2006-2011 Camry Aurion · Service Manual BODY ELECTRICAL

Unlock Warning Switch Circuit

Circuit diagnosis · Vehicles built Oct 2006 – May 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

The unlock warning switch detects if the key is in the ignition key cylinder.
The unlock warning switch turns on when the key is inserted into the ignition key cylinder and turns off when the key is removed from the cylinder.
The main body ECU (instrument panel J/B) is connected to the unlock warning switch via terminal KSW and key detection status signals are input to the main body ECU (instrument panel J/B).
The main body ECU (instrument panel J/B) applies voltage to the unlock warning switch via terminal KSW. When the unlock warning switch is on (there is continuity between the switch terminals), a signal indicating that the key is in the ignition key cylinder is input to the main body ECU (instrument panel J/B). When the switch is off (there is no continuity between the switch terminals), a signal indicating that the key is not in the cylinder is input.

WIRING DIAGRAM

B128326E07

INSPECTION PROCEDURE


1. READ VALUE USING INTELLIGENT TESTER

  1. B139188E02
    Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to the ON position and turn the intelligent tester main switch on.

  1. Select Key Unlock Warning SW in the Data List and read the tester display.

    BODY: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Key Unlock Warning SW
    Unlock warning switch signal
    /ON or OFF
    ON: Key is in ignition key cylinder
    OFF: No key is in ignition key cylinder
    -

    OK:
    ON (Key is in ignition key cylinder) appears on the screen.



OK
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)
NG


2. INSPECT UNLOCK WARNING SWITCH ASSEMBLY

  1. B118535E03
    Remove the unlock warning switch assembly (Click herefor 2AZ-FE, Click here for 2GR-FE).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Switch free (Key removed)
    10 kΩ or higher
    1 - 2
    Switch pushed (Key set)
    Below 1 Ω

    Result:
    Result
    Proceed to
    NG (for 2AZ-FE)
    A
    NG (for 2GR-FE)
    B
    OK
    C



A
REPLACE UNLOCK WARNING SWITCH ASSEMBLY (2AZ-FE) (Click here)

B
REPLACE UNLOCK WARNING SWITCH ASSEMBLY (2GR-FE) (Click here)
C


3. CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH - MAIN BODY ECU)

  1. B139168E02
    Disconnect the E22 switch and E9 ECU connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E22-1 - E9-5 (KSW)
    Always
    Below 1 Ω
    E22-1 - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH - BODY GROUND)

  1. B139172E01
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E22-2 - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)


← Unlock Warning Switch Circuit (Jun 2006 – Sep 2006)Unlock Warning Switch Circuit (from Jun 2009) →