Short in CAN Bus Lines
Circuit diagnosis · Vehicles built Oct 2006 – May 2009
Versions by build date: Oct 2006 – May 2009 from Jun 2009
DESCRIPTION
The CAN bus wires are considered to be shorted when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 54 Ω.| Symptom |
Trouble Area |
| Resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 54 Ω. |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- Turn the ignition switch off before measuring the resistances of CAN main wires and CAN branch wires.
- After the ignition switch is turned off, check that the key reminder warning system and lighting system are not operating.
- Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If doors need to be opened in order to check connectors, open the doors and leave them open.
- Turn the ignition switch off before measuring the resistances of CAN main wires and CAN branch wires.
- HINT:
- Operating the ignition switch, any other switches, or any doors triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
| 1. CHECK FOR SHORT IN CAN BUS WIRES (DLC3 BRANCH WIRE) |
Turn the ignition switch off.

Disconnect the DLC3 branch wire connector (E62) from the No. 1 CAN J/C "B" side (without earth terminal).
- NOTICE:
- Before disconnecting the connector, make a note of where it is connected.
- Reconnect the connector to its original position.
- Before disconnecting the connector, make a note of where it is connected.
Measure the resistance according to the value(s) in the table below.

- Standard resistance:
Tester Connection
Condition
Specified Condition
E10-6 (CANH) - E10-14 (CANL)
Ignition switch off
1 MΩ or higher
Reconnect the DLC3 branch wire connector (E62) to the No. 1 CAN J/C "B" side (without earth terminal).
|
|
||||
| OK | |
| 2. CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 CAN J/C SIDE) |
Disconnect the CAN main bus wire connector (E42) from the No. 1 CAN J/C "A" side (with earth terminal).

Connect the probes of an ohmmeter to terminals 6 (CANH) and 14 (CANL) of the DLC3.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
E10-6 (CANH) - E10-14 (CANL)
Ignition switch off
108 to 132 Ω
|
|
||||
| NG | |
| 3. CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 CAN J/C BRANCH WIRE) |
Reconnect the CAN main bus wire connector (E42) to the No. 1 CAN J/C "A" side (with earth terminal).

Connect the probes of an ohmmeter to terminals 6 (CANH) and 14 (CANL) of the DLC3.
While observing the resistance value shown on the tester, disconnect connectors E44, and E45 from the No. 1 CAN J/C one by one until the resistance becomes normal (between 54 and 69 Ω).
- HINT:
- Disconnect the branch wire connectors other than those of the DLC3.




No. 1 CAN J/C Connector ("A" side, with earth terminal)
Connector Color
Wire Color (CAN-H)
Wire Color (CAN-L)
Center Airbag Sensor Assembly (E45)
Black
B
W
No. 1 CAN J/C Connector ("B" side, without earth terminal)
Connector Color
Wire Color (CAN-H)
Wire Color (CAN-L)
Main Body ECU (E44)
Black
B
W
- NOTICE:
- Do not reconnect the disconnected connectors until this inspection is complete because there may be a short in 2 or more branch wires.
- Result:
Symptom
Proceed to
The resistance is still below 54 Ω when all the specified connectors are disconnected. (There are no shorts in the branch wires.)
A
The resistance becomes normal (between 54 and 69 Ω) when a connector is disconnected. (There is a short in one or more of the branch wires.)
B
When there is a short in one or more of the branch wires:
Reconnect all of the connectors to the No. 1 CAN J/C, except for the one that was disconnected last (the short-circuited bus wire). Check that the resistance shown on the tester is normal (between 54 and 69 Ω) to confirm that there is a short in one branch wire only.
- HINT:
- The connectors connected to the No. 1 CAN J/C can be distinguished according to the color of the communication bus wires and the shape of the connectors.
- Reconnecting the connectors to non-specified positions on the No. 1 CAN J/C does not affect system operation. However, it is preferred to reconnect the connectors to their specified positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.
- The connectors connected to the No. 1 CAN J/C can be distinguished according to the color of the communication bus wires and the shape of the connectors.
|
|
||||
| A | |
| 4. CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER MAIN BUS WIRE) |
Disconnect the combination meter main bus wire connector (E43) from the No. 1 CAN J/C "B" side (without earth terminal).

- NOTICE:
- Before disconnecting the connector, make a note of where it is connected.
- Reconnect the connector to its original position.
- Before disconnecting the connector, make a note of where it is connected.
Measure the resistance according to the value(s) in the table below.

- Standard resistance:
Tester Connection
Condition
Specified Condition
E10-6 (CANH) - E10-14 (CANL)
Ignition switch off
108 to 132 Ω
|
|
||||
| OK | |
| 5. RECONNECT CONNECTOR |
Reconnect the combination meter main bus wire connector (E43) to the No. 1 CAN J/C "B" side (with earth terminal).
| NEXT | |
| 6. CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER) |
Disconnect the combination meter connector (F1).

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
E10-6 (CANH) - E10-14 (CANL)
Ignition switch off
108 to 132 Ω
- HINT:
- If the resistance changes to 108 to 132 Ω when the connector is disconnected, there may be a short in the combination meter.
|
|
||||
| OK | ||
| ||
| 7. CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 CAN J/C - NO. 1 CAN J/C) |
Reconnect the No. 1 CAN J/C connector (E42).

Disconnect the No. 4 CAN J/C connector (E41).
Measure the resistance according to the value(s) in the table below.

- Standard resistance:
Tester Connection
Condition
Specified Condition
E10-6 (CANH) - E10-14 (CANL)
Ignition switch off
108 to 132 Ω
|
|
||||
| OK | |
| 8. CHECK FOR SHORT IN CAN BUS WIRES |
Reconnect the No. 4 CAN J/C connector (E41).

Disconnect the No. 4 CAN J/C connector (A40).
Measure the resistance according to the value(s) in the table below.

- Standard resistance:
Tester Connection
Condition
Specified Condition
E10-6 (CANH) - E10-14 (CANL)
Ignition switch off
108 to 132 Ω
|
|
||||
| NG | |
| 9. CHECK FOR SHORT IN CAN BUS WIRES (A/C AMPLIFIER BRANCH WIRE) |
Reconnect the No. 4 CAN J/C connector (A40).

Disconnect the No. 4 CAN J/C connector (E41).
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
E41-1 (CANH) - E41-7 (CANL)
Ignition switch off
1 MΩ or higher
|
|
||||
| OK | ||
| ||
| 10. CHECK FOR SHORT IN CAN BUS WIRES (A/C AMPLIFIER - NO. 4 CAN J/C) |
Disconnect the A/C amplifier connector (E38).

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
E41-1 (CANH) - E41-7 (CANL)
Ignition switch off
1 MΩ or higher
|
|
||||
| OK | ||
| ||
| 11. CHECK FOR SHORT IN CAN BUS WIRES (ECM MAIN BUS WIRE) |
Measure the resistance according to the value(s) in the table below.

- Standard resistance:
Tester Connection
Condition
Specified Condition
A40-1 (CANH) - A40-7 (CANL)
Ignition switch off
108 to 132 Ω
|
|
||||
| OK | |
| 12. CHECK FOR SHORT IN CAN BUS WIRES (SKID CONTROL ECU - NO. 4 CAN J/C) |
Disconnect the skid control ECU connector (A25).

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
A40-2 (CANH) - A40-8 (CANL)
Ignition switch off
1 MΩ or higher
- HINT:
- Measure the resistance with the No. 4 CAN J/C connector (A40) disconnected.
|
|
||||
| NG | ||
| ||
| 13. CHECK FOR SHORT IN CAN BUS WIRES (ECM MAIN BUS WIRE) |
Disconnect the ECM connector (A24 or A55).

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
A40-1 (CANH) - A40-7 (CANL)
Ignition switch off
1 MΩ or higher
- HINT:
- Measure the resistance with the No. 4 CAN J/C connector (A40) disconnected.
|
|
||||
| OK | ||
| ||
| 14. RECONNECT CONNECTOR |
Reconnect the connector for the short-circuited branch wire to the No. 1 CAN J/C (the connector that caused the bus wire resistance to become normal (between 54 and 69 Ω) when it was disconnected).
| NEXT | |
| 15. CHECK FOR SHORT IN CAN BUS WIRES |
Disconnect the connector that includes terminals CANH and CANL from the ECU (or sensor) to which the short-circuited branch wire is connected. (Click here)

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
E10-6 (CANH) - E10-14 (CANL)
Ignition switch off
54 to 69 Ω
- HINT:
- If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU (or sensor), there may be a short in the ECU (or sensor).
|
|
||||
| OK | ||
| ||
