P0013 Camshaft Position "B" Actuator Circuit / Open (Bank 1)
Diagnostic trouble codes · Vehicles built from Jun 2009
Also covers:
- P0023 Camshaft Position "B" Actuator Circuit / Open (Bank 2)
Versions by build date: Oct 2006 – May 2009 from Jun 2009
DESCRIPTION
The Variable Valve Timing (VVT) system includes the ECM, OCV and VVT controller. The ECM sends a target duty-cycle control signal to the OCV. This control signal regulates the oil pressure supplied to the VVT controller. Camshaft timing control is performed according to engine operating conditions such as the intake air volume, throttle valve position and engine coolant temperature. The ECM controls the OCV, based on the signals transmitted by several sensors. The VVT controller regulates the exhaust camshaft angle using oil pressure through the OCV. As a result, the relative positions of the camshaft and crankshaft are optimized, the engine torque and fuel economy improve, and the exhaust emissions decrease under overall driving conditions. The ECM detects the actual exhaust valve timing using signals from the camshaft and crankshaft position sensors, and performs feedback control. This is how the target intake valve timing is verified by the ECM.

| DTC No. |
DTC Detection Condition |
Trouble Area |
| P0013 |
Open or short in OCV for exhaust camshaft (bank 1) circuit (1 trip detection logic) |
|
| P0023 |
Open or short in OCV for exhaust camshaft (bank 2) circuit (1 trip detection logic) |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- If DTC P0013 is displayed, check the exhaust camshaft circuit for the bank 1 VVT system.
- Bank 1 refers to the bank that includes cylinder No. 1.
- If DTC P0023 is displayed, check the exhaust camshaft circuit for the bank 2 VVT system.
- Bank 2 refers to the bank that does not include cylinder No. 1.
- Read freeze frame data using an intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction (Click here).
- If DTC P0013 is displayed, check the exhaust camshaft circuit for the bank 1 VVT system.
| 1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (OPERATE OCV) |
Connect the intelligent tester to the DLC3.
Start the engine and turn the tester on.
Warm up the engine.
Enter the following menus: Powertrain / Engine / Active Test / Control the VVT System (Bank 1) or Control the VVT System (Bank 2).
Check the engine speed while operating the Oil Control Valve (OCV) using the tester.
- OK:
Tester Operation
Specified Condition
OCV OFF
Normal engine speed
OCV ON
Engine idles roughly or stalls (soon after OCV switched from OFF to ON)
|
|
||||
| OK | ||
| ||
| 2. INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY |
Disconnect the C42 or C46 OCV connector.

Measure the resistance between the terminals of the OCV.
- Standard resistance:
Tester Connection
Condition
Specified Condition
1 - 2
20°C (68°F)
6.9 to 7.9 Ω
Reconnect the OCV connector.
|
|
||||
| OK | |
| 3. CHECK HARNESS AND CONNECTOR (OCV - ECM) |
Disconnect the C42 or C46 OCV connector.

Disconnect the C58 (RHD) or C55 (LHD) ECM connector.
Measure the resistance between the terminals.
- Standard resistance (Check for open):
- RHD:
Tester Connection
Specified Condition
OE1+ (C58-16) - C42-1
Below 1 Ω
OE1- (C58-17) - C42-2
Below 1 Ω
OE2+ (C58-14) - C46-1
Below 1 Ω
OE2- (C58-15) - C46-2
Below 1 Ω
- LHD:
Tester Connection
Specified Condition
OE1+ (C55-16) - C42-1
Below 1 Ω
OE1- (C55-17) - C42-2
Below 1 Ω
OE2+ (C55-14) - C46-1
Below 1 Ω
OE2- (C55-15) - C46-2
Below 1 Ω
- Standard resistance (Check for short):
- RHD:
Tester Connection
Specified Condition
OE1+ (C58-16) or C42-1 - Body ground
10 kΩ or higher
OE1- (C58-17) or C42-2 - Body ground
10 kΩ or higher
OE2+ (C58-14) or C46-1 - Body ground
10 kΩ or higher
OE2- (C58-15) or C46-2 - Body ground
10 kΩ or higher
- LHD:
Tester Connection
Specified Condition
OE1+ (C55-16) or C42-1 - Body ground
10 kΩ or higher
OE1- (C55-17) or C42-2 - Body ground
10 kΩ or higher
OE2+ (C55-14) or C46-1 - Body ground
10 kΩ or higher
OE2- (C55-15) or C46-2 - Body ground
10 kΩ or higher
Reconnect the ECM connector.
Reconnect the OCV connector.
|
|
||||
| OK | ||
| ||
