Illumination Circuit
Circuit diagnosis · Vehicles built Oct 2006 – May 2009
Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009
DESCRIPTION
Power is supplied to the navigation receiver assembly and steering pad switch illumination when the light control switch is in the tail or head position.WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- The vehicle is equipped with an SRS (Supplemental Restraint System) such as the airbags. Before servicing (including removal or installation of parts), be sure to read the precautionary notice for the Supplemental Restraint System (Click here).
| 1. CHECK ILLUMINATION |
Check if the illumination for the navigation receiver assembly, steering pad switch, glove box or others (Hazard switch, transmission control switch, etc.) comes on when the light control switch is turned to the HEAD or TAIL position.
- Result:
Condition
Proceed to
Illumination comes on for all components except steering pad switch.
A
Illumination comes on for all components except navigation receiver assembly.
B
No illumination comes on (navigation receiver assembly, hazard switch, glove box, etc.)
C
|
|
||||
|
|
||||
| A | |
| 2. CHECK HARNESS AND CONNECTOR (BATTERY - SPIRAL CABLE) |
Disconnect the spiral cable connector E18.

Measure the voltage according to the value(s) in the table below.
- Standard voltage:
Tester Connection
Condition
Specified Condition
E18-12 (IL+2) - Body ground
Light control switch tail or head
10 to 14 V
|
|
||||
| OK | |
| 3. CHECK STEERING PAD SWITCH ASSEMBLY |
Disconnect the steering pad switch assembly connector.


Connect the positive (+) lead to terminal ILL+ and the negative (-) lead to terminal EAU of the steering pad switch connector.
Check if the illumination for the steering pad switch comes on.
- OK:
- Illumination for the steering pad switch assembly comes on.
|
|
||||
| OK | |
| 4. INSPECT SPIRAL CABLE |
Disconnect the a1 steering pad switch and E18 spiral cable connectors.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Spiral cable position
Specified Condition
a1-8 (EAU) - E18-4 (EAU)
Center
Below 1 Ω
2.5 rotations to the left
2.5 rotations to the right
a1-5 (IL+2) - E18-12 (IL+2)
Center
Below 1 Ω
2.5 rotations to the left
2.5 rotations to the right
- NOTICE:
- The spiral cable is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may cause airbag deployment. Be sure to read the page shown in the brackets.
- HINT:
- Removal (Click here)
- Installation (Click here)
- Removal (Click here)
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - NAVIGATION RECEIVER ASSEMBLY) |
Disconnect the F38 navigation receiver assembly and E18 spiral cable connectors.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
F38-6 (SWG) - E18-4 (EAU)
Always
Below 1 Ω
F38-6 (SWG) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | ||
| ||
| 6. CHECK HARNESS AND CONNECTOR |
Disconnect the navigation receiver assembly connector F36.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
F36-7 (GND) - Body ground
Always
Below 1 Ω
Measure the voltage according to the value(s) in the table below.
- Standard voltage:
Tester Connection
Condition
Specified Condition
F36-10 (ILL+) - Body ground
Light control switch tail or head
10 to 14 V
|
|
||||
| OK | ||
| ||
