ON-VEHICLE INSPECTION
Inspection · Vehicles built Jun 2006 – Sep 2006
Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009
| INSPECT SPEEDOMETER |
Check the operation.
Using a speedometer tester (calibrated chassis dynamometer), check the speedometer indication according to the table below.
Reference: Chassis dynamometer indication
Acceptable range
Data in ( ) is for reference
20 km/h
(21.0 to 25.0 km/h)
40 km/h
41.7 to 46.2 km/h
60 km/h
62.7 to 67.2 km/h
80 km/h
83.4 to 88.4 km/h
100 km/h
104.3 to 109.3 km/h
120 km/h
125.1 to 130.6 km/h
140 km/h
145.8 to 151.8 km/h
160 km/h
166.2 to 173.2 km/h
180 km/h
186.9 to 194.5 km/h
200 km/h
207.7 to 215.7 km/h
220 km/h
228.4 to 236.8 km/h
240 km/h
249.2 to 258.0 km/h
- NOTICE:
- Tire wear as well as over or under inflation will cause errors.
Check the deviation from the acceptable range of the speedometer indication.
- Reference:
- Less than 1.75 km/h (1.09 mph)
- HINT:
- If the indication is not as specified, go to problem symptoms table (Click here).
| INSPECT TACHOMETER |
Connect a tune-up tachometer, and start the engine.
Compare the test results with the tachometer indications.
DC 13.5 V, at 25°C (77°F) Tune-up tachometer indication (rpm)
Acceptable range
Data in ( ) is for reference
700
630 to 770
1,000
(900 to 1,100)
2,000
(1,850 to 2,150)
3,000
2,800 to 3,200
4,000
(3,800 to 4,200)
5,000
4,800 to 5,200
6,000
(5,750 to 6,250)
7,000
6,700 to 7,300
8,000
(7,700 to 8,300)
- HINT:
- If the indication is not as specified, go to the problem symptoms table (Click here).
| INSPECT ENGINE COOLANT TEMPERATURE RECEIVER GAUGE |
Turn the ignition switch to the ON position.
Check the needle indication according to the condition in the table below.

- OK:
Condition
Specified Condition
Before warming up
The gauge needle indicates C (COOL)
- HINT:
- The conditions described above is before the engine has been warmed up.
Start the engine.
Wait until the engine has been warmed up.
- HINT:
- The engine coolant temperature is 78 to 105°C (172 to 221°F) (*1)/95 to 105°C (203 to 221°F) (*2) after warming up. The current engine coolant temperature can be seen in the Data List (Click here).
Check the needle indication according to the condition in the table below.
- OK:
Condition
Specified Condition
After warming up
The gauge needle indicates (*) shown in the illustration
*2: for G.C.C. Countries
| INSPECT ENGINE OIL PRESSURE SWITCH |
Disconnect the connector from the engine oil pressure switch.
Turn the ignition switch to the ON position.
Ground the terminal of the wire harness side connector.
Turn the ignition switch to the ON position, and engine idling for 10 seconds or more.
- OK:
- The warning light comes on.
- HINT:
- If the warning light does not come on, go to the problem symptoms table (Click here).
