P0351 Ignition Coil "A" Primary / Secondary Circuit
Diagnostic trouble codes · Vehicles built Jun 2006 – Sep 2006
Also covers:
- P0352 Ignition Coil "B" Primary / Secondary Circuit
- P0353 Ignition Coil "C" Primary / Secondary Circuit
- P0354 Ignition Coil "D" Primary / Secondary Circuit
Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009
DESCRIPTION
- HINT:
- These DTCs indicate malfunctions relating to the primary circuit.
- If DTC P0351 is set, check the ignition No. 1 coil circuit.
- If DTC P0352 is set, check the ignition No. 2 coil circuit.
- If DTC P0353 is set, check the ignition No. 3 coil circuit.
- If DTC P0354 is set, check the ignition No. 4 coil circuit.
- These DTCs indicate malfunctions relating to the primary circuit.
The DIS is a 1-cylinder ignition system in which each cylinder is ignited by one ignition coil and one spark plug is connected to the end of each secondary wiring. A powerful voltage, generated in the secondary wiring, is applied directly to each spark plug. Then, a spark passes from the center electrode to the ground electrodes.
The ECM determines the ignition timing and transmits the ignition (IGT) signals to each cylinder. Using the IGT signal, the ECM turns the power transistor inside the igniter on and off. The power transistor, in turn, switches on and off the current to the primary coil. When the current to the primary coil is cut off, a powerful voltage is generated in the secondary coil. This voltage is applied to the spark plugs, causing them to spark inside the cylinders. As the ECM cuts the current to the primary coil off, the igniter sends back an ignition confirmation (IGF) signal to the ECM, for each cylinder ignition.


| DTC No. |
DTC Detection Condition |
Trouble Area |
| P0351 P0352 P0353 P0354 |
No IGF signal to ECM while engine is running (1-trip detection logic) |
|
-


- Reference: Inspection using an oscilloscope.
- While cranking or idling the engine, check the waveform between terminals IGT (1 to 4) and E1, and IGF1 and E1 of the ECM connector.
Item
Content
Terminals
CH1: IGT1, IGT2, IGT3, IGT4 - E1
CH2: IGF1 - E1
Equipment Settings
2 V/DIV.
20 ms./DIV.
Conditions
Cranking or idling
WIRING DIAGRAM




INSPECTION PROCEDURE
- HINT:
- Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
| 1. INSPECT IGNITION COIL ASSEMBLY (POWER SOURCE) |
Disconnect the C11 to C14 ignition coil connectors.

Measure the resistance according to the value(s) in the table below.
- Standard resistance (Check for open):
Tester Connection
Specified Condition
GND (C11-4) - Body ground
Below 1 Ω
GND (C13-4) - Body ground
GND (C12-4) - Body ground
GND (C14-4) - Body ground
Turn the ignition switch to the ON position.
Measure the voltage between the terminals of the wire harness side connectors.
- Standard voltage:
Tester Connection
Specified Condition
+B (C11-1) - GND (C11-4)
9 to 14 V
+B (C13-1) - GND (C13-4)
+B (C12-1) - GND (C12-4)
+B (C14-1) - GND (C14-4)
Reconnect the ignition coil connectors.
|
|
||||
| OK | |
| 2. CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM) |
Disconnect the C11 to C14 ignition coil connectors.

Disconnect the C24 ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard resistance (Check for open):
Tester Connection
Specified Condition
IGF (C11-2) - IGF1 (C24-81)
Below 1 Ω
IGF (C13-2) - IGF1 (C24-81)
IGF (C12-2) - IGF1 (C24-81)
IGF (C14-2) - IGF1 (C24-81)
- Standard resistance (Check for open):
Tester Connection
Specified Condition
IGT1 (C11-3) - IGT1 (C24-85)
Below 1 Ω
IGT2 (C13-3) - IGT2 (C24-84)
IGT3 (C12-3) - IGT3 (C24-83)
IGT4 (C14-3) - IGT4 (C24-82)
- Standard resistance (Check for short):
Tester Connection
Specified Condition
IGF (C11-2) or IGF1 (C24-81) - Body ground
10 kΩ or higher
IGF (C13-2) or IGF1 (C24-81) - Body ground
IGF (C12-2) or IGF1 (C24-81) - Body ground
IGF (C14-2) or IGF1 (C24-81) - Body ground
- Standard resistance (Check for short):
Tester Connection
Specified Condition
IGT1 (C11-3) or IGT1 (C24-85) - Body ground
10 kΩ or higher
IGT2 (C13-3) or IGT2 (C24-84) - Body ground
IGT3 (C12-3) or IGT3 (C24-83) - Body ground
IGT4 (C14-3) or IGT4 (C24-82) - Body ground
Reconnect the ECM connector.
Reconnect the ignition coil connectors.
|
|
||||
| OK | |
| 3. CHECK WHETHER DTC OUTPUT RECURS (DTC P0351, P0352, P0353 OR P0354) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position and turn the tester on.
Clear the DTCs (Click here).
Shuffle arrangement of the ignition coils with igniters (among No. 1 to No. 4 cylinders).
- NOTICE:
- Do not shuffle the connectors.
Perform a simulation test.
Check the DTCs displayed on the tester.
- Result:
Display (DTC Output)
Proceed to
Same DTC output
A
Different ignition coil DTC output
B
|
|
||||
| A | ||
| ||
