2006-2011 Camry Aurion · Service Manual ENGINE

REASSEMBLY

Removal / installation · Vehicles built Jun 2006 – May 2009

Versions by build date: Jun 2006 – May 2009 from Jun 2009


1. INSTALL GENERATOR DRIVE END FRAME BEARING

  1. A128619E01
    Using SST and a press, press in a new generator drive end frame bearing.
    SST
    09950-60010   (09951-00250)
    09950-70010   (09951-07100)

  1. A128620E01
    Fit the tabs on the retainer plate into the cutouts on the drive end frame to install the retainer plate.

  1. Install the 4 screws.

    Torque:
    2.3 N*m{ 23 kgf*cm , 20 in.*lbf }


2. INSTALL GENERATOR ROTOR ASSEMBLY
  1. Place the drive end frame on the clutch pulley.

  1. A128615
    Install the generator rotor onto the generator rectifier end frame.

  1. A118365E01
    Place a new generator washer on the generator rotor.


3. INSTALL GENERATOR COIL ASSEMBLY

  1. A128621E01
    Using SST and a press, press in the generator coil assembly to the drive end frame.
    SST
    09612-70100   (09612-07240)

  1. A128612
    Tighten the 4 bolts.

    Torque:
    5.8 N*m{ 59 kgf*cm , 51 in.*lbf }

  1. A128613
    Install the cord clip with the bolt.

    Torque:
    4.6 N*m{ 47 kgf*cm , 41 in.*lbf }


4. INSTALL GENERATOR BRUSH HOLDER ASSEMBLY

  1. A079315E04
    While pushing the 2 brushes into the generator brush holder, insert a 1.0 mm (0.039 in.) pin into the generator brush holder.

  1. A128622
    Install the generator brush holder with the 2 screws.

    Torque:
    1.8 N*m{ 18 kgf*cm , 16 in.*lbf }

  1. A130537E01
    Pull the pin out of the generator brush holder.


5. INSTALL GENERATOR TERMINAL INSULATOR

  1. A128623
    Install the terminal insulator onto the generator rectifier end frame.


6. INSTALL GENERATOR REAR END COVER

  1. A128610
    Install the generator rear end cover with the 3 nuts.

    Torque:
    4.6 N*m{ 47 kgf*cm , 41 in.*lbf }


7. INSTALL GENERATOR PULLEY
SST
09820-63010   (09820-06010, 09820-06020)
Item
Part No.
SST 1-A and B
09820-06010
SST 2
09820-06020
  1. Install the pulley to the rotor shaft by tightening the generator pulley nut by hand.

  1. A219109E02
    While holding SST 1-A with a torque wrench, tighten SST 1-B clockwise to the specified torque.

    Torque:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }

    NOTICE:
    Check that the SST is secured to the rotor shaft.

  1. Mount SST 2 in a vise.

  1. A075665E02
    Insert SST 1-A and B into SST 2, and attach the pulley nut to SST 2.

  1. A145797E02
    Tighten the pulley nut by turning SST 1-A in the direction shown in the illustration.

    Torque:
    111 N*m{ 1130 kgf*cm , 82 ft.*lbf }

  1. Remove the generator from SST 2.

  1. A145796E02
    While holding SST 1-B, turn SST 1-A and remove SST 1-A and 1-B.

  1. Turn the pulley, and check that the pulley moves smoothly.

← INSPECTION (from Jun 2009)REASSEMBLY (from Jun 2009) →