B2284 Brake Signal Malfunction
Diagnostic trouble codes · Vehicles built from Jun 2009
Versions by build date: Oct 2006 – May 2009 from Jun 2009
DESCRIPTION
- HINT:
- When the main body ECU is replaced with a new one and the negative (-) battery terminal is connected, the power source mode becomes the IG-ON mode. When the battery is removed and reinstalled, the power source mode that was selected when the battery was removed is restored.
- After the main body ECU is replaced, perform the registration procedures for the engine immobiliser system.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| B2284 |
The brake signal circuit between the main body ECU and the stop light switch is malfunctioning and the CAN information is inconsistent |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
| EMERGENCY ENGINE START CONTROL |
If there is a malfunction in the stop light switch or STOP fuse, their signals may not be correctly transmitted to the main body ECU. This may result in the engine not starting even if the engine switch is pressed while the brake pedal is depressed and the shift lever is in the P position.
To activate the starter:Turn the engine switch from off to on (ACC).
Press and hold the engine switch for 15 seconds.
- HINT:
- Before performing the inspection, depress the brake pedal and check that the stop lights come on. If the stop lights do not come on when the brake pedal is depressed, refer to the page shown in the brackets (Click here).
| 1. READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Check the DATA LIST for proper functioning of the stop light switch.
Body: Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Stop Light SW
Stop light switch/ON or OFF
ON: Brake pedal depressed
OFF: Brake pedal released
-
- OK:
- ON (brake pedal depressed) and OFF (brake pedal released) appear on the screen.
|
|
||||
| OK | |
| 2. CHECK DTC OUTPUT (CAN COMMUNICATION SYSTEM) |
Delete the DTCs (Click here).
Check for CAN communication system DTCs (for LHD: Click here), (for RHD: Click here).
- HINT:
- If the DTCs for the CAN communication system malfunction are output, inspect those DTCs first (for LHD: Click here), (for RHD: Click here).
- OK:
- No DTC is output.
|
|
||||
| OK | |
| 3. CHECK DTC OUTPUT (ENGINE CONTROL SYSTEM) |
Delete the DTCs (Click here).
Check for DTC P0500 (Vehicle speed sensor A) (Click here).
- OK:
- No DTC is output.
|
|
||||
| OK | ||
| ||
| 4. INSPECT FUSE (STOP) |
Remove the STOP fuse from the instrument panel J/B.
Measure the resistance of the fuse.
- Standard resistance:
- Below 1 Ω
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (STOP FUSE - STOP LIGHT SWITCH) |
Disconnect the A79 switch connector.

Measure the voltage according to the value(s) in the table below.
- Standard voltage:
Tester Connection
Condition
Specified Condition
A79-2 - Body ground
Always
11 to 14 V
|
|
||||
| OK | |
| 6. INSPECT STOP LIGHT SWITCH |
Remove the switch.

Measure the resistance of the switch.
- Standard resistance:
Tester Connection
Switch Condition
Specified Condition
1 - 2
Switch pin free
Below 1 Ω
3 - 4
Switch pin free
10 kΩ or higher
1 - 2
Switch pin pushed in
10 kΩ or higher
3 - 4
Switch pin pushed in
Below 1 Ω
|
|
||||
| OK | |
| 7. CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH - MAIN BODY ECU) |
Disconnect IL instrument panel junction block connector.


Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
A79-1 - IL-7
Always
Below 1 Ω
A79-1 - Body ground
10 kΩ or higher
|
|
||||
| OK | ||
| ||
