2006-2011 Camry Aurion · Service Manual SUSPENSION & AXLE

INSTALLATION

Removal / installation · Vehicles built from Jun 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009


1. INSTALL REAR SHOCK ABSORBER WITH COIL SPRING

  1. C144663
    Install the rear shock absorber with coil spring to the rear axle carrier assembly and insert the 2 bolts from the rear of the vehicle.

  1. C132459E02
    Slowly jack up the vehicle using a wooden block and install the rear shock absorber with coil spring (upper side) to the vehicle.

  1. C132465
    Install the 3 nuts to the upper side of the rear shock absorber with coil spring.

    Torque:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }

  1. C132464
    Install the 2 nuts to the lower side of the rear shock absorber with coil spring.

    Torque:
    180 N*m{ 1,840 kgf*cm , 133 ft.*lbf }

    NOTICE:
    When installing the nuts, keep the bolts from rotating.

  1. C132463
    Fully tighten the lock nut.

    Torque:
    55 N*m{ 561 kgf*cm , 41 ft.*lbf }


2. CONNECT REAR SPEED SENSOR

  1. C132461E01
    Install the rear brake flexible hose and rear speed sensor wire harness with the 2 bolts to the rear shock absorber with coil spring.

    Torque:
    Bolt A:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }
    Bolt B:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }


3. INSTALL REAR STABILIZER LINK ASSEMBLY

  1. C144666E01
    Install the rear stabilizer link assembly to the rear shock absorber with the nut.

    Torque:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }

    HINT:
    If the ball joint turns together with the nut, use a hexagon wrench (5 mm) to hold the stud.


4. INSTALL NO. 1 REAR SUSPENSION SUPPORT COVER

  1. C132501
    Engage the 4 claws and install the No. 1 rear suspension support cover.


5. INSTALL REAR WHEEL

Torque:
103 N*m{ 1,050 kgf*cm , 76 ft.*lbf }


6. INSTALL REAR SEATBACK ASSEMBLY (for Fixed Type)

  1. B136577
    Place the seatback in the cabin.

    NOTICE:
    Be careful not to damage the vehicle body.

  1. Install the rear seatback assembly with the 4 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

  1. B136576
    Pass the 3 seat belts through and close the cap of the 2 rear seat shoulder belt guides.

  1. Install the floor anchor part with the bolt.


7. INSTALL REAR SEAT CUSHION ASSEMBLY (for Fixed Type)

  1. B140589E01
    Attach the 2 front hooks of the seat cushion to the vehicle body.

  1. Confirm that the seat cushion is firmly installed.

    NOTICE:
    When installing the seat cushion, make sure the seat belt buckle is not under the seat cushion.


8. INSTALL REAR CENTER SEAT HEADREST ASSEMBLY (for Fixed Type)

9. INSTALL REAR SEAT HEADREST ASSEMBLY (for Fixed Type)

10. INSTALL REAR SIDE SEATBACK ASSEMBLY RH (for Fold Down Seat Type)

11. INSTALL REAR SIDE SEATBACK ASSEMBLY LH (for Fold Down Seat Type)

  1. B136561
    Install the rear side seatback assembly with the bolt.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }


12. INSTALL SEPARATE TYPE REAR SEATBACK ASSEMBLY RH (for Fold Down Seat Type)

  1. B134700
    Install the separate type rear seatback assembly with the 2 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }


13. INSTALL SEPARATE TYPE REAR SEATBACK ASSEMBLY LH (for Fold Down Seat Type)

  1. B136539
    Install the separate type rear seatback assembly with the 2 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }


14. INSTALL REAR SEAT CUSHION ASSEMBLY (for Fold Down Seat Type)

  1. B140584E01
    Attach the front hooks of the bench type rear seat cushion assembly to the vehicle body.

  1. Confirm that the seat cushion is firmly installed.

    NOTICE:
    When installing the bench type rear seat cushion assembly, make sure that the seat belt buckle is not under the bench type rear seat cushion assembly.


15. INSTALL REAR CENTER SEAT HEADREST ASSEMBLY (w/ Center Armrest)

16. INSTALL REAR SEAT HEADREST ASSEMBLY (for Fold Down Seat Type)

17. CHECK ABS SPEED SENSOR SIGNAL

HINT:
  1. ABS: Click here.
  2. VSC: Click here.


18. INSPECT AND ADJUST REAR WHEEL ALIGNMENT
(Click here)
← INSTALLATION (Oct 2006 – May 2009)DISPOSAL (from Jun 2006) →