B2285 Steering Lock Position Signal Circuit Malfunction
Diagnostic trouble codes · Vehicles built from Jun 2009
Versions by build date: Oct 2006 – May 2009 from Jun 2009
DESCRIPTION
This DTC is output when serial communication signals and LIN communication signals in the circuit between the main body ECU and steering lock actuator (steering lock ECU) are inconsistent.- HINT:
- When the main body ECU is replaced with a new one and the negative (-) battery terminal is connected, the power source mode becomes the IG-ON mode. When the battery is removed and reinstalled, the power source mode that was selected when the battery was removed is restored.
- After the main body ECU or steering lock ECU is replaced, perform the registration procedures for the engine immobiliser system.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| B2285 |
Cable and LIN information between the main body ECU and the steering lock ECU are inconsistent |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. READ VALUE USING INTELLIGENT TESTER |
Connect the intelligent tester to the DLC3.
Check the DATA LIST for proper functioning of the steering lock function.
- HINT:
- When using the intelligent tester with the engine switch off, turn on and off any of the door courtesy light switches repeatedly at 1.5 second intervals or less until communication between the tester and vehicle starts.
Body: Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Str Unlock SW
Steering lock condition / ON or OFF
ON: Steering is unlocked (Engine switch on (ACC))
OFF: Steering is locked (Engine switch off)
-
- OK:
- ON (steering is unlocked) and OFF (steering is locked) appear on the screen.
|
|
||||
| OK | |
| 2. CHECK FOR DTCS |
Delete the DTCs (Click here).
Check for DTC B2285 (Steering lock position signal circuit malfunction), DTC B2287 (LIN communication master malfunction) and DTC B2785 (Communication malfunction between ECUs connected by LIN).
- Result:
Display (DTC output)
Proceed to
"DTC B2285" only
A
"DTC B2287" and/or "DTC B2785"
B
No DTC
C
- HINT:
- If DTC B2287 is output (Click here).
- If DTC B2785 is output (Click here).
- If DTC B2287 is output (Click here).
|
|
||||
|
|
||||
| A | ||
| ||
| 3. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - STEERING LOCK ECU) |
Disconnect the E7, IR and E51 ECU connectors.


Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
E7-18 (SLP) - E51-4 (SLP1)
Always
Below 1 Ω
IR-9 (LIN1) - E51-5 (LIN)
Always
Below 1 Ω
E7-18 (SLP) or E51-4 (SLP1) - Body ground
Always
10 kΩ or higher
IR-9 (LIN1) or E51-5 (LIN) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 4. CHECK MAIN BODY ECU OPERATION |
After replacing the main body ECU with a normally functioning ECU, check that the engine starts. Make sure the brake pedal is depressed and the shift position is P at this time.
Check that the engine switch mode can be changed by pushing the engine switch.
- HINT:
- Without depressing the brake pedal, push the engine switch repeatedly. Engine switch mode should turn from off to on (ACC) to on (IG) and back to off. With the brake pedal depressed, push the engine switch repeatedly. Engine switch mode should turn to ENGINE START from any status.
- OK:
- Engine can start normally.
|
|
||||
| OK | ||
| ||
