2006-2011 Camry Aurion · Service Manual COMMUNICATION SYSTEM

Open in CAN Main Bus Line

Circuit diagnosis · Vehicles built Oct 2006 – May 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

There may be an open circuit in the CAN No. 1 bus main wire and/or the DLC3 branch wire when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is 69 Ω or more.
Symptom
Trouble Area
Resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is 69 Ω or more.
  1. CAN bus main wire or connector
  2. CAN No. 4 J/C
  3. CAN No. 6 J/C
  4. DLC3 branch wire or connector
  5. Combination meter
  6. ECM

WIRING DIAGRAM

C123381E07

INSPECTION PROCEDURE

NOTICE:
  1. Turn the engine switch off before measuring the resistances of CAN bus main wires and CAN bus branch wires.
  2. After the engine switch is turned off, check that the key reminder warning system and lighting system are not operating.
  3. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the engine switch, any other switches, or the doors. If any doors need to be opened in order to check connectors, open the doors and leave them open.

HINT:
Operating the engine switch, any other switches, or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.


1. CHECK DLC3

  1. C126400E08
    Turn the engine switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    Result
    E10-6 (CANH) -E10-14 (CANL)
    Engine switch off
    108 to 132 Ω
    A
    E10-6 (CANH) - E10-14 (CANL)
    Engine switch off
    132 Ω or higher
    B

    NOTICE:
    When the measured value is 132 Ω or more and a CAN communication system diagnostic trouble code is output, there may be a fault besides disconnection of the DLC3 branch wire. For that reason, troubleshooting should be performed again from "HOW TO PROCEED WITH TROUBLESHOOTING" (Click here) after repairing the trouble area.



B
REPAIR OR REPLACE DLC3 BRANCH WIRE OR CONNECTOR (CANH, CANL)
A


2. CHECK FOR OPEN IN CAN NO. 1 BUS WIRE (COMBINATION METER MAIN BUS WIRE)

  1. C133231E05
    Disconnect CAN main bus wire connector E43 from the CAN No. 1 J/C "B" side (without earth terminal).

    NOTICE:
    1. Before disconnecting the connector, make a note of where it is connected.
    2. Reconnect the connector to its original position.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    E43-1 (CANH) - E43-2 (CANL)
    Engine switch off
    108 to 132 Ω



NG
Go to step 7
OK


3. CHECK FOR OPEN IN CAN NO. 1 BUS MAIN WIRE (CAN NO. 1 J/C)

  1. C142742E04
    Reconnect CAN main bus wire connector E43 to the CAN No. 1 J/C "B" side (without earth terminal).

  1. Disconnect CAN main bus wire connector E42 from the CAN No. 1 J/C "A" side (with earth terminal).

    NOTICE:
    1. Before disconnecting the connector, make a note of where it is connected.
    2. Reconnect the connector to its original position.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    E42-1 (CANH) - E42-2 (CANL)
    Engine switch off
    108 to 132 Ω



OK
REPLACE CAN NO. 1 J/C
NG


4. CHECK FOR OPEN IN CAN NO. 1 BUS MAIN WIRE (CAN NO. 1 J/C - CAN NO. 4 J/C)
  1. Reconnect CAN main bus wire connector E42 to the CAN No. 1 J/C "A" side (with earth terminal).

  1. C133246E13
    Disconnect CAN main bus wire connector E41 from the CAN No. 4 J/C (front of the vehicle).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    E41-4 (CANH) - E41-10 (CANL)
    Engine switch off
    108 to 132 Ω



NG
REPAIR OR REPLACE CAN NO. 1 BUS MAIN WIRE OR CONNECTOR (CAN NO. 1 J/C - CAN NO. 4 J/C)
OK


5. CHECK FOR OPEN IN CAN NO. 1 BUS MAIN WIRE (CAN NO. 4 J/C)

  1. C133245E10
    Reconnect CAN main bus wire connector E41 to the CAN No. 4 J/C (front of the vehicle).

  1. Disconnect CAN main bus wire connector A40 from the CAN No. 4 J/C (rear of the vehicle).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    A40-1 (CANH) - A40-7 (CANL)
    Engine switch off
    108 to 132 Ω



OK
REPLACE CAN NO. 4 J/C
NG


6. CHECK FOR OPEN IN CAN NO. 1 BUS MAIN WIRE (ECM CAN MAIN BUS WIRE)
  1. Reconnect CAN main bus wire connector A40 to the CAN No. 4 J/C (rear of the vehicle).

  1. G100098E19
    Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    A55-41 (CANH) - A55-49 (CANL)
    Engine switch off
    108 to 132 Ω



OK
REPLACE ECM
NG

REPAIR OR REPLACE CAN NO. 1 BUS MAIN WIRE OR CONNECTOR (CAN NO. 4 J/C - ECM)

7. CHECK FOR OPEN IN CAN NO. 1 BUS MAIN WIRE (COMBINATION METER - CAN NO. 1 J/C)
  1. Reconnect CAN main bus wire connector E43 to the CAN No. 1 J/C "B" side (without earth terminal).

  1. C133243E01
    Disconnect combination meter connector F1.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    F1-17 (CANH) - F1-18 (CANL)
    Engine switch off
    108 to 132 Ω



OK
REPLACE COMBINATION METER
NG

REPAIR OR REPLACE CAN NO. 1 BUS MAIN WIRE OR CONNECTOR (CAN NO. 1 J/C - COMBINATION METER)


← CAN Bus Line (from Jun 2009)Open in CAN Main Bus Line (from Jun 2009) →