2006-2011 Camry Aurion · Service Manual ENGINE

P2237 Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 1 Sensor 1)

Diagnostic trouble codes · Vehicles built from Jun 2009

Also covers:

DESCRIPTION

HINT:
  1. Although the DTC titles include oxygen sensor, these DTCs relate to the Air-Fuel Ratio (A/F) sensor.
  2. Sensor 1 refers to the sensor mounted in front of the Three-Way Catalytic Converter (TWC) and located near the engine assembly.

The A/F sensor generates voltage* that corresponds to the actual air-fuel ratio. This sensor voltage is used to provide the ECM with feedback so that it can control the air-fuel ratio. The ECM determines the deviation from the stoichiometric air-fuel ratio level, and regulates the fuel injection time. If the A/F sensor malfunctions, the ECM is unable to control the air-fuel ratio accurately.
The A/F sensor is the planar type and is integrated with the heater, which heats the solid electrolyte (zirconia element). This heater is controlled by the ECM. When the intake air volume is low (the exhaust gas temperature is low), a current flows into the heater to heat the sensor, in order to facilitate accurate oxygen concentration detection. In addition, the sensor and heater portions are narrower than the conventional type. The heat generated by the heater is conducted to the solid electrolyte through the alumina, therefore the sensor activation is accelerated.
A three-way catalytic converter (TWC) is used in order to convert the carbon monoxide (CO), hydrocarbon (HC), and nitrogen oxide (NOx) into less harmful substances. To allow the TWC to function effectively, it is necessary to keep the air-fuel ratio of the engine near the stoichiometric air-fuel ratio.
*: Value changes inside the ECM. Since the A/F sensor is the current output element, a current is converted to a voltage inside the ECM. Any measurements taken at the A/F sensor or ECM connectors will show a constant voltage.
A173183E21
DTC No.
DTC Detection Condition
Trouble Area
P2237
P2240
Open in the circuit between terminals A1A+ (A2A+) and A1A- (A2A-) of the air fuel ratio sensor while engine running.
(2 trip detection logic)
  1. Open or short in air fuel ratio sensor (bank 1, 2 sensor 1) circuit
  2. A/F sensor (bank 1, 2 sensor 1)
  3. ECM
P2238
P2241
  1. Case 1:
Condition (a) or (b) continues for 5.0 seconds or more
(1 trip detection logic):
(a) A1A+ (A2A+) voltage is 0.5 V or less
(b) A1A+ (A2A+) - A1A- (A2A-) = 0.1 V or less
  1. Case 2:
A/F sensor admittance: Less than 0.022 1/Ω
(2 trip detection logic)
  1. Open or short in A/F sensor (bank 1, 2 sensor 1) circuit
  2. A/F sensor (bank 1, 2 sensor 1)
  3. A/F sensor heater
  4. A/F relay
  5. A/F sensor heater and relay circuits
  6. ECM
P2239
P2242
A1A+ (A2A+) voltage is more than 4.5 V for 5.0 seconds or more
(2 trip detection logic)
  1. Open or short in A/F sensor (bank 1, 2 sensor 1) circuit
  2. A/F sensor (bank 1, 2 sensor 1)
  3. A/F sensor heater
  4. A/F relay
  5. A/F sensor heater and relay circuits
  6. ECM
P2252
P2255
A1A- (A2A-) voltage is 0.5 V or less for 5.0 seconds or more
(2 trip detection logic)
  1. Open or short in A/F sensor (bank 1, 2 sensor 1) circuit
  2. A/F sensor (bank 1, 2 sensor 1)
  3. A/F sensor heater
  4. A/F relay
  5. A/F sensor heater and relay circuits
  6. ECM
P2253
P2256
A1A- (A2A-) voltage is more than 4.5 V for 5.0 seconds or more
(2 trip detection logic)
  1. Open or short in A/F sensor (bank 1, 2 sensor 1) circuit
  2. A/F sensor (bank 1, 2 sensor 1)
  3. A/F sensor heater
  4. A/F relay
  5. A/F sensor heater and relay circuits
  6. ECM

HINT:
  1. DTCsP2237, P2238, P2239, P2252 and P2253 indicate malfunctions related to the bank 1 A/F sensor circuit.
  2. DTCs P2240, P2241, P2242, P2255 and P2256 indicate malfunctions related to the bank 2 A/F sensor circuit.
  3. Bank 1 refers to the bank that includes cylinder No. 1.
  4. Bank 2 refers to the bank that includes cylinder No. 2.


WIRING DIAGRAM

Refer to DTC P2195 (Click here).

INSPECTION PROCEDURE

HINT:
Intelligent tester only:
Malfunctioning areas can be identified by performing "Control the Injection Volume for A/F Sensor" provided in the Active Test. "Control the Injection Volume for A/F Sensor" can help to determine whether the Air-Fuel Ratio (A/F) sensor, Heated Oxygen (HO2) sensor and other potential trouble areas are malfunctioning.

The following instructions describe how to conduct "Control the Injection Volume for A/F Sensor" operation using the intelligent tester.
  1. Connect the intelligent tester to the DLC3.
  2. Start the engine and turn the tester on.
  3. Warm up the engine at an engine speed of 2,500 rpm for approximately 90 seconds.
  4. On the tester, enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume for A/F Sensor.
  5. Perform "Control the Injection Volume for A/F Sensor" with the engine in an idling condition (press the RIGHT or LEFT button to change the fuel injection volume).
  6. Monitor the output voltages of the A/F and HO2 sensors (AFS Voltage B1 S1 and O2S B1 S2 or AFS Voltage B2 S1 and O2S B2 S2) displayed on the tester.

HINT:
  1. "Control the Injection Volume for A/F Sensor" lowers the fuel injection volume by 12.5% or increases the injection volume by 25%.
  2. Each sensor reacts in accordance with increases and decreases in the fuel injection volume.

Tester Display
(Sensor)
Injection Volume
Status
Voltage
AFS Voltage B1S1 or AFS Voltage B2S1
(A/F)
+25%
Rich
Less than 3.1 V
AFS Voltage B1S1 or AFS Voltage B2S1
(A/F)
-12.5%
Lean
More than 3.4 V
O2S B1S2 or O2S B2S2
(HO2)
+25%
Rich
More than 0.55 V
O2S B1S2 or O2S B2S2
(HO2)
-12.5%
Lean
Less than 0.4 V

NOTICE:
The Air-Fuel Ratio (A/F) sensor has an output delay of a few seconds and the Heated Oxygen (HO2) sensor has a maximum output delay of approximately 20 seconds.

Case
Air Fuel Ratio Sensor (Sensor 1)
Output Voltage
Heated Oxygen Sensor (Sensor 2)
Output Voltage
Main Suspected Trouble Area
1
A162605E12
A162598E12
-
2
A162596E06
A162598E12
  1. Air fuel ratio sensor
  2. Air fuel ratio sensor heater
  3. Air fuel ratio sensor circuit
3
A162605E12
A162596E07
  1. Heated oxygen sensor
  2. Heated oxygen sensor heater
  3. Heated oxygen sensor circuit
  4. Exhaust gas leaks
4
A162596E06
A162596E06
  1. Fuel pressure
  2. Exhaust gas leaks
    (Air fuel ratio extremely lean or rich)
  1. Performing "Control the Injection Volume for A/F Sensor" enables technicians to check and graph the output voltages of both the A/F and HO2 sensors.
  2. The following A/F Control procedure enables the technician to check and graph the voltage output of both the heated oxygen sensors. To display the graph, select the following menu item on the tester: View Line/Graph.

HINT:
  1. Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction (Click here).


1. INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)

  1. A140627E04
    Disconnect the C15 or C35 A/F sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Bank 1 sensor 1:
    Tester Connection
    Condition
    Specified Condition
    HA1A (1) - +B (2)
    20°C (68°F)
    1.8 to 3.4 Ω
    HA1A (1) - A1A- (4)
    -
    10 kΩ or higher
    Bank 2 sensor 1:
    Tester Connection
    Condition
    Specified Condition
    HA2A (1) - +B (2)
    20°C (68°F)
    1.8 to 3.4 Ω
    HA2A (1) - A2A- (4)
    -
    10 kΩ or higher

  1. Reconnect the A/F sensor connector.



NG
REPLACE AIR FUEL RATIO SENSOR (Click here)
OK


2. INSPECT A/F FUSE

  1. A135031E01
    Remove the A/F fuse from the engine room junction block.

  1. Measure the A/F fuse resistance.

    Standard resistance:
    Below 1 Ω

  1. Reinstall the A/F fuse.



NG
REPLACE A/F FUSE
OK


3. INSPECT ENGINE ROOM JUNCTION BLOCK (A/F RELAY)

  1. A150648E05
    Remove the engine room junction block from the engine room R/B.

  1. Inspect the A/F relay.

    1. Measure the A/F relay resistance.

      Standard resistance:
      Tester Connection
      Specified Condition
      1G-1 - 1A-4
      10 kΩ or higher
      1G-1 - 1A-4
      Below 1 Ω
      (Apply battery voltage between terminals 1E-6 and 1E-11)

  1. Reinstall the engine room junction block.



NG
REPLACE ENGINE ROOM JUNCTION BLOCK
OK


4. CHECK HARNESS AND CONNECTOR (A/F SENSOR - ECM)

  1. A127715E46
    Disconnect the C15 and C35 A/F sensor connectors.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Specified Condition
    +B (C15-2) - Body ground
    9 to 14 V
    +B (C35-2) - Body ground
    9 to 14 V

  1. Turn the ignition switch off.

  1. Disconnect the C58 (RHD) or C55 (LHD) ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    RHD:
    Tester Connection
    Specified Condition
    HA1A (C15-1) - HA1A (C58-86)
    Below 1 Ω
    A1A+ (C15-3) - A1A+ (C58-93)
    Below 1 Ω
    A1A- (C15-4) - A1A- (C58-116)
    Below 1 Ω
    HA2A (C35-1) - HA2A (C58-109)
    Below 1 Ω
    A2A+ (C35-3) - A2A+ (C58-120)
    Below 1 Ω
    A2A- (C35-4) - A2A- (C58-119)
    Below 1 Ω
    LHD:
    Tester Connection
    Specified Condition
    HA1A (C15-1) - HA1A (C55-86)
    Below 1 Ω
    A1A+ (C15-3) - A1A+ (C55-93)
    Below 1 Ω
    A1A- (C15-4) - A1A- (C55-116)
    Below 1 Ω
    HA2A (C35-1) - HA2A (C55-109)
    Below 1 Ω
    A2A+ (C35-3) - A2A+ (C55-120)
    Below 1 Ω
    A2A- (C35-4) - A2A- (C55-119)
    Below 1 Ω


    Standard resistance (Check for short):
    RHD:
    Tester Connection
    Specified Condition
    HA1A (C15-1) or HA1A (C58-86) - Body ground
    10 kΩ or higher
    A1A+ (C15-3) or A1A+ (C58-93) - Body ground
    10 kΩ or higher
    A1A- (C15-4) or A1A- (C58-116) - Body ground
    10 kΩ or higher
    HA2A (C35-1) or HA2A (C58-109) - Body ground
    10 kΩ or higher
    A2A+ (C35-3) or A2A+ (C58-120) - Body ground
    10 kΩ or higher
    A2A- (C35-4) or A2A- (C58-119)- Body ground
    10 kΩ or higher
    LHD:
    Tester Connection
    Specified Condition
    HA1A (C15-1) or HA1A (C55-86) - Body ground
    10 kΩ or higher
    A1A+ (C15-3) or A1A+ (C55-93) - Body ground
    10 kΩ or higher
    A1A- (C15-4) or A1A- (C55-116) - Body ground
    10 kΩ or higher
    HA2A (C35-1) or HA2A (C55-109) - Body ground
    10 kΩ or higher
    A2A+ (C35-3) or A2A+ (C55-120) - Body ground
    10 kΩ or higher
    A2A- (C35-4) or A2A- (C55-119)- Body ground
    10 kΩ or higher

  1. Reconnect the ECM connector.

  1. Reconnect the A/F sensor connector.A133850E13



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)


← P2195 Oxygen (A/F) Sensor Signal Stuck Lean (Bank 1 Sensor 1) (+ P2196, P2197, P2198) (from Jun 2009)P2238 Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 1 Sensor 1) (+ 7 more codes) (Oct 2006 – May 2009) →