P0365 Camshaft Position Sensor "B" Circuit (Bank 1)
Diagnostic trouble codes · Vehicles built from Jun 2009
Also covers:
- P0367 Camshaft Position Sensor "B" Circuit Low Input (Bank 1)
- P0368 Camshaft Position Sensor "B" Circuit High Input (Bank 1)
- P0390 Camshaft Position Sensor "B" Circuit (Bank 2)
- P0392 Camshaft Position Sensor "B" Circuit Low Input (Bank 2)
- P0393 Camshaft Position Sensor "B" Circuit High Input (Bank 2)
Versions by build date: Oct 2006 – May 2009 from Jun 2009
DESCRIPTION
The exhaust camshaft's Variable Valve Timing (VVT) sensor consists of a magnet and MRE (Magnet Resistance Element).The exhaust camshaft has a sensor plate with 3 teeth on its outer circumference.
When the exhaust camshaft rotates, changes occur in the air gaps between the 3 teeth and MRE, which affects the magnet. As a result, the resistance of the MRE material fluctuates. The VVT sensor converts the exhaust camshaft rotation data to pulse signals, uses the pulse signals to determine the camshaft angle, and sends it to the ECM.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| P0365 P0390 |
|
|
| P0367 P0392 |
Output voltage of VVT sensor is 0.3 V or less for 5 seconds (1 trip detection logic) |
|
| P0368 P0393 |
Output voltage of VVT sensor is 4.7 V or more for 5 seconds (1 trip detection logic) |
|
-
Reference: Inspection using an oscilloscope

- HINT:
- The correct waveform is as shown.
- EV1+ and EV2+ stand for the VVT sensor signal, and NE+ stands for the CKP sensor signal.
Item
Content
Terminal
NE+ - NE-
EV1+ - EV1-
EV2+ - EV2-
Equipment Setting
5 V/DIV.
20 ms./DIV.
Condition
Cranking or idling
- The correct waveform is as shown.
WIRING DIAGRAM
Refer to DTC P0335 (Click here).INSPECTION PROCEDURE
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction (Click here).| 1. CHECK HARNESS AND CONNECTOR (SENSOR POWER SOURCE) |
Disconnect the C40 or C44 VVT sensor connector.

Measure the voltage according to the value(s) in the table below.
- Standard voltage:
Tester Connection
Specified Condition
VC2 (C40-3) - Body ground
4.5 to 5.0 V
VC2 (C44-3) - Body ground
4.5 to 5.0 V
Reconnect the VVT sensor connector.
|
|
||||
| OK | |
| 2. CHECK HARNESS AND CONNECTOR (VVT SENSOR - ECM) |
Disconnect the C40 or C44 VVT sensor connector.

Disconnect the C58 (RHD) or C55 (LHD) ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard resistance (Check for open):
- RHD:
Tester Connection
Specified Condition
EX+ (C40-1) - EV1+ (C58-68)
Below 1 Ω
EX- (C40-2) - EV1- (C58-91)
Below 1 Ω
EX+ (C44-1) - EV2+ (C58-66)
Below 1 Ω
EX- (C44-2) - EV2- (C58-89)
Below 1 Ω
- LHD:
Tester Connection
Specified Condition
EX+ (C40-1) - EV1+ (C55-68)
Below 1 Ω
EX- (C40-2) - EV1- (C55-91)
Below 1 Ω
EX+ (C44-1) - EV2+ (C55-66)
Below 1 Ω
EX- (C44-2) - EV2- (C55-89)
Below 1 Ω
- Standard resistance (Check for short):
- RHD:
Tester Connection
Specified Condition
EX+ (C40-1) or EV1+ (C58-68) - Body ground
10 kΩ or higher
EX- (C40-2) or EV1- (C58-91) - Body ground
10 kΩ or higher
EX+ (C44-1) or EV2+ (C58-66) - Body ground
10 kΩ or higher
EX- (C44-2) or EV2- (C58-89) - Body ground
10 kΩ or higher
- LHD:
Tester Connection
Specified Condition
EX+ (C40-1) or EV1+ (C55-68) - Body ground
10 kΩ or higher
EX- (C40-2) or EV1- (C55-91) - Body ground
10 kΩ or higher
EX+ (C44-1) or EV2+ (C55-66) - Body ground
10 kΩ or higher
EX- (C44-2) or EV2- (C55-89) - Body ground
10 kΩ or higher
Reconnect the VVT sensor connector.
Reconnect the ECM connector.
|
|
||||
| OK | |
| 3. CHECK VVT SENSOR FOR EXHAUST CAMSHAFT (SENSOR INSTALLATION) |
Check the VVT sensor installation.

- OK:
- Sensor is installed correctly.
|
|
||||
| OK | |
| 4. CHECK EXHAUST CAMSHAFT |
Check the teeth of the camshaft.
|
|
||||
| OK | |
| 5. REPLACE VVT SENSOR |
| NEXT | |
| 6. CHECK WHETHER DTC OUTPUT RECURS |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Turn the intelligent tester on.
Clear the DTCs (Click here).
Select the following menu items: Powertrain / Engine / DTC / Pending.
Read the DTCs.
- Result:
Display (DTC Output)
Proceed to
No output
A
P0365, P0352, P0353, P0354, P0355 or P0356
B
- HINT:
- If the engine does not start, replace the ECM.
|
|
||||
| A | ||
| ||
