2006-2011 Camry Aurion · Service Manual ENGINE

DISASSEMBLY

Removal / installation · Vehicles built from Jun 2009

Versions by build date: Jun 2006 – May 2009 from Jun 2009


1. REMOVE GENERATOR PULLEY (w/o Generator Clutch Pulley)

  1. A219109E02
    While holding SST 1-A with a torque wrench, tighten SST 1-B clockwise to the specified torque.
    SST
    09820-63010   (09820-06010, 09820-06020)

    HINT:
    SST 1-A and B
    09820-06010
    SST 2
    09820-06020

    Torque:
    39 N*m{ 400 kgf*cm , 29 ft.*lbf }

    NOTICE:
    Firmly secure SST on the generator rotor shaft.

  1. A219108E01
    Place the rotor shaft end into SST 1-A and B.

  1. Fit SST 2 to the generator pulley.

  1. Loosen the pulley by turning SST 1-A and B in the direction shown in the illustration.

    NOTICE:
    1. Check that the drive end frame is secured in the vise tightly.
    2. Hold SST 2 tightly during the operation.

  1. Remove the generator from SST 2.

  1. A145796E02
    While holding SST 1-B, turn SST 1-A and remove SST 1-A and 1-B.

  1. Remove the pulley nut, then remove the generator pulley.


2. REMOVE GENERATOR CLUTCH PULLEY (w/ Generator Clutch Pulley)

  1. A215198
    Using a screwdriver, puncture the center of the generator pulley cap and pry it off.

    NOTICE:
    Do not reuse the generator pulley cap.

  1. A197237E01
    Mount the generator in a vise.

  1. Install SST (A) and (B) to the pulley as shown in the illustration.

    SST
    09820-63021  

  1. A197239E01
    Use a wrench to hold SST (A), and turn SST (B) counterclockwise to loosen the generator clutch pulley.

    NOTICE:
    1. Check that the drive end frame is secured in the vise tightly.
    2. Hold SST (A) tightly during the operation.

  1. Remove the generator clutch pulley.


3. REMOVE GENERATOR REAR END COVER
  1. Place the generator drive end frame on the pulley.

  1. A128610
    Remove the 3 nuts and rear end cover.


4. REMOVE GENERATOR TERMINAL INSULATOR

  1. A128609
    Remove the terminal insulator.


5. REMOVE GENERATOR BRUSH HOLDER ASSEMBLY

  1. A128611
    Remove the 2 screws and generator brush holder.


6. REMOVE GENERATOR ROTOR ASSEMBLY

  1. A128612
    Remove the 4 bolts.

  1. A128613
    Remove the bolt and cord clip.

  1. A128614E01
    Using SST, remove the coil.
    SST
    09950-40011   (09951-04020, 09952-04010, 09953-04020, 09954-04010, 09955-04071, 09957-04010, 09958-04011)


7. REMOVE GENERATOR ROTOR ASSEMBLY

  1. A118365E01
    Remove the washer.

  1. A128615
    Remove the generator rotor.


8. REMOVE GENERATOR DRIVE END FRAME BEARING

  1. A128617
    Remove the 4 screws and retainer plate.

  1. A128618E01
    Using SST and a hammer, tap out the bearing.
    SST
    09950-60010   (09951-00250)
    09950-70010   (09951-07100)

← DISASSEMBLY (Jun 2006 – May 2009)INSPECTION (Jun 2006 – May 2009) →