||
| OK | |
| 3. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 1 CAN J/C) |
Reconnect the CAN main bus wire connector (E43) to the No. 1 CAN J/C "B" side (without earth terminal).

Disconnect the CAN main bus wire connector (E42) from the No. 1 CAN J/C "A" side (with earth terminal).
- NOTICE:
- Before disconnecting the connector, make a note of where it is connected.
- Reconnect the connector to its original position.
- Before disconnecting the connector, make a note of where it is connected.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
E42-1 (CANH) - E42-2 (CANL)
Ignition switch off
108 to 132 Ω
|
|
||||
| NG | |
| 4. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 1 CAN J/C - NO. 4 CAN J/C) |
Reconnect the CAN main bus wire connector (E42) to the No. 1 CAN J/C "A" side (with earth terminal).
Disconnect the CAN main bus wire connector (E41) from the No. 4 CAN J/C (rear of the vehicle).

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
E41-4 (CANH) - E41-10 (CANL)
Ignition switch off
108 to 132 Ω
|
|
||||
| OK | |
| 5. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 4 CAN J/C) |
Reconnect the CAN main bus wire connector (E41) to the No. 4 CAN J/C (rear of the vehicle).

Disconnect the CAN main bus wire connector (A40) from the No. 4 CAN J/C (front of the vehicle).
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
A40-1 (CANH) - A40-7 (CANL)
Ignition switch off
108 to 132 Ω
|
|
||||
| NG | |
| 6. CHECK FOR OPEN IN CAN BUS MAIN WIRE (ECM CAN MAIN BUS WIRE) |
Reconnect the CAN main bus wire connector (A40) to the No. 4 CAN J/C (front of the vehicle).

Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
A24-41 (CANH) - A24-49 (CANL)
Ignition switch off
108 to 132 Ω
|
|
||||
| NG | ||
| ||
| 7. CHECK FOR OPEN IN CAN BUS MAIN WIRE (COMBINATION METER - NO. 1 CAN J/C) |
Reconnect the CAN main bus wire connector (E43) to the No. 1 CAN J/C "B" side (without earth terminal).
Disconnect the combination meter connector (F1).

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
F1-23 (CANH) - F1-22 (CANL)
Ignition switch off
108 to 132 Ω
|
|
||||
| NG | ||
| ||
