2006-2011 Camry Aurion · Service Manual COMMUNICATION SYSTEM

Short to GND in CAN Bus Line

Circuit diagnosis · Vehicles built Oct 2006 – May 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

A short to GND is suspected in the CAN bus wire when the resistance between terminals 4 (CG) and 6 (CANH), or terminals 4 (CG) and 14 (CANL) of the DLC3 is below 200 Ω.
Symptoms
Trouble Area
The resistance between terminals 6 (CANH) and 4 (CG), or terminals 14 (CANL) and 4 (CG) of the DLC3 is below 200 Ω.
  1. Short to GND in CAN bus wire
  2. ECM
  3. Skid control ECU
  4. Steering angle sensor
  5. Yaw rate sensor
  6. Main body ECU
  7. A/C amplifier
  8. Center airbag sensor assembly
  9. Combination meter
  10. No. 1 CAN J/C

WIRING DIAGRAM

C133286E11
C142706E03

INSPECTION PROCEDURE

NOTICE:
  1. Turn the ignition switch off before measuring the resistances of CAN main wires and CAN branch wires.
  2. After the ignition switch is turned off, check that the key reminder warning system and lighting system are not operating.
  3. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If doors need to be opened in order to check connectors, open the doors and leave them open.

HINT:
Operating the ignition switch, any other switches, or any doors triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.


1. CHECK FOR SHORT TO GND IN CAN BUS WIRE (DLC3 BRANCH WIRE)

  1. C133246E24
    Turn the ignition switch off.

  1. Disconnect the DLC3 branch wire connector (E41) from the No. 4 CAN J/C (front of the vehicle).

  1. C126231E13
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E10-6 (CANH) - E10-4 (CG)
    Ignition switch off
    200 Ω or higher
    E10-14 (CANL) - E10-4 (CG)
    Ignition switch off
    200 Ω or higher

  1. Reconnect the DLC3 branch wire connector (E41) to the No. 4 CAN J/C (front of the vehicle).



NG
REPAIR OR REPLACE DLC3 BRANCH WIRE OR CONNECTOR
OK


2. CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 CAN J/C SIDE)

  1. C142742E05
    Disconnect the CAN main bus wire connector (E42) from the No. 1 CAN J/C "A" side (with earth terminal).

  1. C126231E13
    Using an ohmmeter, measure the resistance between terminals 6 (CANH) and 4 (CG), and between terminals 14 (CANL) and 4 (CG) of the DLC3 each time a connector is disconnected.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E10-6 (CANH) - E10-4 (CG)
    Ignition switch off
    200 Ω or higher
    E10-14 (CANL) - E10-4 (CG)
    Ignition switch off
    200 Ω or higher



NG
Go to step 6
OK


3. CHECK FOR SHORT TO GND IN CAN BUS WIRE

  1. C126231E13
    Reconnect the CAN main bus wire connector (E42).

  1. Disconnect connectors from the No. 1 CAN J/C one at a time.

  1. Using an ohmmeter, measure the resistance between terminals 6 (CANH) and 4 (CG), and between terminals 14 (CANL) and 4 (CG) of the DLC3 each time a connector is disconnected.C142793E02
    C145010E01

    No. 1 CAN J/C Connector ("A" side, with earth terminal)
    Connector Color
    Wire Color (CAN-H)
    Wire Color (CAN-L)
    Center Airbag Sensor Assembly (E45)
    Black
    B
    W
    No. 1 CAN J/C Connector ("B" side, without earth terminal)
    Connector Color
    Wire Color (CAN-H)
    Wire Color (CAN-L)
    Yaw Rate Sensor (E46)*
    Blue
    B
    W
    A/C Amplifier (E47)
    Gray
    B
    W
    Combination Meter (E43)
    White
    B
    W
    Main Body ECU (E44)
    Black
    B
    W
    *: with VSC

    NOTICE:
    Do not reconnect the disconnected connectors until this inspection is complete because there may be a short to GND in 2 or more CAN bus wires.

  1. When there is a short to GND in one or more of the bus wires that connect to an ECU (or sensor):

    1. Reconnect all of the connectors to the No. 1 CAN J/C, except for the one that was disconnected last (the bus wire that is shorted to GND). Check that the resistance shown on the tester is normal (200 Ω or more) to confirm that there is a short to GND in one branch wire only.

      HINT:
      1. The connectors connected to the No. 1 CAN J/C can be distinguished according to the color of the communication bus wires and the shape of the connectors.
      2. Reconnecting the connectors to non-specified positions on the No. 1 CAN J/C does not affect system operation. However, it is preferred to reconnect the connectors to their specified positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.


NEXT


4. RECONNECT CONNECTOR
  1. Reconnect the connector of the bus wire that is shorted to GND to the No. 1 CAN J/C (the connector that caused the bus wire resistance to change to 200 Ω or more when it was disconnected).


NEXT


5. CHECK FOR SHORT TO GND IN CAN BUS WIRE

  1. C126231E13
    Disconnect the connector that includes terminals CANH and CANL from the ECU (or sensor) to which the bus wire shorted to GND is connected (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E10-6 (CANH) - E10-4 (CG)
    Ignition switch off
    200 Ω or higher
    E10-14 (CANL) - E10-4 (CG)
    Ignition switch off
    200 Ω or higher

    HINT:
    If the resistance changes to 200 Ω or higher when the connector is disconnected from the ECU (or sensor), there may be a short in the ECU (or sensor).



NG
REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR BRANCH WIRE OR CONNECTOR
OK

REPLACE CORRESPONDING ECU OR SENSOR

6. CHECK FOR SHORT TO GND IN CAN BUS WIRE
  1. Reconnect the CAN main bus wire connector (E42) to the No. 1 CAN J/C "A" side (with earth terminal).

  1. C133245E17
    Disconnect the No. 4 CAN J/C connector (A40).

  1. C126231E13
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E10-6 (CANH) - E10-4 (CG)
    Ignition switch off
    200 Ω or higher
    E10-14 (CANL) - E10-4 (CG)
    Ignition switch off
    200 Ω or higher



OK
Go to step 10
NG


7. RECONNECT CONNECTOR
  1. Reconnect the No. 4 CAN J/C connector (A40).


NEXT


8. CHECK FOR SHORT TO GND IN CAN BUS WIRE (STEERING ANGLE SENSOR BRANCH WIRE)

  1. C133246E16
    Disconnect the No. 4 CAN J/C connector (E41).

  1. C126231E15
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E41-3 (CANH) - E10-4 (CG)
    Ignition switch off
    200 Ω or higher
    E41-9 (CANL) - E10-4 (CG)
    Ignition switch off
    200 Ω or higher



OK
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (NO. 1 CAN J/C - NO. 4 CAN J/C)
NG


9. CHECK FOR SHORT TO GND IN CAN BUS WIRE (STEERING ANGLE SENSOR)

  1. C133246E16
    Disconnect the steering angle sensor connector (E17).

  1. C126231E15
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E41-3 (CANH) - E10-4 (CG)
    Ignition switch off
    200 Ω or higher
    E41-9 (CANL) - E10-4 (CG)
    Ignition switch off
    200 Ω or higher



NG
REPAIR OR REPLACE STEERING ANGLE SENSOR BRANCH WIRE OR CONNECTOR
OK

REPLACE STEERING ANGLE SENSOR

10. CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECM MAIN BUS WIRE)

  1. C133245E22
    Disconnect the No. 4 CAN J/C connector (A40).

  1. C126231E15
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A40-1 (CANH) - E10-4 (CG)
    Ignition switch off
    200 Ω or higher
    A40-7 (CANL) - E10-4 (CG)
    Ignition switch off
    200 Ω or higher



OK
Go to step 12
NG


11. CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECM)

  1. C133245E22
    Disconnect the ECM connector (A24).

  1. C126231E15
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A40-1 (CANH) - E10-4 (CG)
    Ignition switch off
    200 Ω or higher
    A40-7 (CANL) - E10-4 (CG)
    Ignition switch off
    200 Ω or higher



NG
REPAIR OR REPLACE CAN BUS MAIN WIRE OR CONNECTOR (ECM - NO. 4 CAN J/C)
OK

REPLACE ECM

12. CHECK FOR SHORT TO GND IN CAN BUS WIRE (SKID CONTROL ECU)

  1. C133245E19
    Disconnect the skid control ECU connector (A25) or (A26).

  1. C126231E15
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A40-2 (CANH) - E10-4 (CG)
    Ignition switch off
    200 Ω or higher
    A40-8 (CANL) - E10-4 (CG)
    Ignition switch off
    200 Ω or higher



OK
REPLACE BRAKE ACTUATOR ASSEMBLY
NG

REPAIR OR REPLACE SKID CONTROL ECU BRANCH WIRE OR CONNECTOR


← Short to B+ in CAN Bus Line (from Jun 2009)Short to GND in CAN Bus Line (from Jun 2009) →