2006-2011 Camry Aurion · Service Manual RESTRAINTS

SRS Warning Light Remains ON

Circuit diagnosis · Vehicles built Jun 2006 – Sep 2006

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

The SRS warning light is located on the combination meter assembly.
When the SRS is normal, the SRS warning light comes on for approximately 6 seconds after the ignition switch is turned from LOCK to the ON position, and then goes off automatically.
If there is a malfunction in the SRS, the SRS warning light comes on to inform the driver of a problem.
When terminals TC and CG of the DLC3 are connected, the DTC is displayed by blinks of the SRS warning light.
The SRS is equipped with a voltage-increase circuit (DC-DC converter) in the center airbag sensor assembly in case the source voltage drops.
When the battery voltage drops, the voltage-increase circuit (DC-DC converter) functions to increase the voltage of the SRS to normal voltage.
A malfunction in this circuit is not recorded in the center airbag sensor assembly. The SRS warning light automatically goes off when the source voltage returns to normal.
The signal to illuminate the SRS warning light is transmitted from the center airbag sensor assembly to the combination meter assembly through the CAN communication system.

WIRING DIAGRAM

C142528E03

INSPECTION PROCEDURE


1. CHECK CAN COMMUNICATION SYSTEM
  1. Check if a CAN communication DTC is output (Click herefor LHD, Click here for RHD).

    Result:
    Condition
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
REPAIR CIRCUITS INDICATED BY OUTPUT DTCS
A


2. CHECK BATTERY
  1. Measure the voltage of the battery.

    Standard voltage:
    11 to 14 V



NG
CHECK AND REPLACE BATTERY OR CHARGING SYSTEM
OK


3. CHECK CONNECTORS
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor assembly and combination meter assembly.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


4. CHECK WIRE HARNESS (CENTER AIRBAG SENSOR ASSEMBLY - BODY GROUND)

  1. G027651E43
    Disconnect the connectors from the center airbag sensor assembly.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Operate all components of the electrical systems (defogger, wipers, headlights, heater blower, etc.).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    E30-21 (IG2) - Body ground
    Ignition switch ON
    10 to 14 V

  1. Turn the ignition switch to the LOCK position.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E30-25 (E1) - Body ground
    Always
    Below 1 Ω
    E30-26 (E2) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE WIRE HARNESS (CENTER AIRBAG SENSOR ASSEMBLY - BODY GROUND)
OK


5. CHECK WIRE HARNESS (COMBINATION METER ASSEMBLY - BODY GROUND)

  1. E134491E02
    Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the F1 connector from the combination meter assembly.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    F1-1 (B) - Body ground
    Ignition switch ON
    10 to 14 V
    F1-13 (IG+) - Body ground
    Ignition switch ON
    10 to 14 V

  1. Turn the ignition switch to the LOCK position.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    F1-12 (E2) - Body ground
    Always
    Below 1 Ω
    F1-24 (ES) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE WIRE HARNESS (COMBINATION METER ASSEMBLY - BODY GROUND)
OK


6. CHECK SRS WARNING LIGHT
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Connect the connector to the combination meter assembly.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Check the SRS warning light condition.

    OK:
    After the primary check period, the SRS warning light goes to the LOCK position for approximately 10 seconds, and then remains on.

    HINT:
    The primary check period shows approximately 6 seconds after the ignition switch is turned ON.



NG
GO TO METER / GAUGE SYSTEM (Click here)
OK

REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)


← B1905/74 Short in Front Passenger Side Pretensioner Squib Circuit (+ B1906/74, B1907/74, B1908/74) (from Jun 2009)SRS Warning Light Remains ON (Oct 2006 – May 2009) →