2006-2011 Camry Aurion · Service Manual SUSPENSION & AXLE

ADJUSTMENT

Removal / installation · Vehicles built Oct 2006 – May 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009


1. INSPECT TIRES
  1. Check the tires for wear and proper inflation pressure.

    Cold tire inflation pressure:
    for Australia: 
    Tire size
    Front kPa (kgf*cm2, psi)
    Rear kPa (kgf*cm2, psi)
    215/60R16 95V
    4 passengers or less
    210 (2.1, 31)*1, 230 (2.3, 33)*2
    210 (2.1, 31)*1, 230 (2.3, 33)*2
    5 passengers
    240 (2.4, 35)*1, 300 (3.1, 44)*2
    240 (2.4, 35)*1, 300 (3.1, 44)*2
    215/55R17 93V
    4 passengers or less
    220 (2.2, 32)*1, 250 (2.5, 36)*2
    220 (2.2, 32)*1, 250 (2.5, 36)*2
    5 passengers
    240 (2.4, 35)*1, 300 (3.1, 44)*2
    240 (2.4, 35)*1, 300 (3.1, 44)*2

    *1: For driving at under 140 km/h (87 mph).
    *2: For driving at over 140 km/h (87 mph).

    Cold tire inflation pressure:
    for GCC: 
    Tire size
    Front kPa (kgf*cm2, psi)
    Rear kPa (kgf*cm2, psi)
    215/60R16 95V
    210 (2.1, 31)*1, 240 (2.4, 35)*2
    210 (2.1, 31)*1, 240 (2.4, 35)*2
    215/55R17 93V
    220 (2.2, 32)*1, 240 (2.4, 35)*2
    220 (2.2, 32)*1, 240 (2.4, 35)*2

    *1: For driving at under 160 km/h (100 mph).
    *2: For driving at over 160 km/h (100 mph).

  1. C137874
    Using a dial indicator, check the runout of the tires.

    Tire runout:
    1.4 mm (0.055 in.) or less


2. MEASURE VEHICLE HEIGHT

  1. C132408E01
    Bounce the vehicle up and down at the corners to stabilize the suspension. Inspect the vehicle height.

    Vehicle height:
    for Australia 
    Model
    Front A - B
    Rear C - D
    ACV40R-DEADKQ
    129 mm (5.08 in.)
    44 mm (1.73 in.)
    ACV40R-DEAGKQ
    ACV40R-DEANKQ
    ACV40R-DEAVKQ
    131 mm (5.16 in.)
    49 mm (1.93 in.)
    ACV40R-DEMDKQ
    121 mm (4.76 in.)
    45 mm (1.77 in.)
    ACV40R-DEMVKQ
    125 mm (4.92 in.)
    51 mm (2.01 in.)
    GSV40R-JETDKQ
    128 mm (5.04 in.)
    47 mm (1.85 in.)
    GSV40R-JETGKQ
    GSV40R-JETNKQ
    GSV40R-JETSKQ
    130 mm (5.12 in.)
    51 mm (2.01 in.)
    GSV40R-JETVKQ
    for Papua New Guinea and Fiji 
    Model
    Front A - B
    Rear C - D
    ACV40R-DEANKQ
    119 mm (4.69 in.)
    35 mm (1.38 in.)
    GSV40R-JETNKQ
    for GCC 
    Model
    Front A - B
    Rear C - D
    ACV40L-DEADKV
    129 mm (5.08 in.)
    44 mm (1.73 in.)
    ACV40L-DEANKV
    ACV40L-DEASKV
    131 mm (5.16 in.)
    49 mm (1.93 in.)
    ACV40L-DEMDKV
    121 mm (4.76 in.)
    45 mm (1.77 in.)
    ACV40L-DEMNKV
    ACV40L-DEMSKV
    125 mm (4.92 in.)
    51 mm (2.01 in.)
    GSV40L-JETDKV
    128 mm (5.04 in.)
    47 mm (1.85 in.)
    GSV40L-JETGKV

    Measuring points:
    A:
    Ground clearance of front wheel center
    B:
    Ground clearance of lower suspension arm No. 2 bushing set bolt center
    C:
    Ground clearance of rear wheel center
    D:
    Ground clearance of strut rod set bolt center

    NOTICE:
    1. Before inspecting the wheel alignment, adjust the vehicle height to the specified value.
    2. Be sure to perform measurement on a level surface.
    3. If it is necessary to go under the vehicle for measurement, confirm that the parking brake is applied and the vehicle is secured with chocks.


3. INSPECT TOE-IN
  1. Bounce the vehicle up and down at the corners to stabilize the suspension.

  1. Release the parking brake and move the shift lever to the neutral position.

  1. Push the vehicle straight ahead approximately 5 m (16.4 ft.). (*1)

  1. C125225E02
    Put tread center marks on the rearmost points of the front wheels and measure the distance between the marks (dimension B).

  1. Slowly push the vehicle straight ahead to cause the front wheels to rotate 180° using the front tire valve as a reference point.

    HINT:
    Do not allow the wheels to rotate more than 180°. If the wheels rotate more than 180°, perform the procedure from *1 again.

  1. C125226E04
    Measure the distance between the tread center marks on the front side of the wheels.

    Toe-in:
    Toe-in
    -
    A - B:
    0 +- 2 mm (0 +- 0.08 in.)

    HINT:
    If toe-in is not within the specified range, adjust it at the rack ends.


4. ADJUST TOE-IN

  1. C148946
    Measure the thread lengths of the right and left rack ends.

    Standard:
    Difference in thread length between the right and left rack ends is 1.5 mm (0.06 in.) or less.

  1. Remove the rack boot set clips.

  1. Loosen the tie rod end lock nuts.

  1. Adjust the rack ends if the difference in thread length between the right and left rack ends is not within the specified range.

    1. Extend the shorter rack end if the measured toe-in deviates toward the outside.

    2. Shorten the longer rack end if the measured toe-in deviates toward the inside.

  1. Turn the right and left rack ends by equal amounts to adjust the toe-in.

    HINT:
    Try to adjust the toe-in to the center of the specified range.

  1. Make sure that the lengths of the right and left rack ends are the same.

  1. Tighten the tie rod end lock nuts.

    Torque:
    74 N*m{ 755 kgf*cm , 55 ft.*lbf }

    NOTICE:
    Temporarily tighten the lock nut while holding the hexagonal part of the steering rack end so that the lock nut and the steering rack end do not turn together. Hold the flats on the tie rod end and tighten the lock nut.

  1. Place the boots on the seats and install the clips.

    HINT:
    Make sure that the boots are not twisted.


5. INSPECT WHEEL ANGLE
  1. Put tread center marks on the rearmost points of the turning radius gauge.

  1. C132439E01
    Turn the steering wheel fully to the left and right and measure the turning angle.

    Wheel turning angle:
    for Australia 
    Inside wheel
    Outside wheel: reference
    38°22' +-2° (38.37° +-2°)
    33°33' (33.55°)
    for Papua New Guinea and Fiji 
    Inside wheel
    Outside wheel: reference
    38°42' +-2° (38.70° +-2°)
    33°46' (33.77°)
    for GCC 
    Inside wheel
    Outside wheel: reference
    38°22' +-2° (38.37° +-2°)
    33°33' (33.55°)

    If the right and left inside wheel angles differ from the specified value, check the right and left rack end lengths.


6. INSPECT CAMBER, CASTER AND STEERING AXIS INCLINATION

  1. C132440E01
    Put the front wheel on the center of the alignment tester.

  1. Remove the center ornament.

  1. Set the camber-caster-king pin gauge and attachment at the center of the axle hub or drive shaft.

  1. Inspect the camber, caster, and steering axis inclination.

    Camber:
    for Australia 
    Model
    Camber
    Right-left difference
    ACV40R-DEADKQ
    -0°45' +-45' (-0.75° +-0.75°)
    45' (0.75°) or less
    ACV40R-DEAGKQ
    ACV40R-DEANKQ
    ACV40R-DEAVKQ
    ACV40R-DEMDKQ
    -0°40' +-45' (-0.67° +-0.75°)
    ACV40R-DEMVKQ
    GSV40R-JETDKQ
    -0°40' +-45' (-0.67° +-0.75°)
    GSV40R-JETGKQ
    GSV40R-JETNKQ
    GSV40R-JETSKQ
    -0°45' +-45' (-0.75° +-0.75°)
    GSV40R-JETVKQ
    for Papua New Guinea and Fiji 
    Model
    Camber
    Right-left difference
    ACV40R-DEANKQ
    -0°35' +-45' (-0.58° +-0.75°)
    45' (0.75°) or less
    GSV40R-JETNKQ
    for GCC 
    Model
    Camber
    Right-left difference
    ACV40L-DEADKV
    -0°45' +-45' (-0.75° +-0.75°)
    45' (0.75°) or less
    ACV40L-DEANKV
    ACV40L-DEASKV
    ACV40L-DEMDKV
    -0°40' +-45' (-0.67° +-0.75°)
    ACV40L-DEMNKV
    ACV40L-DEMSKV
    GSV40L-JETDKV
    -0°40' +-45' (-0.67° +-0.75°)
    GSV40L-JETGKV


    Caster:
    for Australia 
    Model
    Caster
    Right-left difference
    ACV40R-DEADKQ
    2°45' +-45' (2.75° +-0.75°)
    45' (0.75°) or less
    ACV40R-DEAGKQ
    ACV40R-DEANKQ
    ACV40R-DEAVKQ
    2°50' +-45' (2.83° +-0.75°)
    ACV40R-DEMDKQ
    2°55' +-45' (2.92° +-0.75°)
    ACV40R-DEMVKQ
    GSV40R-JETDKQ
    2°50' +-45' (2.83° +-0.75°)
    GSV40R-JETGKQ
    GSV40R-JETNKQ
    GSV40R-JETSKQ
    2°45' +-45' (2.75° +-0.75°)
    GSV40R-JETVKQ
    for Papua New Guinea and Fiji 
    Model
    Caster
    Right-left difference
    ACV40R-DEANKQ
    2°40' +-45' (2.67° +-0.75°)
    45' (0.75°) or less
    GSV40R-JETNKQ
    for GCC 
    Model
    Caster
    Right-left difference
    ACV40L-DEADKV
    2°45' +-45' (2.75° +-0.75°)
    45' (0.75°) or less
    ACV40L-DEANKV
    ACV40L-DEASKV
    2°50' +-45' (2.83° +-0.75°)
    ACV40L-DEMDKV
    2°55' +-45' (2.92° +-0.75°)
    ACV40L-DEMNKV
    ACV40L-DEMSKV
    GSV40L-JETDKV
    2°50' +-45' (2.83° +-0.75°)
    GSV40L-JETGKV


    Steering axis inclination:
    for Australia 
    Model
    Steering axis inclination
    Right-left difference
    ACV40R-DEADKQ
    12°20' +-45' (12.33° +-0.75°)
    45' (0.75°) or less
    ACV40R-DEAGKQ
    ACV40R-DEANKQ
    ACV40R-DEAVKQ
    ACV40R-DEMDKQ
    12°10' +-45' (12.17° +-0.75°)
    ACV40R-DEMVKQ
    12°15' +-45' (12.25° +-0.75°)
    GSV40R-JETDKQ
    12°20' +-45' (12.33° +-0.75°)
    GSV40R-JETGKQ
    GSV40R-JETNKQ
    GSV40R-JETSKQ
    GSV40R-JETVKQ
    for Papua New Guinea and Fiji 
    Model
    Steering axis inclination
    Right-left difference
    ACV40R-DEANKQ
    12°05' +-45' (12.08° +-0.75°)
    45' (0.75°) or less
    GSV40R-JETNKQ
    for GCC 
    Model
    Steering axis inclination
    Right-left difference
    ACV40L-DEADKV
    12°20' +-45' (12.33° +-0.75°)
    45' (0.75°) or less
    ACV40L-DEANKV
    ACV40L-DEASKV
    ACV40L-DEMDKV
    12°10' +-45' (12.17° +-0.75°)
    ACV40L-DEMNKV
    ACV40L-DEMSKV
    12°15' +-45' (12.25° +-0.75°)
    GSV40L-JETDKV
    12°20' +-45' (12.33° +-0.75°)
    GSV40L-JETGKV

    NOTICE:
    1. Perform the inspection while the vehicle is unloaded.
    2. The maximum tolerance of the right and left difference for the camber and caster is 45' (0.75°) or less.

  1. Remove the camber-caster-king pin gauge and attachment.

  1. Install the center ornament.

  1. If the caster and steering axis inclination are not within the specified range after the camber has been correctly adjusted, recheck the suspension parts for damage and/or wear.


7. ADJUST CAMBER

NOTICE:
Inspect toe-in after the camber has been adjusted.

  1. Remove the front wheel.

  1. C132409
    Remove the 2 nuts on the lower side of the front shock absorber.

    NOTICE:
    Keep the bolts inserted.

  1. Clean the installation surfaces of the front shock absorber and the steering knuckle.

  1. Temporarily install the 2 nuts (Step A).

  1. C111319E01
    Fully push or pull the front axle hub in the direction of the required adjustment (Step B).

  1. Tighten the nuts.

    Torque:
    210 N*m{ 2,141 kgf*cm , 155 ft.*lbf }

    NOTICE:
    Keep the bolts from rotating when tightening the nuts.

  1. Install the front wheel.

    Torque:
    103 N*m{ 1,050 kgf*cm , 76 ft.*lbf }

  1. C140710E01
    C138332E01
    C138332E02
    Check the camber.
    If the measured value is not within the specification, calculate the required adjustment amount using the formula below.
    Camber adjustment amount = center of the specified range center - measured value
    Check the combination of installed bolts. Select appropriate bolts from the table below to adjust the camber to the specified values.

    HINT:
    Try to adjust the camber to the center of the specified values.

    Move the axle toward (+) in step (B)
    Move the axle toward (-) in step (B)
    Refer to table (1) (Move the axle toward the positive side)
    Refer to table (2) (Move the axle toward the negative side)
    The body and suspension may be damaged if the camber is not correctly adjusted according to the above table.

    NOTICE:
    Replace the nut with a new one when replacing the bolt.

  1. Repeat the steps mentioned above. In step (A), replace 1 or 2 selected bolts.

    HINT:
    Replace one bolt at a time when replacing 2 bolts.

← ADJUSTMENT (Jun 2006 – Sep 2006)ADJUSTMENT (from Jun 2009) →