INSTALLATION
Removal / installation · Vehicles built Oct 2006 – May 2009
Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009
| 1.
INSTALL REAR SHOCK ABSORBER WITH COIL SPRING |
 |
- Install the rear shock absorber with coil spring to the rear axle carrier assembly and insert the 2 bolts from the rear of the vehicle.
- Slowly jack up the vehicle using a wooden block and install the rear shock absorber with coil spring (upper side) to the vehicle.
- Install the 3 nuts to the upper side of the rear shock absorber with coil spring.
-
Torque:
- 39 N*m{
398 kgf*cm
, 29 ft.*lbf
}
- Install the 2 nuts to the lower side of the rear shock absorber with coil spring.
-
Torque:
- 180 N*m{
1,840 kgf*cm
, 133 ft.*lbf
}
- NOTICE:
- When installing the nuts, keep the bolts from rotating.
- Fully tighten the lock nut.
-
Torque:
- 55 N*m{
561 kgf*cm
, 41 ft.*lbf
}
| 2.
CONNECT REAR SPEED SENSOR |
 |
- Install the rear brake flexible hose and rear speed sensor wire harness with the 2 bolts to the rear shock absorber with coil spring.
-
Torque:
- Bolt A:
- 5.0 N*m{
51 kgf*cm
, 44 in.*lbf
}
- Bolt B:
- 19 N*m{
194 kgf*cm
, 14 ft.*lbf
}
| 3.
INSTALL REAR STABILIZER LINK ASSEMBLY |
 |
- Install the rear stabilizer link assembly to the rear shock absorber with the nut.
-
Torque:
- 39 N*m{
398 kgf*cm
, 29 ft.*lbf
}
- HINT:
- If the ball joint turns together with the nut, use a hexagon wrench (5 mm) to hold the stud.
| 4.
INSTALL NO. 1 REAR SUSPENSION SUPPORT COVER |
 |
- Engage the 4 claws and install the No. 1 rear suspension support cover.
| 5.
INSTALL REAR WHEEL |
 |
-
Torque:
- 103 N*m{
1,050 kgf*cm
, 76 ft.*lbf
}
| 6.
INSTALL REAR SEATBACK ASSEMBLY (for Fixed Type)
|
 |
- Place the seatback in the cabin.
- NOTICE:
- Be careful not to damage the vehicle body.
Install the rear seatback assembly with the 4 bolts.
-
Torque:
- 18 N*m{
184 kgf*cm
, 13 ft.*lbf
}
- Pass the 3 seat belts through and close the cap of the 2 rear seat shoulder belt guides.
Install the floor anchor part with the bolt.
| 7.
INSTALL REAR SEAT CUSHION ASSEMBLY (for Fixed Type)
|
 |
- Attach the 2 front hooks of the seat cushion to the vehicle body.
Confirm that the seat cushion is firmly installed.
- NOTICE:
- When installing the seat cushion, make sure the seat belt buckle is not under the seat cushion.
| 8.
INSTALL REAR CENTER SEAT HEADREST ASSEMBLY (for Fixed Type) |
|
| 9.
INSTALL REAR SEAT HEADREST ASSEMBLY (for Fixed Type) |
|
| 10.
INSTALL REAR SIDE SEATBACK ASSEMBLY RH (for Fold Down Seat Type) |
|
| 11.
INSTALL REAR SIDE SEATBACK ASSEMBLY LH (for Fold Down Seat Type)
|
 |
- Install the rear side seatback assembly with the bolt.
-
Torque:
- 18 N*m{
184 kgf*cm
, 13 ft.*lbf
}
| 12.
INSTALL SEPARATE TYPE REAR SEATBACK ASSEMBLY RH (for Fold Down Seat Type)
|
 |
- Install the separate type rear seatback assembly with the 2 bolts.
-
Torque:
- 18 N*m{
184 kgf*cm
, 13 ft.*lbf
}
| 13.
INSTALL SEPARATE TYPE REAR SEATBACK ASSEMBLY LH (for Fold Down Seat Type)
|
 |
- Install the separate type rear seatback assembly with the 2 bolts.
-
Torque:
- 18 N*m{
184 kgf*cm
, 13 ft.*lbf
}
| 14.
INSTALL REAR SEAT CUSHION ASSEMBLY (for Fold Down Seat Type)
|
 |
- Attach the front hooks of the bench type rear seat cushion assembly to the vehicle body.
Confirm that the seat cushion is firmly installed.
- NOTICE:
- When installing the bench type rear seat cushion assembly, make sure that the seat belt buckle is not under the bench type rear seat cushion assembly.
| 15.
INSTALL REAR CENTER SEAT HEADREST ASSEMBLY (w/ Center Armrest) |
|
| 16.
INSTALL REAR SEAT HEADREST ASSEMBLY (for Fold Down Seat Type) |
|
| 17.
CHECK ABS SPEED SENSOR SIGNAL |
 |
- HINT:
- ABS: Click here.
- VSC: Click here.
| 18.
INSPECT AND ADJUST REAR WHEEL ALIGNMENT |
 |
(Click here)