2006-2011 Camry Aurion · Service Manual BODY ELECTRICAL

Speaker Circuit

Circuit diagnosis · Vehicles built from Jun 2009

DESCRIPTION

If there is a short in this circuit, the radio and display assembly detects it and stops output to the speakers.
Thus sound cannot be heard from the speakers even if there is no malfunction in the radio and display assembly or speakers.
If a short is detected in the speaker circuit, no sound can be heard from the speakers.

WIRING DIAGRAM

E185274E16

INSPECTION PROCEDURE


1. CHECK HARNESS AND CONNECTOR
  1. Disconnect the F6 radio and display assembly connector.

  1. Disconnect the F7 radio and display assembly connector.

  1. Disconnect the I1 and H1 front No. 1 speaker connectors.

  1. Disconnect the F21 and F23 front No. 2 speaker connectors.

  1. Disconnect the O12 and O13 rear speaker connectors.

  1. Measure the resistance between each of the front No. 2 speakers and the radio and display assembly to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F6-2 (FL+) - F21-2 (TWL+)
    Always
    Below 1 Ω
    F6-6 (FL-) - F21-4 (TWL-)
    Always
    Below 1 Ω
    F6-1 (FR+) - F23-2 (TWR+)
    Always
    Below 1 Ω
    F6-5 (FR-) - F23-4 (TWR-)
    Always
    Below 1 Ω

  1. Measure the resistance between each of the front No. 2 speakers and the front No. 1 speakers to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F21-1 (+) - I1-1
    Always
    Below 1 Ω
    F21-3 (-) - I1-2
    Always
    Below 1 Ω
    F23-1 (+) - H1-1
    Always
    Below 1 Ω
    F23-3 (-) - H1-2
    Always
    Below 1 Ω

  1. Measure the resistance between each of the rear speakers and the radio and display assembly to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F7-2 (RL+) - O12-1
    Always
    Below 1 Ω
    F7-6 (RL-) - O12-2
    Always
    Below 1 Ω
    F7-1 (RR+) - O13-1
    Always
    Below 1 Ω
    F7-3 (RR-) - O13-2
    Always
    Below 1 Ω

  1. Measure the resistance between each speaker and body ground to check for a short circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F21-1 (+) - Body ground
    Always
    10 kΩ or higher
    F21-3 (-) - Body ground
    Always
    10 kΩ or higher
    F21-2 (TWL+) - Body ground
    Always
    10 kΩ or higher
    F21-4 (TWL-) - Body ground
    Always
    10 kΩ or higher
    F23-1 (+) - Body ground
    Always
    10 kΩ or higher
    F23-3 (-) - Body ground
    Always
    10 kΩ or higher
    F23-2 (TWR+) - Body ground
    Always
    10 kΩ or higher
    F23-4 (TWR-) - Body ground
    Always
    10 kΩ or higher
    O12-1 - Body ground
    Always
    10 kΩ or higher
    O12-2 - Body ground
    Always
    10 kΩ or higher
    O13-1 - Body ground
    Always
    10 kΩ or higher
    O13-2 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. INSPECT FRONT NO. 1 SPEAKER

  1. E165683E18
    Resistance check
    1. Measure the resistance between the terminals of the speaker.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      I1-1 - I1-2
      Always
      3.2 to 4.8 Ω
      H1-1 - H1-2
      Always
      3.2 to 4.8 Ω

      NOTICE:
      The speaker should not be removed to check resistance.

      Text in Illustration 
      *1
      Component without harness connected
      (Front No. 1 Speaker)



NG
REPLACE FRONT NO. 1 SPEAKER (Click here)
OK


3. INSPECT FRONT NO. 2 SPEAKER

  1. E185295E07
    Resistance check
    1. Measure the resistance between the terminals of the speaker.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      F21-1 (+) - F21-2 (TWL+)
      Always
      Below 1 Ω
      F21-3 (-) - F21-4 (TWL-)
      Always
      Below 1 Ω
      F23-1 (+) - F23-2 (TWR+)
      Always
      Below 1 Ω
      F23-3 (-) - F23-4 (TWR-)
      Always
      Below 1 Ω

      NOTICE:
      The speaker should not be removed to check resistance.

      Text in Illustration 
      *1
      Component without harness connected
      (Front No. 2 Speaker)



NG
REPLACE FRONT NO. 2 SPEAKER (Click here)
OK


4. INSPECT FRONT NO. 2 SPEAKER
  1. Check that the malfunction disappears when another speaker in good condition is installed.

    Standard:
    Malfunction disappears.

    HINT:
    1. Connect all the connectors to the front No. 2 speakers that were disconnected.
    2. If there is a possibility that either the right or left front speaker is defective, inspect by interchanging the right one with the left one.
    3. Perform the above inspection on both LH and RH sides.



NG
Go to step 5
OK

REPLACE FRONT NO. 2 SPEAKER (Click here)

5. INSPECT REAR SPEAKER

  1. E185294E01
    Resistance check
    1. Measure the resistance between the terminals of the speaker.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      O12-1 - O12-2
      Always
      3.2 to 4.8 Ω
      O13-1 - O13-2
      Always
      3.2 to 4.8 Ω

      NOTICE:
      The speaker should not be removed to check resistance.

      Text in Illustration 
      *1
      Component without harness connected
      (Rear Speaker)



NG
REPLACE REAR SPEAKER (Click here)
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)


← Parking Brake Switch Circuit (from Jun 2009)Radio Receiver Power Source Circuit (from Jun 2009) →