2006-2011 Camry Aurion · Service Manual BODY ELECTRICAL

Speaker Circuit

Circuit diagnosis · Vehicles built from Jun 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

The sound signals amplified by the stereo component amplifier are sent to the speakers from the stereo component amplifier through this circuit.
If there is a short in this circuit, the stereo component amplifier detects it and stops output to the speakers.
Thus sound cannot be heard from the speakers even if there is no malfunction in the stereo component amplifier or speakers.
If a short is detected in the speaker circuit, no sound can be heard from the speakers.

WIRING DIAGRAM

E193060E01

INSPECTION PROCEDURE


1. CHECK HARNESS AND CONNECTOR
  1. Disconnect the F36 navigation receiver assembly connector.

  1. Disconnect the F37 navigation receiver assembly connector.

  1. Disconnect the H1 and I1 front No. 1 speaker connectors.

  1. Disconnect the F47 and F48 front No. 2 speaker connectors.

  1. Disconnect the O12 and O13 rear speaker connectors.

  1. Disconnect the F46 stereo component amplifier assembly connector.

  1. Disconnect the N46 mayday ECU connector.

  1. Measure the resistance between each of the front No. 2 speakers and the navigation receiver assembly to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F36-2 (FL+) - F47-2 (TWL+)
    Always
    Below 1 Ω
    F36-6 (FL-) - F47-4 (TWL-)
    Always
    Below 1 Ω
    F36-1 (FR+) - F48-2 (TWR+)
    Always
    Below 1 Ω
    F36-5 (FR-) - F48-4 (TWR-)
    Always
    Below 1 Ω

  1. Measure the resistance between each of the front No. 2 speakers and the stereo component amplifier assembly to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F47-1 (+) - F46-1 (RL+)
    Always
    Below 1 Ω
    F47-3 (-) - F46-6 (RL-)
    Always
    Below 1 Ω
    F48-1 (+) - F46-2 (RR+)
    Always
    Below 1 Ω
    F48-3 (-) - F46-7 (RR-)
    Always
    Below 1 Ω

  1. w/o TOYOTA Link SystemMeasure the resistance between each of the rear speakers and the navigation receiver assembly to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F37-2 (RL+) - O12-1
    Always
    Below 1 Ω
    F37-6 (RL-) - O12-2
    Always
    Below 1 Ω
    F37-1 (RR+) - O13-1
    Always
    Below 1 Ω
    F37-3 (RR-) - O13-2
    Always
    Below 1 Ω

  1. w/ TOYOTA Link SystemMeasure the resistance between each of the rear speakers, the mayday ECU and the navigation receiver assembly to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F37-2 (RL+) - N46-25 (SPI+)
    Always
    Below 1 Ω
    F37-6 (RL-) - N46-24 (SPI-)
    Always
    Below 1 Ω
    F37-1 (RR+) - O13-1
    Always
    Below 1 Ω
    F37-3 (RR-) - O13-2
    Always
    Below 1 Ω
    N46-23 (SPO+) - O12-1
    Always
    Below 1 Ω
    N46-22 (SPO-) - O12-2
    Always
    Below 1 Ω

  1. Measure the resistance between each of the front No. 1 speakers and the stereo component amplifier assembly to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I1-1 - F46-4 (WFL+)
    Always
    Below 1 Ω
    I1-2 - F46-11 (WFL-)
    Always
    Below 1 Ω
    H1-1 - F46-3 (WFR+)
    Always
    Below 1 Ω
    H1-2 - F46-8 (WFR-)
    Always
    Below 1 Ω

  1. Measure the resistance between each speaker and body ground to check for a short circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F47-1 (+) - Body ground
    Always
    10 kΩ or higher
    F47-3 (-) - Body ground
    Always
    10 kΩ or higher
    F47-2 (TWL+) - Body ground
    Always
    10 kΩ or higher
    F47-4 (TWL-) - Body ground
    Always
    10 kΩ or higher
    F48-1 (+) - Body ground
    Always
    10 kΩ or higher
    F48-3 (-) - Body ground
    Always
    10 kΩ or higher
    F48-2 (TWR+) - Body ground
    Always
    10 kΩ or higher
    F48-4 (TWR-) - Body ground
    Always
    10 kΩ or higher
    O12-1 - Body ground
    Always
    10 kΩ or higher
    O12-2 - Body ground
    Always
    10 kΩ or higher
    O13-1 - Body ground
    Always
    10 kΩ or higher
    O13-2 - Body ground
    Always
    10 kΩ or higher
    I1-1 - Body ground
    Always
    10 kΩ or higher
    I1-2 - Body ground
    Always
    10 kΩ or higher
    H1-1 - Body ground
    Always
    10 kΩ or higher
    H1-2 - Body ground
    Always
    10 kΩ or higher

  1. w/ TOYOTA Link SystemMeasure the resistance between the mayday ECU and body ground to check for a short circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    N46-22 (SPO-) - Body ground
    Always
    10 kΩ or higher
    N46-23 (SPO+) - Body ground
    Always
    10 kΩ or higher
    N46-24 (SPI-) - Body ground
    Always
    10 kΩ or higher
    N46-25 (SPI+) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. INSPECT FRONT NO. 1 SPEAKER

  1. E165683E18
    Resistance check
    1. Measure the resistance between the terminals of the speaker.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      I1-1 - I1-2
      Always
      1.6 to 2.4 Ω
      H1-1 - H1-2
      Always
      1.6 to 2.4 Ω

      NOTICE:
      The speaker should not be removed to check resistance.

      Text in Illustration 
      *1
      Component without harness connected
      (Front No. 1 Speaker)



NG
REPLACE FRONT NO. 1 SPEAKER (Click here)
OK


3. INSPECT FRONT NO. 2 SPEAKER

  1. E177897E12
    Resistance check
    1. Measure the resistance between the terminals of the speaker.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      F47-1 (+) - F47-2 (TWL+)
      Always
      Below 1 Ω
      F47-3 (-) - F47-4 (TWL-)
      Always
      Below 1 Ω
      F48-1 (+) - F48-2 (TWR+)
      Always
      Below 1 Ω
      F48-3 (-) - F48-4 (TWR-)
      Always
      Below 1 Ω

      NOTICE:
      The speaker should not be removed to check resistance.

      Text in Illustration 
      *1
      Component without harness connected
      (Front No. 2 Speaker)



NG
REPLACE FRONT NO. 2 SPEAKER (Click here)
OK


4. INSPECT FRONT NO. 2 SPEAKER
  1. Check that the malfunction disappears when another speaker in good condition is installed.

    Standard:
    Malfunction disappears.

    HINT:
    1. Connect all the connectors to the front No. 2 speakers that were disconnected.
    2. If there is a possibility that either the right or left front No. 2 speaker is defective, inspect by interchanging the right one with the left one.
    3. Perform the above inspection on both LH and RH sides.



NG
Go to step 5
OK

REPLACE FRONT NO. 2 SPEAKER (Click here)

5. INSPECT REAR SPEAKER
  1. Check that the malfunction disappears when another speaker in good condition is installed.

    Standard:
    Malfunction disappears.

    HINT:
    1. Connect all the connectors to the rear speakers that were disconnected.
    2. If there is a possibility that either the right or left rear speaker is defective, inspect by interchanging the right one with the left one.
    3. Perform the above inspection on both LH and RH sides.



NG
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)
OK

REPLACE REAR SPEAKER (Click here)


← Speaker Circuit (Oct 2006 – May 2009)Sound Signal Circuit between Navigation Receiver Assembly and Stereo Jack Adapter (from Jun 2009) →