2006-2011 Camry Aurion · Service Manual BODY ELECTRICAL

Driver Side Door UNLOCK Detection Switch Circuit

Circuit diagnosis · Vehicles built from Jun 2006

DESCRIPTION

The driver's door unlock detection switch is built into the driver's door lock assembly. The switch turns on when the driver's door is unlocked and turns off when the door is locked.
The main body ECU is connected to the driver's door lock assembly via terminal LSWD and driver's door lock/unlock state signals are input to the main body ECU.
The main body ECU applies voltage to the door unlock detection switch via terminal LSWD. When the door unlock detection switch is on (there is continuity between the switch terminals), an unlock state signal is input to the main body ECU. When the switch is off (there is no continuity between the switch terminals), a lock state signal is input.

WIRING DIAGRAM

B109777E34

INSPECTION PROCEDURE


1. READ VALUE USING DATA LIST (DOOR UNLOCK DETECTION SWITCH)
  1. Check the DATA LIST to ensure proper function of the door unlock detection switch.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    D-Door Lock Pos SW
    Driver side door unlock detection switch signal/ON or OFF
    ON: Driver side door is unlocked
    OFF: Driver side door is locked
    -

    OK:
    The display is as specified in the normal condition column.



NG
Go to step 2
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

2. INSPECT FRONT DOOR LOCK ASSEMBLY (DOOR UNLOCK DETECTION SWITCH)

  1. B065427E23
    Inspect LHD models.
    1. Remove the front door lock assembly LH.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Measurement Condition
      Door Lock Condition
      Specified Condition
      7 - 8
      Battery positive (+) → Terminal 4
      Battery negative (-) → Terminal 1
      Lock
      10 kΩ or higher
      7 - 8
      Battery positive (+) → Terminal 1
      Battery negative (-) → Terminal 4
      Unlock
      Below 1 Ω

  1. B065429E22
    Inspect RHD models.
    1. Remove the front door lock assembly RH.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Measurement Condition
      Door Lock Condition
      Specified Condition
      7 - 8
      Battery positive (+) → Terminal 4
      Battery negative (-) → Terminal 1
      Lock
      10 kΩ or higher
      7 - 8
      Battery positive (+) → Terminal 1
      Battery negative (-) → Terminal 4
      Unlock
      Below 1 Ω



NG
REPLACE FRONT DOOR LOCK ASSEMBLY
OK


3. CHECK WIRE HARNESS (FRONT DOOR LOCK ASSEMBLY - MAIN BODY ECU)

  1. B112606E05
    Disconnect the front door lock assembly connector.

  1. Disconnect the main body ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    (Symbols)
    Condition
    Specified Condition
    (*1) I7-8 (LSSR) - E7-9 (LSWD)
    Always
    Below 1 Ω
    (*1) I7-8 (LSSR) - Body ground
    Always
    10 kΩ or higher
    (*1) I7-7 (E) - Body ground
    Always
    Below 1 Ω
    (*2) H8-7 (LSSR) - E7-9 (LSWD)
    Always
    Below 1 Ω
    (*2) H8-7 (LSSR) - Body ground
    Always
    10 kΩ or higher
    (*2) H8-8 (E) - Body ground
    Always
    Below 1 Ω

    *1: LHD*2: RHD



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU


← DATA LIST / ACTIVE TEST (from Jun 2009)Front Passenger Side Door UNLOCK Detection Switch Circuit (from Jun 2006) →