2006-2011 Camry Aurion · Service Manual TRANSMISSION

INSTALLATION

Removal / installation · Vehicles built from Jun 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009


1. INSTALL CLUTCH MASTER CYLINDER ASSEMBLY (for LHD)

  1. C135416
    Install a new gasket to the clutch master cylinder assembly.

  1. Install the clutch master cylinder with the 2 nuts.

    Torque:
    12 N*m{ 120 kgf*cm , 9 ft.*lbf }


2. INSTALL CLUTCH MASTER CYLINDER ASSEMBLY (for RHD)

  1. C135417
    Install a new gasket to the clutch master cylinder assembly.

  1. Install the clutch master cylinder with the 2 nuts.

    Torque:
    12 N*m{ 120 kgf*cm , 9 ft.*lbf }


3. CONNECT CLUTCH LINE

C135419E01
  1. Using SST, connect the clutch line.

    SST
    09023-00101  

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }


4. CONNECT CLUTCH RESERVOIR TUBE

  1. C135418E01
    Connect the clutch reservoir tube to the clutch master cylinder with the clip.

    NOTICE:
    1. Connect the clutch reservoir tube so that it will not be twisted.
    2. Make sure that the green mark is positioned as shown in the illustration.


5. CONNECT CLUTCH MASTER CYLINDER PUSH ROD CLEVIS

C135428E01
  1. Apply MP grease to the contact surface of the pin and clevis bushing.

  1. Connect the clevis pin to the clutch pedal with the pin and a new clip.

    HINT:
    Install the pin from the left side of the vehicle.


6. INSTALL BRAKE BOOSTER ASSEMBLY

  1. C132719
    Install the brake booster assembly and the gasket with the 4 nuts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

    NOTICE:
    Do not damage the brake lines.


7. INSTALL COMBINATION METER ASSEMBLY

  1. B152781E01
    Connect each connector.

  1. Install the combination meter assembly with the 4 screws <E>.


8. INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY

  1. B133985E01
    Engage the guide and the 4 claws.

  1. Install the instrument cluster finish panel sub-assembly with the 2 clips.


9. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL

  1. B144612
    Engage the 2 claws and 2 clips to install the lower instrument panel finish panel.


10. INSTALL NO. 1 INSTRUMENT PANEL SUB-ASSEMBLY (for LHD)
  1. Connect each connector.

  1. B149938
    Engage the 3 claws and 2 clips to install the No. 1 instrument panel sub-assembly.


11. INSTALL NO. 1 INSTRUMENT PANEL SUB-ASSEMBLY (for RHD)
  1. Connect each connector.

  1. B149938
    Engage the 3 claws and 2 clips to install the No. 1 instrument panel sub-assembly.


12. INSTALL LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL

  1. B147264E01
    Install the air hose and connect the connector.

  1. Engage the 2 claws and the DLC3.

  1. Engage the claw and the 4 clips.

  1. Install the lower No. 1 instrument panel finish panel with the screw <B> and bolt <A>.


13. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH

  1. B132116E01
    Engage the 2 clips.

  1. Install the cowl side trim sub-assembly LH with the cowl side trim clip.


14. INSTALL FRONT DOOR SCUFF PLATE LH

HINT:
Use the same procedure for the RH side and the LH side.


15. INSTALL COWL TOP OUTER FRONT PANEL SUB-ASSEMBLY

  1. C141972E01
    Install the cowl top outer front panel sub-assembly with the 4 nuts, the 4 bolts and the clamp.

    Torque:
    Nut:
    85 N*m{ 867 kgf*cm , 63 ft.*lbf }
    Bolt:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }


16. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

  1. E135590E01
    Install the windshield wiper motor and link assembly with the 4 bolts.

    Torque:
    7.5 N*m{ 77 kgf*cm , 66 in.*lbf }

    NOTICE:
    Tighten the bolts in the order shown in the illustration.

  1. E135589
    Connect the connector.


17. INSTALL AIR CLEANER CASE SUB-ASSEMBLY (for LHD)

  1. A134905
    Install the air cleaner case with the 3 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Connect the hose clamp.


18. INSTALL AIR CLEANER CAP SUB-ASSEMBLY (for LHD)
  1. Install the air cleaner filter element onto the air cleaner case.

  1. A135670
    Insert the hinges. Install the air cleaner cap sub-assembly with the 2 bolts.

  1. A236553E01
    Connect the No. 1 air cleaner hose to the throttle body and unfasten the No. 1 air cleaner hose clamp.

    NOTICE:
    1. Match each concave area concavity of the air cleaner hose with the bolt of the throttle body.
    2. Make sure that the hose clamp is at the correct angle.

  1. A146036
    Connect the No. 2 ventilation hose to the air cleaner hose.

  1. A135666E02
    Connect the purge line hose to the clamp (*1).

  1. Connect the 2 purge VSV vacuum hoses (*2).

  1. Connect the purge VSV connector (*3).

  1. Connect the mass air flow meter connector (*4).


19. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

20. BLEED CLUTCH PIPE LINE
  1. Fill the brake reservoir with brake fluid and bleed the clutch system.

    Torque:
    8.3 N*m{ 85 kgf*cm , 74 in.*lbf }


21. INSPECT BRAKE FLUID
  1. Check the brake fluid (Click here).

    HINT:
    1. Check for leakage in the brake system.
    2. Check for leakage in the clutch system.


22. INSPECT FLUID LEVEL IN RESERVOIR

  1. C144901E01
    Check the fluid level.
    If brake fluid level is low, check for leakage and inspect the disc brake pad. If necessary, refill the reservoir with brake fluid after repair and replacement.

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT3


23. INSPECT AND ADJUST CLUTCH PEDAL SUB-ASSEMBLY
Click here.
← INSTALLATION (Oct 2006 – May 2009)COMPONENTS (from Jun 2006) →