ADJUSTMENT
Removal / installation · Vehicles built Jun 2006 – Sep 2006
Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009
| 1. INSPECT TIRES |
Check the tires for wear and proper inflation pressure.
- Cold tire inflation pressure:
for Australia: Tire size
Front kPa (kgf*cm2, psi)
Rear kPa (kgf*cm2, psi)
215/60R16 95V
4 passengers or less
210 (2.1, 31)*1, 230 (2.3, 33)*2
210 (2.1, 31)*1, 230 (2.3, 33)*2
5 passengers
240 (2.4, 35)*1, 300 (3.1, 44)*2
240 (2.4, 35)*1, 300 (3.1, 44)*2
215/55R17 93V
4 passengers or less
220 (2.2, 32)*1, 250 (2.5, 36)*2
220 (2.2, 32)*1, 250 (2.5, 36)*2
5 passengers
240 (2.4, 35)*1, 300 (3.1, 44)*2
240 (2.4, 35)*1, 300 (3.1, 44)*2
*2: For driving at over 140 km/h (87 mph).- Cold tire inflation pressure:
for GCC: Tire size
Front kPa (kgf*cm2, psi)
Rear kPa (kgf*cm2, psi)
215/60R16 95V
210 (2.1, 31)*1, 240 (2.4, 35)*2
210 (2.1, 31)*1, 240 (2.4, 35)*2
215/55R17 93V
220 (2.2, 32)*1, 240 (2.4, 35)*2
220 (2.2, 32)*1, 240 (2.4, 35)*2
*2: For driving at over 160 km/h (100 mph).
Using a dial indicator, check the runout of the tires.

- Tire runout:
- 1.4 mm (0.055 in.) or less
| 2. MEASURE VEHICLE HEIGHT |
Bounce the vehicle up and down at the corners to stabilize the suspension. Inspect the vehicle height.

- Vehicle height:
for Australia Model
Front A - B
Rear C - D
ACV40R-DEADKQ
129 mm (5.08 in.)
44 mm (1.73 in.)
ACV40R-DEAGKQ
ACV40R-DEANKQ
ACV40R-DEAVKQ
131 mm (5.16 in.)
49 mm (1.93 in.)
ACV40R-DEMDKQ
121 mm (4.76 in.)
45 mm (1.77 in.)
ACV40R-DEMVKQ
125 mm (4.92 in.)
51 mm (2.01 in.)
for Papua New Guinea and Fiji Model
Front A - B
Rear C - D
ACV40R-DEANKQ
119 mm (4.69 in.)
35 mm (1.38 in.)
for GCC Model
Front A - B
Rear C - D
ACV40L-DEADKV
129 mm (5.08 in.)
44 mm (1.73 in.)
ACV40L-DEANKV
ACV40L-DEASKV
131 mm (5.16 in.)
49 mm (1.93 in.)
ACV40L-DEMDKV
121 mm (4.76 in.)
45 mm (1.77 in.)
ACV40L-DEMNKV
ACV40L-DEMSKV
125 mm (4.92 in.)
51 mm (2.01 in.)
- Measuring points:
- A:
- Ground clearance of front wheel center
- B:
- Ground clearance of lower suspension arm No. 2 bushing set bolt center
- C:
- Ground clearance of rear wheel center
- D:
- Ground clearance of strut rod set bolt center
- NOTICE:
- Before inspecting the wheel alignment, adjust the vehicle height to the specified value.
- Be sure to perform measurement on a level surface.
- If it is necessary to go under the vehicle for measurement, confirm that the parking brake is applied and the vehicle is secured with chocks.
- Before inspecting the wheel alignment, adjust the vehicle height to the specified value.
| 3. INSPECT TOE-IN |
Bounce the vehicle up and down at the corners to stabilize the suspension.
Release the parking brake and move the shift lever to the neutral position.
Push the vehicle straight ahead approximately 5 m (16.4 ft). (*1)
Put tread center marks on the rearmost points of the front wheels and measure the distance between the marks (dimension B).

Slowly push the vehicle straight ahead to cause the front wheels to rotate 180° using the front tire valve as a reference point.
- HINT:
- Do not allow the wheels to rotate more than 180°. If the wheels rotate more than 180°, perform the procedure from *1 again.
Measure the distance between the tread center marks on the front side of the wheels.

- Toe-in:
Toe-in
-
A - B:
0 +- 2 mm (0 +- 0.08 in.)
- HINT:
- If toe-in is not within the specified range, adjust it at the rack ends.
| 4. ADJUST TOE-IN |
Measure the thread lengths of the right and left rack ends.

- Standard:
- Difference in thread length between the right and left rack ends is 1.5 mm (0.06 in.) or less.
Remove the rack boot set clips.
Loosen the tie rod end lock nuts.
Adjust the rack ends if the difference in thread length between the right and left rack ends is not within the specified range.
Extend the shorter rack end if the measured toe-in deviates toward the outside.
Shorten the longer rack end if the measured toe-in deviates toward the inside.
Turn the right and left rack ends by equal amounts to adjust the toe-in.
- HINT:
- Try to adjust the toe-in to the center of the specified range.
Make sure that the lengths of the right and left rack ends are the same.
Tighten the tie rod end lock nuts.
- Torque:
- 74 N*m{ 755 kgf*cm , 55 ft.*lbf }
- NOTICE:
- Temporarily tighten the lock nut while holding the hexagonal part of the steering rack end so that the lock nut and the steering rack end do not turn together. Hold the flats on the tie rod end and tighten the lock nut.
Place the boots on the seats and install the clips.
- HINT:
- Make sure that the boots are not twisted.
| 5. INSPECT WHEEL ANGLE |
Put tread center marks on the rearmost points of the turning radius gauge.
Turn the steering wheel fully to the left and right and measure the turning angle.

- Wheel turning angle:
for Australia Inside wheel
Outside wheel: reference
38°22' +-2° (38.37° +-2°)
33°33' (33.55°)
for Papua New Guinea and Fiji Inside wheel
Outside wheel: reference
38°42' +-2° (38.70° +-2°)
33°46' (33.77°)
for GCC Inside wheel
Outside wheel: reference
38°22' +-2° (38.37° +-2°)
33°33' (33.55°)
| 6. INSPECT CAMBER, CASTER AND STEERING AXIS INCLINATION |
Put the front wheel on the center of the alignment tester.

Remove the center ornament.
Set the camber-caster-king pin gauge and attachment at the center of the axle hub or drive shaft.
Inspect the camber, caster, and steering axis inclination.
- Camber:
for Australia Model
Camber
Right-left difference
ACV40R-DEADKQ
-0°45' +-45' (-0.75° +-0.75°)
45' (0.75°) or less
ACV40R-DEAGKQ
ACV40R-DEANKQ
ACV40R-DEAVKQ
ACV40R-DEMDKQ
-0°40' +-45' (-0.67° +-0.75°)
ACV40R-DEMVKQ
for Papua New Guinea and Fiji Model
Camber
Right-left difference
ACV40R-DEANKQ
-0°35' +-45' (-0.58° +-0.75°)
45' (0.75°) or less
for GCC Model
Camber
Right-left difference
ACV40L-DEADKV
-0°45' +-45' (-0.75° +-0.75°)
45' (0.75°) or less
ACV40L-DEANKV
ACV40L-DEASKV
ACV40L-DEMDKV
-0°40' +-45' (-0.67° +-0.75°)
ACV40L-DEMNKV
ACV40L-DEMSKV
- Caster:
for Australia Model
Caster
Right-left difference
ACV40R-DEADKQ
2°45' +-45' (2.75° +-0.75°)
45' (0.75°) or less
ACV40R-DEAGKQ
ACV40R-DEANKQ
ACV40R-DEAVKQ
2°50' +-45' (2.83° +-0.75°)
ACV40R-DEMDKQ
2°55' +-45' (2.92° +-0.75°)
ACV40R-DEMVKQ
for Papua New Guinea and Fiji Model
Caster
Right-left difference
ACV40R-DEANKQ
2°40' +-45' (2.67° +-0.75°)
45' (0.75°) or less
for GCC Model
Caster
Right-left difference
ACV40L-DEADKV
2°45' +-45' (2.75° +-0.75°)
45' (0.75°) or less
ACV40L-DEANKV
ACV40L-DEASKV
2°50' +-45' (2.83° +-0.75°)
ACV40L-DEMDKV
2°55' +-45' (2.92° +-0.75°)
ACV40L-DEMNKV
ACV40L-DEMSKV
- Steering axis inclination:
for Australia Model
Steering axis inclination
Right-left difference
ACV40R-DEADKQ
12°20' +-45' (12.33° +-0.75°)
45' (0.75°) or less
ACV40R-DEAGKQ
ACV40R-DEANKQ
ACV40R-DEAVKQ
ACV40R-DEMDKQ
12°10' +-45' (12.17° +-0.75°)
ACV40R-DEMVKQ
12°15' +-45' (12.25° +-0.75°)
for Papua New Guinea and Fiji Model
Steering axis inclination
Right-left difference
ACV40R-DEANKQ
12°05' +-45' (12.08° +-0.75°)
45' (0.75°) or less
for GCC Model
Steering axis inclination
Right-left difference
ACV40L-DEADKV
12°20' +-45' (12.33° +-0.75°)
45' (0.75°) or less
ACV40L-DEANKV
ACV40L-DEASKV
ACV40L-DEMDKV
12°10' +-45' (12.17° +-0.75°)
ACV40L-DEMNKV
ACV40L-DEMSKV
12°15' +-45' (12.25° +-0.75°)
- NOTICE:
- Perform the inspection while the vehicle is unloaded.
- The maximum tolerance of the right and left difference for the camber and caster is 45' (0.75°) or less.
- Perform the inspection while the vehicle is unloaded.
Remove the camber-caster-king pin gauge and attachment.
Install the center ornament.
If the caster and steering axis inclination are not within the specified range after the camber has been correctly adjusted, recheck the suspension parts for damage and/or wear.
| 7. ADJUST CAMBER |
- NOTICE:
- Inspect toe-in after the camber has been adjusted.
Remove the front wheel.
Remove the 2 nuts on the lower side of the front shock absorber.

- NOTICE:
- Keep the bolts inserted.
Clean the installation surfaces of the front shock absorber and the steering knuckle.
Temporarily install the 2 nuts (Step A).
Fully push or pull the front axle hub in the direction of the required adjustment (Step B).

Tighten the nuts.
- Torque:
- 210 N*m{ 2,141 kgf*cm , 155 ft.*lbf }
- NOTICE:
- Keep the bolts from rotating when tightening the nuts.
Install the front wheel.
- Torque:
- 103 N*m{ 1,050 kgf*cm , 76 ft.*lbf }
Check the camber.





If the measured value is not within the specification, calculate the required adjustment amount using the formula below.
Camber adjustment amount = center of the specified range center - measured value
Check the combination of installed bolts. Select appropriate bolts from the table below to adjust the camber to the specified values.- HINT:
- Try to adjust the camber to the center of the specified values.
The body and suspension may be damaged if the camber is not correctly adjusted according to the above table.Move the axle toward (+) in step (B)
Move the axle toward (-) in step (B)
Refer to table (1) (Move the axle toward the positive side)
Refer to table (2) (Move the axle toward the negative side)
- NOTICE:
- Replace the nut with a new one when replacing the bolt.
Repeat the steps mentioned above. In step (A), replace 1 or 2 selected bolts.
- HINT:
- Replace one bolt at a time when replacing 2 bolts.
