2006-2011 Camry Aurion · Service Manual TRANSMISSION

INSTALLATION

Removal / installation · Vehicles built Oct 2006 – May 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009


1. INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY
  1. Move the shift lever to the N position.

  1. C135733E01
    Align the protrusions of the park/neutral position switch.

  1. C135732
    Install the park/neutral position switch to the control shaft with the 2 bolts.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

    NOTICE:
    1. Before installing the park/neutral position switch, remove any dirt or rust on the control shaft. Be sure to install the switch straight along the shaft while being careful not to deform the plate spring that supports the shaft. If the plate spring is deformed, the park/neutral position switch cannot be reinstalled correctly.
    2. After installing the park/neutral position switch, confirm that the 2 protrusions on the switch are aligned.

  1. C136685
    Install the control shaft lever to the control shaft with the nut and washer.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

  1. Connect the connector to the park/neutral position switch.

  1. C132237
    Connect the transmission control cable to the transmission control cable bracket with a new clip.

  1. C132236
    Connect the transmission control cable to the control shaft lever with the nut.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }


2. INSTALL AIR CLEANER BRACKET

  1. C132235
    Install the air cleaner bracket with the 3 bolts.

    Torque:
    7.8 N*m{ 80 kgf*cm , 69 in.*lbf }

  1. Install the wire harness clamp.


3. INSTALL NO. 1 AIR CLEANER INLET

  1. A132970
    Install the No. 1 air cleaner inlet with the bolt.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }


4. INSTALL AIR CLEANER CASE SUB-ASSEMBLY

  1. A132971
    Install the air cleaner case with the 3 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Connect the vacuum hose and hose clamp.


5. INSTALL AIR CLEANER CAP SUB-ASSEMBLY

  1. A135706
    Install the air cleaner cap sub-assembly, and connect the 3 bands.

  1. A135705E01
    Connect the mass air flow meter connector (*1).

  1. Connect the No. 2 ventilation hose (*2).

  1. Connect the hose band (*3).

  1. A135704
    Connect the 3 vacuum hoses.


6. INSTALL AIR CLEANER INLET ASSEMBLY

  1. A132969
    Install the air cleaner inlet with the clamp and 2 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }


7. INSTALL COOL AIR INTAKE DUCT SEAL

  1. A141576E01
    Install the intake duct seal with the 7 clips.


8. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
6.9 N*m{ 70 kgf*cm , 61 in.*lbf }


9. INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY OPERATION
  1. Apply the parking brake.

  1. Turn the ignition switch on (IG).

  1. Depress the brake pedal and check that the engine starts when the shift lever is set in the N or P position, but does not start in other positions.

  1. Check that the back-up light comes on only when the shift lever is set in the R position, but the light does not operate in other positions. If a failure is found, check the park/neutral position switch for continuity.


10. INSPECT SHIFT LEVER POSITION
  1. When shifting from the P to the R position with the ignition switch on (IG) and the brake pedal depressed, make sure that the shift lever moves smoothly and moves correctly into position.

  1. Start the engine and make sure that the vehicle moves forward when shifting from the N to the D position and moves rearward when shifting to the R position.
    If operation cannot be done as specified, inspect the park/neutral position switch assembly and check the shift lever assembly installation condition.


11. ADJUST SHIFT LEVER POSITION
  1. Remove the cool air intake duct seal (Click here).

  1. Remove the air cleaner inlet assembly (Click here).

  1. Remove the air cleaner cap sub-assembly (Click here).

  1. Remove the air cleaner case sub-assembly (Click here).

  1. Remove the No. 1 air cleaner inlet (Click here).

  1. Move the shift lever to the N position.

  1. C132236
    Remove the nut and transmission control cable from the control shaft lever.

  1. C135733E01
    Align the protrusions of the park/neutral position switch.

  1. C135734E02
    Move the slider in the direction indicated by arrow A and pull up the lock piece in the direction indicated by arrow B.

    NOTICE:
    Do not damage the boot.

  1. C132236
    Install the transmission control cable assembly to the control shaft with the nut.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

    NOTICE:
    1. If the control cable end is excessively pushed up, the shift lever cannot be adjusted.
    2. When tightening the nut, confirm that the control cable is properly stretched.

  1. C138300E01
    Push in the lock piece.

    NOTICE:
    Firmly push in the lock piece until the slider lock is engaged.

  1. Install the No. 1 air cleaner inlet (Click here).

  1. Install the air cleaner case sub-assembly (Click here).

  1. Install the air cleaner cap sub-assembly (Click here).

  1. Install the air cleaner inlet assembly (Click here).

  1. Install the cool air intake duct seal (Click here).

  1. Start the engine and make sure that the vehicle moves forward when moving the lever from the N to the D position and moves rearward when moving it to the R position. If it becomes hard to move the shift lever, readjust the shift lever position.

← INSPECTION (from Oct 2006)INSTALLATION (from Jun 2009) →