Light Control Switch Circuit
Circuit diagnosis · Vehicles built from Oct 2006
DESCRIPTION
The main body ECU receives the following switch information.- Light control switch position is OFF, TAIL, HEAD, or AUTO
- Dimmer switch position is HIGH, LOW, or HIGH FLASH (PASS)
- Fog light switch position is OFF or ON
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. READ VALUE USING INTELLIGENT TESTER |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the intelligent tester main switch on.
Select the items below in the DATA LIST, and read the displays on the intelligent tester.
Main Body (Main Body ECU): Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Dimmer Hi SW
Dimmer switch HIGH signal / ON or OFF
ON: Dimmer switch in HIGH
OFF: Dimmer switch in LOW
-
Passing Light SW
Dimmer switch FLASH signal / ON or OFF
ON: Dimmer switch in HIGH FLASH (PASS)
OFF: Dimmer switch not in HIGH FLASH (PASS)
-
Front Fog Light SW
Front fog light switch signal / ON or OFF
ON: Front fog light switch ON
OFF: Front fog light switch OFF
-
Light Auto SW
Light control switch AUTO signal / ON or OFF
ON: Light control switch in AUTO
OFF: Light control switch not in AUTO
-
Headlight SW
Light control switch HEAD signal / ON or OFF
ON: Light control switch in HEAD
OFF: Light control switch not in HEAD
-
Taillight SW
Light control switch TAIL signal / ON or OFF
ON: Light control switch in TAIL or HEAD
OFF: Light control switch in neither TAIL nor HEAD
-
- OK:
- Normal conditions listed above are displayed.
|
|
||||
| NG | |
| 2. INSPECT HEADLIGHT DIMMER SWITCH ASSEMBLY |
Inspect the headlight dimmer switch assembly (Click here).
|
|
||||
| OK | |
| 3. CHECK VEHICLE CONDITION |
- Result:
Vehicle Condition
Proceed to
LHD
A
RHD
B
|
|
||||
| A | |
| 4. CHECK HARNESS AND CONNECTOR (SWITCH - INSTRUMENT PANEL J/B AND BODY GROUND) |
Disconnect the E21 headlight dimmer switch assembly connector.

Disconnect the E6 and E7 main body ECU connectors.
Disconnect the IG instrument panel J/B connector.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
E21-4 (BFG) - E6-28 (FFOG)
Always
Below 1 Ω
E21-11 (HU) - IG-5 (HU)
Always
Below 1 Ω
E21-17 (HF) - E7-13 (HF)
Always
Below 1 Ω
E21-18 (T) - E7-23 (TAIL)
Always
Below 1 Ω
E21-20 (H) - E6-17 (HEAD)
Always
Below 1 Ω
E21-3 (LFG) - Body ground
Always
10 kΩ higher
E21-4 (BFG) - Body ground
Always
10 kΩ higher
E21-11 (HU) - Body ground
Always
10 kΩ higher
E21-17 (HF) - Body ground
Always
10 kΩ higher
E21-18 (T) - Body ground
Always
10 kΩ higher
E21-20 (H) - Body ground
Always
10 kΩ higher
E21-12 (EL) - Body ground
Always
Below 1 Ω
E21-3 (LFG) - Body ground
Always
Below 1 Ω
|
|
||||
| OK | ||
| ||
| 5. CHECK HARNESS AND CONNECTOR (SWITCH - INSTRUMENT PANEL J/B AND BODY GROUND) |
Disconnect the E21 headlight dimmer switch assembly connector.

Disconnect the E6 and E7 main body ECU connectors.
Disconnect the IG instrument panel J/B connector.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
E21-7 (BFG) - E6-28 (FFOG)
Always
Below 1 Ω
E21-11 (H) - E6-17 (HEAD)
Always
Below 1 Ω
E21-12 (A) - E7-21 (A)
Always
Below 1 Ω
E21-13 (T) - E7-23 (TAIL)
Always
Below 1 Ω
E21-14 (HF) - E7-13 (HF)
Always
Below 1 Ω
E21-20 (HU) - IG-5 (HU)
Always
Below 1 Ω
E21-7 (BFG) - Body ground
Always
10 kΩ higher
E21-11 (H) - Body ground
Always
10 kΩ higher
E21-12 (A) - Body ground
Always
10 kΩ higher
E21-13 (T) - Body ground
Always
10 kΩ higher
E21-14 (HF) - Body ground
Always
10 kΩ higher
E21-20 (HU) - Body ground
Always
10 kΩ higher
E21-19 (EL) - Body ground
Always
Below 1 Ω
E21-8 (LFG) - Body ground
Always
Below 1 Ω
|
|
||||
| OK | ||
| ||
