P0500 Vehicle Speed Sensor "A"
Diagnostic trouble codes · Vehicles built from Jun 2009
Versions by build date: Oct 2006 – May 2009 from Jun 2009
DESCRIPTION
The speed sensor detects the wheel speed and sends the appropriate signals to the skid control ECU. The skid control ECU converts these wheel speed signals into a 4-pulse signal and outputs it to the ECM via the combination meter. The ECM determines the vehicle speed based on the frequency of these pulse signals.- HINT:
- A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter. The signal is changed to pulse signal at the transistor in the combination meter. Each ECU controls the respective system based on the pulse signal.
- If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the diagram below will not operate normally.
- A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter. The signal is changed to pulse signal at the transistor in the combination meter. Each ECU controls the respective system based on the pulse signal.


| DTC No. |
DTC Detection Condition |
Trouble Area |
| P0500 |
Vehicle speed signal from vehicle speed sensor is cut for 0.14 sec. or more while cruise control is in operation. |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- Read freeze frame data using the intelligent tester or the OBD II scan tool. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction (Click here).
| 1. READ VALUE USING INTELLIGENT TESTER (VEHICLE SPEED) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Turn the tester on.
Select the following menu items: Powertrain / Engine / Date List / Vehicle Speed.
Drive the vehicle.
Read the value displayed on the tester.
- OK:
- Vehicle speeds displayed on tester and speedometer display are equal.
|
|
||||
| OK | ||
| ||
| 2. CHECK COMBINATION METER SYSTEM |
The circuits that send vehicle speed signals to this system are inspected in the meter system (Click here).
During inspection for the meter section, if there is an instruction that indicates to go back inspections for each system, proceed to the next step.
| NEXT | |
| 3. CHECK HARNESS AND CONNECTOR (ECM - COMBINATION METER) |
Disconnect the A24 (RHD) or A55 (LHD) ECM connector.

Disconnect the F2 combination meter connector.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
- RHD
Tester Connection
Specified Condition
SPD (A24-8) - +S (F2-12)
Below 1 Ω
- LHD
Tester Connection
Specified Condition
SPD (A55-8) - +S (F2-12)
Below 1 Ω
Reconnect the ECM connector.
Reconnect the combination meter connector.
|
|
||||
| OK | ||
| ||
| 4. CHECK HARNESS AND CONNECTOR (ECM - NO. 3 JUNCTION BLOCK) |
Disconnect the A24 (RHD) or A55 (LHD) ECM connector.


Disconnect the 3B No. 3 junction block connector.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
- RHD
Tester Connection
Specified Condition
3B-10 - SPD (A24-8)
Below 1 Ω
- LHD
Tester Connection
Specified Condition
3B-10 - SPD (A55-8)
Below 1 Ω
Reconnect the ECM connector.
Reconnect the No. 3 junction block connector.
|
|
||||
| OK | ||
| ||
