2006-2011 Camry Aurion · Service Manual ENGINE

P0340 Camshaft Position Sensor "A" Circuit (Bank 1 or Single Sensor)

Diagnostic trouble codes · Vehicles built from Jun 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

The Camshaft Position (CMP) sensor consists of a magnet and an iron core which is wrapped with copper wire, and is installed onto the cylinder head. When the camshaft rotates, each of 3 teeth on the camshaft passes through the CMP sensor. This activates the internal magnet in the sensor, generating a voltage in the copper wire. The camshaft rotation is synchronized with the crankshaft rotation. When the crankshaft turns twice, the voltage is generated 3 times in the CMP sensor. The generated voltage in the sensor acts as a signal, allowing the ECM to locate the camshaft position. This signal is then used to control ignition timing, fuel injection timing, and the VVT system.
DTC No.
DTC Detection Condition
Trouble Area
P0340
Case 1
  1. No Camshaft Position (CMP) sensor signal to ECM while cranking (2-trip detection logic)
Case 2
  1. Camshaft/Crankshaft misalignment is detected at engine speed of 600 rpm or more (1-trip detection logic)
  1. Open or short in CMP sensor circuit
  2. CMP sensor
  3. Camshaft
  4. Jumped tooth of timing chain
  5. ECM

HINT:
DTC P0340 indicates a malfunction relating to the CMP sensor (+) circuit (the wire harness between the ECM and CMP sensor, and the CMP sensor itself).

Reference: Inspection using an oscilloscope
A063955E21

HINT:
  1. The correct waveform is as shown in the illustration.
  2. G2+ stands for the CMP sensor signal, and NE+ stands for the Crankshaft Position (CKP) sensor signal.
  3. Grounding failure of the shielded wire may cause noise in waveforms.
Item
Content
Terminals
CH1: G2+ - G2-
CH2: NE+ - NE-
Equipment Settings
5 V/DIV.
20 ms./DIV.
Conditions
Cranking or idling


WIRING DIAGRAM

Refer to DTC P0335 (Click here).

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. INSPECT CAMSHAFT POSITION SENSOR (RESISTANCE)

  1. G037727E03
    Disconnect the C31 Camshaft Position (CMP) sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    1 - 2
    950 to 1,250 Ω (at 20°C (68°F))

  1. Reconnect the CMP sensor connector.



NG
REPLACE CAMSHAFT POSITION SENSOR
OK


2. CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)

  1. A106885E06
    Disconnect the C31 CMP sensor connector.

  1. Disconnect the C24 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    G2+ (C31-1) - G2+ (C24-99)
    Below 1 Ω
    G2- (C31-2) - G2- (C24-98)

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    G2+ (C31-1) or G2+ (C24-99) - Body ground
    10 kΩ or higher
    G2- (C31-2) or G2- (C24-98) - Body ground

  1. Reconnect the ECM connector.

  1. Reconnect the CMP sensor connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK SENSOR INSTALLATION (CAMSHAFT POSITION SENSOR)

  1. BR03795E25
    Check the CMP sensor installation condition.

    OK:
    Sensor is installed correctly.



NG
SECURELY REINSTALL CAMSHAFT POSITION SENSOR
OK


4. CHECK VALVE TIMING

  1. A098345E12
    Remove the cylinder head cover.

  1. Turn the crankshaft pulley, and align its groove with the timing mark "0" on the timing chain cover.

  1. Check that the timing marks on the camshaft timing sprocket and camshaft timing gear are facing upward as shown in the illustration.

    1. If not, turn the crankshaft 1 revolution (360°), then align the marks as above.

    OK:
    The timing marks on the camshaft timing gears are aligned as shown in the illustration.

  1. Reinstall the cylinder head cover.



NG
ADJUST VALVE TIMING
OK


5. CHECK CAMSHAFT
  1. Check the teeth of the camshaft.

    OK:
    Camshaft teeth do not have any cracks or deformation.



NG
REPLACE CAMSHAFT
OK


6. REPLACE CAMSHAFT POSITION SENSOR

NEXT


7. CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to on (IG) and turn the tester on.

  1. Clear the DTCs (Click here).

  1. Start the engine.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result:
    Display (DTC Output)
    Proceed to
    No output
    A
    P0340
    B

HINT:
If the engine does not start, replace the ECM.



B
REPLACE ECM
A

END


← P0340 Camshaft Position Sensor "A" Circuit (Bank 1 or Single Sensor) (Oct 2006 – May 2009)P0351 Ignition Coil "A" Primary / Secondary Circuit (+ P0352, P0353, P0354) (Jun 2006 – Sep 2006) →