INSPECTION
Inspection · Vehicles built Jun 2006 – Sep 2006
Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009
| INSPECT TIRES |
Check the tires for wear and proper inflation pressure.
- Cold tire inflation pressure:
for Australia: Tire size
Front kPa (kgf*cm2, psi)
Rear kPa (kgf*cm2, psi)
215/60R16 95V
4 passengers or less
210 (2.1, 31)*1, 230 (2.3, 33)*2
210 (2.1, 31)*1, 230 (2.3, 33)*2
5 passengers
240 (2.4, 35)*1, 300 (3.1, 44)*2
240 (2.4, 35)*1, 300 (3.1, 44)*2
215/55R17 93V
4 passengers or less
220 (2.2, 32)*1, 250 (2.5, 36)*2
220 (2.2, 32)*1, 250 (2.5, 36)*2
5 passengers
240 (2.4, 35)*1, 300 (3.1, 44)*2
240 (2.4, 35)*1, 300 (3.1, 44)*2
*2: For driving at over 140 km/h (87 mph).- Cold tire inflation pressure:
for GCC: Tire size
Front kPa (kgf*cm2, psi)
Rear kPa (kgf*cm2, psi)
215/60R16 95V
210 (2.1, 31)*1, 240 (2.4, 35)*2
210 (2.1, 31)*1, 240 (2.4, 35)*2
215/55R17 93V
220 (2.2, 32)*1, 240 (2.4, 35)*2
220 (2.2, 32)*1, 240 (2.4, 35)*2
*2: For driving at over 160 km/h (100 mph).
Using a dial indicator, check the runout of the tires.

- Tire runout:
- 1.4 mm (0.055 in.) or less
| ROTATE TIRES |
Rotate the tires as shown in the illustration.

| INSPECT WHEEL BALANCE |
Check and adjust the off-the-car balance.
Steel wheel

- Imbalance after adjustment:
- 8.0 g (0.018 lb.) or less
- HINT:
- If necessary, check and adjust the on-the-car balance.
Others (Non-steel wheel)

- Imbalance after adjustment:
- 8.0 g (0.018 lb.) or less
- NOTICE:
- Use a cleaning detergent to remove dirt, oil, and water from the surface where the balance weight attaches.
- Do not touch the adhesive surface of the tape.
- Attach the adhesive type balance weight to the flat position shown in the illustration.
- Push the balance weight securely with a finger to adhere it to the position.
- Do not reuse the balance weight.
- Use a cleaning detergent to remove dirt, oil, and water from the surface where the balance weight attaches.
- HINT:
- Inner side balance weight should be installed by clipping it to the rim.
- If necessary, check and adjust the on-the-car balance.
- Inner side balance weight should be installed by clipping it to the rim.
| INSPECT FRONT AXLE HUB BEARING LOOSENESS |
- HINT:
- (Click here)
| INSPECT REAR AXLE HUB BEARING LOOSENESS |
- HINT:
- (Click here)
| INSPECT FRONT AXLE HUB RUNOUT |
- HINT:
- (Click here)
| INSPECT REAR AXLE HUB RUNOUT |
- HINT:
- (Click here)
