2006-2011 Camry Aurion · Service Manual ENGINE

REASSEMBLY

Removal / installation · Vehicles built from Jun 2009

Versions by build date: Jun 2006 – May 2009 from Jun 2009


1. INSTALL GENERATOR DRIVE END FRAME BEARING

  1. A128619E01
    Using SST and a press, press in a new generator drive end frame bearing.
    SST
    09950-60010   (09951-00250)
    09950-70010   (09951-07100)

  1. A128620E01
    Fit the tabs on the retainer plate into the cutouts on the drive end frame to install the retainer plate.

  1. Install the 4 screws.

    Torque:
    2.3 N*m{ 23 kgf*cm , 20 in.*lbf }


2. INSTALL GENERATOR ROTOR ASSEMBLY
  1. Place the drive end frame on the pulley.

  1. A128615
    Install the generator rotor onto the generator end frame.

  1. A118365E01
    Place a new generator washer on the generator rotor.


3. INSTALL GENERATOR COIL ASSEMBLY

  1. A128621E01
    Using SST and a press, press in the generator coil assembly to the drive end frame.
    SST
    09612-70100   (09612-07240)

  1. A128612
    Tighten the 4 bolts.

    Torque:
    5.9 N*m{ 60 kgf*cm , 52 in.*lbf }

  1. A128613
    Install the cord clip with the bolt.

    Torque:
    4.6 N*m{ 47 kgf*cm , 41 in.*lbf }


4. INSTALL GENERATOR BRUSH HOLDER ASSEMBLY

  1. A079315E04
    While pushing the 2 brushes into the generator brush holder, insert a 1.0 mm (0.0393 in.) diameter pin into the generator brush holder.

  1. A128622
    Install the generator brush holder with the 2 screws.

    Torque:
    1.8 N*m{ 18 kgf*cm , 16 in.*lbf }

  1. A130537E01
    Pull the pin out of the generator brush holder.


5. INSTALL GENERATOR TERMINAL INSULATOR

  1. A128623
    Install the terminal insulator onto the generator coil assembly.


6. INSTALL GENERATOR REAR END COVER

  1. A128610
    Install the generator rear end cover with the 3 nuts.

    Torque:
    4.6 N*m{ 47 kgf*cm , 41 in.*lbf }


7. INSTALL GENERATOR PULLEY (w/o Generator Clutch Pulley)
  1. Temporarily install the generator pulley with the pulley nut.

  1. A219109E02
    While holding SST 1-A with a torque wrench, tighten SST 1-B clockwise to the specified torque.
    SST
    09820-63010   (09820-06010, 09820-06020)

    HINT:
    SST 1-A and B
    09820-06010
    SST 2
    09820-06020

    Torque:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }

    NOTICE:
    Firmly secure SST on the generator rotor shaft.

  1. A219108E01
    Place the rotor shaft end into SST 1-A and B.

  1. Fit SST 2 to the generator pulley.

  1. Tighten the pulley by turning SST 2 in the direction shown in the illustration.

    Torque:
    111 N*m{ 1132 kgf*cm , 82 ft.*lbf }

    NOTICE:
    1. This torque value is effective when SST is parallel to the torque wrench.
    2. Check that the drive end frame is secured in the vise tightly.
    3. Hold SST 1-A and B tightly during the operation.

  1. Remove the generator from SST 2.

  1. A145796E02
    While holding SST 1-B, turn SST 1-A and remove SST 1-A and 1-B.

  1. Turn the generator pulley, then check that the generator pulley moves smoothly.


8. INSTALL GENERATOR CLUTCH PULLEY (w/ Generator Clutch Pulley)
  1. Temporarily install the generator clutch pulley.

  1. Mount the generator in a vise.

  1. A219106E01
    Install SST (A) and (B) to the generator clutch pulley as shown in the illustration.
    SST
    09820-63021  

  1. A219107E01
    Using a wrench to hold SST (A), turn SST (B) clockwise to tighten the generator clutch pulley.

    Torque:
    without SST:
    111 N*m{ 1132 kgf*cm , 82 ft.*lbf }
    with SST:
    80 N*m{ 816 kgf*cm , 59 ft.*lbf }

    NOTICE:
    1. Use a torque wrench with a fulcrum length of 260 mm (10.24 in.).
    2. This torque value is effective when SST is parallel to a torque wrench.
    3. Check that the drive end frame is secured in the vise tightly.
    4. Hold SST (A) tightly during the operation.

  1. Check that the generator pulley rotates smoothly.

  1. A219105
    Install a new generator pulley cap to the pulley.

← REASSEMBLY (Jun 2006 – May 2009)INSTALLATION (Jun 2006 – Sep 2006) →