REMOVAL
Removal / installation · Vehicles built from Oct 2006
Versions by build date: Jun 2006 – Sep 2006 from Oct 2006
- NOTICE:
- If an old gasket still remains on the pipe, remove it. Also, if any bolts or nuts are rusted, replace them.
| 2.
REMOVE CENTER EXHAUST PIPE ASSEMBLY (for 2AZ-FE)
|
 |
Remove the 2 bolts, 2 nuts and center exhaust pipe assembly.


Remove the gasket from the front exhaust pipe.
| 3.
REMOVE TAIL EXHAUST PIPE ASSEMBLY (for 2GR-FE)
|
 |
Remove the 4 nuts and 2 exhaust tail pipes.


Remove the 2 gaskets from the exhaust tail pipes.
| 4.
REMOVE CENTER EXHAUST PIPE ASSEMBLY (for 2GR-FE)
|
 |
Remove the 2 bolts, 2 nuts and exhaust center pipe assembly.


Remove the gasket from the exhaust front pipe assembly.
| 5.
SEPARATE REAR STABILIZER LINK ASSEMBLY LH
|
 |
- Remove the nut and separate the rear stabilizer link assembly LH (lower side) from the rear stabilizer bar.
- HINT:
- If the ball joint turns together with the nut, use a hexagon wrench (5 mm) to hold the stud.
| 6.
SEPARATE REAR STABILIZER LINK ASSEMBLY RH
|
 |
- HINT:
- Perform the same procedures as for the LH side.
| 7.
REMOVE NO. 2 REAR STABILIZER BAR BRACKET
|
 |
- Remove the 2 bolts and No. 2 rear stabilizer bar bracket.
| 8.
REMOVE NO. 1 REAR STABILIZER BAR BRACKET
|
 |
- Remove the 2 bolts and No. 1 rear stabilizer bar bracket.
| 9.
REMOVE REAR STABILIZER BAR
|
 |
Remove the rear stabilizer bar with the stabilizer bushing.
| 10.
DISCONNECT REAR HEIGHT CONTROL SENSOR CONNECTOR (w/ HID Headlight System) |
 |
- Disconnect the rear height control sensor connector.
| 11.
SEPARATE REAR STRUT ROD LH |
 |
- Support the rear axle carrier with a jack.
Remove the bolt and nut, and separate the rear strut rod LH (rear side) from the rear axle carrier.
- NOTICE:
- When removing the bolt, keep the nut from rotating.
| 12.
SEPARATE REAR STRUT ROD RH |
 |
- HINT:
- Perform the same procedures as for the LH side.
| 13.
SEPARATE REAR NO. 2 SUSPENSION ARM LH |
 |
- Remove the bolt and nut, and separate the rear No. 2 suspension arm (outer side) from the rear axle carrier.
- NOTICE:
- When removing the bolt, keep the nut from rotating.
| 14.
SEPARATE REAR NO. 2 SUSPENSION ARM RH |
 |
- HINT:
- Perform the same procedures as for the LH side.
| 15.
SEPARATE REAR NO. 1 SUSPENSION ARM LH |
 |
- Remove the bolt and nut, and separate the rear No. 1 suspension arm (outer side) from the rear axle carrier.
- NOTICE:
- When removing the bolt, keep the nut from rotating.
| 16.
SEPARATE REAR NO. 1 SUSPENSION ARM RH |
 |
- HINT:
- Perform the same procedures as for the LH side.
| 17.
REMOVE REAR SUSPENSION MEMBER LOWER STOPPER LH |
 |
- Remove the 2 nuts and the rear suspension member lower stopper LH.
| 18.
REMOVE REAR SUSPENSION MEMBER LOWER STOPPER RH |
 |
- Remove the 2 nuts and the rear suspension member lower stopper RH.
| 19.
REMOVE REAR SUSPENSION MEMBER SUB-ASSEMBLY (w/ Sport Suspension) |
 |
- Support the rear suspension member with a jack.
Remove the 2 bolts and the 2 rear suspension member lower stoppers.
Remove the rear suspension member sub-assembly with the 4 differential support member cushions.
| 20.
REMOVE REAR SUSPENSION MEMBER SUB-ASSEMBLY |
 |
- Support the rear suspension member with a jack.
Remove the 2 bolts and the 2 rear suspension member lower stoppers.
Remove the rear suspension member sub-assembly.
| 21.
REMOVE REAR NO. 1 SUSPENSION ARM LH |
 |
- Remove the bolt and rear No. 1 suspension arm LH.