2006-2011 Camry Aurion · Service Manual BODY ELECTRICAL

Front Passenger Side Door UNLOCK Detection Switch Circuit

Circuit diagnosis · Vehicles built from Jun 2006

DESCRIPTION

The front passenger door unlock detection switch is built into the front passenger door lock assembly. The switch turns on when the front passenger door is unlocked and turns off when the door is locked.
The main body ECU is connected to the front passenger door lock assembly via terminal LSWP and front passenger door lock/unlock state signals are input to the ECU.
The main body ECU applies voltage to the door unlock detection switch via terminal LSWP. When the door unlock detection switch is on (there is continuity between the switch terminals), an unlock state signal is input to the ECU. When the switch is off (there is no continuity between the switch terminals), a lock state signal is input.

WIRING DIAGRAM

B109773E49

INSPECTION PROCEDURE


1. READ VALUE USING DATA LIST (DOOR UNLOCK DETECTION SWITCH)
  1. Check the DATA LIST to ensure proper function of the door unlock detection switch.

    HINT:
    When the rear left door or rear right door is unlocked, the LSWP terminal will be ON. In this case, perform the inspection with the other doors locked.

    Main Body: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    P-Door Lock Pos SW
    Passenger side door lock position switch signal/ON or OFF
    ON: Passenger side door lock is in UNLOCK position
    OFF: Passenger side door lock is in LOCK position
    -

    OK:
    The display is as specified in the normal condition column.



NG
Go to step 2
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

2. INSPECT FRONT DOOR LOCK ASSEMBLY (DOOR UNLOCK DETECTION SWITCH)

  1. B065429E23
    Inspect LHD models.
    1. Remove the front door lock assembly RH.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Measurement Condition
      Door Lock Condition
      Specified Condition
      7 - 8
      Battery positive (+) → Terminal 4
      Battery negative (-) → Terminal 1
      Lock
      10 kΩ or higher
      7 - 8
      Battery positive (+) → Terminal 1
      Battery negative (-) → Terminal 4
      Unlock
      Below 1 Ω

  1. B065427E22
    Inspect RHD models.
    1. Remove the front door lock assembly LH.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Measurement Condition
      Door Lock Condition
      Specified Condition
      7 - 8
      Battery positive (+) → Terminal 4
      Battery negative (-) → Terminal 1
      Lock
      10 kΩ or higher
      7 - 8
      Battery positive (+) → Terminal 1
      Battery negative (-) → Terminal 4
      Unlock
      Below 1 Ω



NG
REPLACE FRONT DOOR LOCK ASSEMBLY
OK


3. CHECK WIRE HARNESS (FRONT DOOR LOCK ASSEMBLY - MAIN BODY ECU)

  1. B111708E21
    Disconnect the front door lock assembly connector.

  1. Disconnect the ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    (Symbols)
    Condition
    Specified Condition
    (*1) H8-7 (LSSR) - E6-27 (LSWP)
    Always
    Below 1 Ω
    (*1) H8-7 (LSSR) - Body ground
    Always
    10 kΩ or higher
    (*1) H8-8 (E) - Body ground
    Always
    Below 1 Ω
    (*2) I7-8 (LSSR) - E6-27 (LSWP)
    Always
    Below 1 Ω
    (*2) I7-8 (LSSR) - Body ground
    Always
    10 kΩ or higher
    (*2) I7-7 (E) - Body ground
    Always
    Below 1 Ω

    *1: LHD*2: RHD



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU


← Driver Side Door UNLOCK Detection Switch Circuit (from Jun 2006)Rear Door UNLOCK Detection Switch LH Circuit (Jun 2006 – May 2009) →