2006-2011 Camry Aurion · Service Manual BODY

INSTALLATION

Removal / installation · Vehicles built Jun 2006 – Sep 2006

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009


1. INSTALL SLIDING ROOF WEATHERSTRIP

  1. Install the sliding roof weatherstrip as follows:

    1. Position the joint of the weatherstrip at the rear center.

    2. Align the marks on the weatherstrip with the middle marks at the corners of the sliding roof panel and install the weatherstrip.

    3. Install the lip of the weatherstrip firmly.

      B139674E01


2. INSTALL SLIDING ROOF HOUSING SUB-ASSEMBLY

  1. Install the sliding roof housing sub-assembly with the 4 bolts and 8 nuts.

    B152846

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Connect the 4 sliding roof drain hoses.


3. INSTALL SLIDING ROOF GLASS SUB-ASSEMBLY

  1. Using a T25 "TORX" driver, temporarily install the sliding roof glass sub-assembly with the 4 screws.

    B132109

  1. B132111E01
    Perform a level check.

    1. Check the difference in level "a", between the roof panel and the upper surface of the weatherstrip, when the sliding roof glass is fully closed.

      Standard:
      Area
      Measurement
      A - A
      0 + 1.0 mm (0 + 0.039 in.)
      0 - 2.0 mm (0 - 0.079 in.)
      B - B
      0 + 2.0 mm (0 + 0.079 in.)
      0 - 1.0 mm (0 - 0.039 in.)
      C - C
      0 + 1.5 mm (0 + 0.059 in.)
      0 - 1.5 mm (0 - 0.059 in.)
      D - D
      0 + 1.5 mm (0 + 0.059 in.)
      0 - 1.0 mm (0 - 0.039 in.)

      HINT:
      "+" represents the condition that the glass is above the panel level. "-" represents the condition that the glass is below the panel level.

  1. B132112E01
    Perform a gap check.

    1. Check the gap between the roof panel and roof glass.

      NOTICE:
      The gap must be even all around.

  1. After adjusting the sliding roof glass, using a T25 "TORX" driver, install the sliding roof glass sub-assembly with the 4 screws.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }


4. INSPECT FOR WATER LEAK
  1. After adjusting the sliding roof glass sub-assembly, check for water leaks.

  1. If there are any leaks, readjust the sliding roof glass sub-assembly.


5. INSTALL SLIDING ROOF SIDE GARNISH LH

  1. B132108
    Engage the 6 claws and install the sliding roof side garnish LH.


6. INSTALL SLIDING ROOF SIDE GARNISH RH

HINT:
Use the same procedure for the RH side and the LH side.


7. INSTALL CURTAIN SHIELD AIRBAG ASSEMBLY LH

8. INSTALL CURTAIN SHIELD AIRBAG ASSEMBLY RH

HINT:
Use the same procedure for the RH side and the LH side.


9. INSTALL ROOF HEADLINING ASSEMBLY

  1. B149220
    Pull the roof headlining assembly into the vehicle through the rear left door.

  1. Engage the hook, 4 clips, and 2 fasteners.

  1. Connect the sliding roof drive gear connector.

  1. Connect the antenna cord sub-assembly connector and engage the clamp to the rear pillar RH.

  1. Connect the antenna cord sub-assembly connector and engage each clamp to the front pillar RH.

  1. Install the radio setting condenser to the front pillar RH with the bolt.

  1. Connect the No. 1 roof wire connector and engage each clamp to the front pillar LH.

    B149212E01


10. INSTALL SUN ROOF OPENING TRIM MOULDING

  1. B147634E01
    Align the paint mark on the inner surface of the opening trim moulding with the notch of the roof headlining, and install the sun roof opening trim moulding so that the joining point of the opening trim is on the left side of the vehicle as shown in the illustration.

    NOTICE:
    After installation, check that the corners fit correctly.


11. INSTALL SPOT LIGHT ASSEMBLY

  1. B132096
    Push the light bulb holder in the direction indicated by the arrow in the illustration to engage the claw.

  1. Engage the 4 claws.

  1. B132094
    Engage the 6 claws and install the spot light assembly.


12. INSTALL FRONT ASSIST GRIP SUB-ASSEMBLY (for Driver Side)

  1. with Assist Grip:

    1. B132101
      Assemble the front assist grip sub-assembly as shown in the illustration.

    2. B132102
      Install the front assist grip sub-assembly.


13. INSTALL FRONT ASSIST GRIP SUB-ASSEMBLY (for Front Passenger Side)

  1. B147412
    Assemble the front assist grip sub-assembly as shown in the illustration.

  1. B147408
    Install the front assist grip sub-assembly.


14. INSTALL REAR ASSIST GRIP SUB-ASSEMBLY

HINT:
Use the same procedure for the rear side and front side.


15. INSTALL VISOR HOLDER
  1. Engage the 2 claws.

  1. Push in the visor holder as shown in the illustration.

    B149236

    HINT:
    Use the same procedure for the RH side and the LH side.


16. INSTALL VISOR ASSEMBLY LH

  1. B139565
    Engage the 2 clips and install the visor assembly LH.

  1. B139566
    Engage the 4 claws and install the visor bracket cover.


17. INSTALL VISOR ASSEMBLY RH

HINT:
Use the same procedure for the RH side and the LH side.


18. INSTALL ROOF CONSOLE BOX ASSEMBLY

  1. B132065
    Connect the connectors.

  1. Engage the 2 claws and 2 clips, and then install the roof console box assembly.


19. INSTALL RAIN SENSOR COVER (w/ Rain Sensor)

  1. E128843
    Install the rain sensor cover.


20. INSTALL FRONT PILLAR GARNISH LH (w/o Curtain Shield Airbag)

  1. B149232E01
    Install a new clip <A> on the front pillar garnish LH.

  1. Engage the 2 claws and 2 clips, then install the front pillar garnish LH.


21. INSTALL FRONT PILLAR GARNISH LH (w/ Curtain Shield Airbag)

  1. B154714E01
    Remove the protective cover.

  1. B149232E01
    Install a new clip <A> on the front pillar garnish LH.

  1. Engage the 2 claws and 2 clips, then install the front pillar garnish LH.


22. INSTALL FRONT PILLAR GARNISH RH (w/o Curtain Shield Airbag)

  1. B149231E01
    Install a new clip <A> on the front pillar garnish RH.

  1. Engage the 2 claws and 2 clips, then install the front pillar garnish RH.


23. INSTALL FRONT PILLAR GARNISH RH (w/ Curtain Shield Airbag)

  1. B154715E01
    Remove the protective cover.

  1. B149231E01
    Install a new clip <A> on the front pillar garnish RH.

  1. Engage the 2 claws and 2 clips, then install the front pillar garnish RH.


24. INSTALL ROOF SIDE INNER GARNISH LH

  1. B132063
    Engage the 5 clips and 2 claws, then install the roof side inner garnish LH.


25. INSTALL ROOF SIDE INNER GARNISH RH

HINT:
Use the same procedure for the RH side and the LH side.


26. INSTALL UPPER CENTER PILLAR GARNISH LH

  1. B132060
    Engage the clip.

  1. Install the upper center pillar garnish LH with the bolt.


27. INSTALL LOWER CENTER PILLAR GARNISH LH

  1. B132058
    Engage the 2 claws and 2 clips, then install the lower center pillar garnish LH.


28. CONNECT FRONT SEAT OUTER BELT ASSEMBLY LH

  1. B131996
    Install the floor end of the front seat outer belt assembly LH with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }


29. INSTALL LAP BELT OUTER ANCHOR COVER (for LH Side)

  1. B131995
    Engage the 3 claws and install the lap belt outer anchor cover.


30. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

  1. B132081E01
    Install the front door opening trim weatherstrip LH as shown in the illustration.

    NOTICE:
    After installation, check that the corners fit correctly.


31. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH

  1. B132116E01
    Engage the 2 clips.

  1. Install the cowl side trim sub-assembly LH with the cowl side trim clip.


32. INSTALL FRONT DOOR SCUFF PLATE LH

  1. B132067
    Engage the 7 claws and 3 clips, then install the front door scuff plate LH.


33. INSTALL UPPER CENTER PILLAR GARNISH RH

HINT:
Use the same procedure for the RH side and the LH side.


34. INSTALL LOWER CENTER PILLAR GARNISH RH

HINT:
Use the same procedure for the RH side and the LH side.


35. CONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

HINT:
Use the same procedure for the RH side and the LH side.


36. INSTALL LAP BELT OUTER ANCHOR COVER (for RH Side)

HINT:
Use the same procedure for the RH side and the LH side.


37. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

  1. B132083E01
    Install the front door opening trim weatherstrip RH as shown in the illustration.

    NOTICE:
    After installation, check that the corners fit correctly.


38. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:
Use the same procedure for the RH side and the LH side.


39. INSTALL FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedure for the RH side and the LH side.


40. INSTALL REAR DOOR INNER GLASS WEATHERSTRIP LH

  1. B149019
    Engage the 3 claws to install the rear door inner glass weatherstrip.


41. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY LH

  1. B149020
    Engage the claw to install the No. 1 door scuff plate clamp.

  1. Connect each connector.

  1. B136452
    Engage the rear door trim board with the 4 clips of the rear door inner glass weatherstrip.

  1. B136451
    Engage the 7 clips to install the rear door trim board to the rear door panel.

  1. Install the 3 screws.


42. INSTALL REAR ASH RECEPTACLE ASSEMBLY LH (w/ Ashtray)

  1. B136442
    Install the rear ash receptacle assembly.


43. INSTALL DOOR ASSIST GRIP COVER LH

  1. B136448
    Engage the 6 claws and install the door assist grip cover.


44. INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG LH

  1. B136444
    Engage the 3 claws to install the rear door inside handle bezel plug.


45. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

  1. B132080E02
    Install the rear door opening trim weatherstrip LH as shown in the illustration.

    NOTICE:
    After installation, check that the corners fit correctly.


46. INSTALL REAR DOOR SCUFF PLATE LH

  1. B132068
    Engage the 5 claws and 2 clips, then install the rear door scuff plate LH.


47. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH

  1. B132082E01
    Install the rear door opening trim weatherstrip RH as shown in the illustration.

    NOTICE:
    After installation, check that the corners fit correctly.


48. INSTALL REAR DOOR SCUFF PLATE RH

HINT:
Use the same procedure for the RH side and the LH side.


49. INSTALL REAR SIDE SEATBACK ASSEMBLY LH (for Fold Down Seat Type)

  1. B136561
    Install the rear side seatback assembly with the bolt.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }


50. INSTALL REAR SIDE SEATBACK ASSEMBLY RH (for Fold Down Seat Type)

HINT:
Use the same procedure for the RH side and the LH side.


51. INSTALL SEPARATE TYPE REAR SEATBACK ASSEMBLY LH (for Fold Down Seat Type)

  1. B136539
    Install the separate type rear seatback assembly with the 2 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }


52. INSTALL SEPARATE TYPE REAR SEATBACK ASSEMBLY RH (for Fold Down Seat Type)

  1. B134700
    Install the separate type rear seatback assembly with the 2 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }


53. INSTALL REAR SEATBACK ASSEMBLY (for Fixed Seat Type)

  1. B136577
    Place the seatback in the cabin.

    NOTICE:
    Be careful not to damage the vehicle body.

  1. Install the rear seatback assembly with the 4 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

  1. B136576
    Pass the 3 seat belts through and close the cap of the 2 rear seat shoulder belt guides.

  1. Install the floor anchor part with the bolt.


54. INSTALL REAR CENTER SEAT HEADREST ASSEMBLY (w/ Center Armrest)

55. INSTALL REAR SEAT HEADREST ASSEMBLY

56. INSTALL REAR SEAT CUSHION ASSEMBLY (for Fixed Seat Type)

  1. B140589E01
    Attach the 2 front hooks of the seat cushion to the vehicle body.

  1. Confirm that the seat cushion is firmly installed.

    NOTICE:
    When installing the seat cushion, make sure the seat belt buckle is not under the seat cushion.


57. INSTALL REAR SEAT CUSHION ASSEMBLY (for Fold Down Seat Type)

  1. B140584E01
    Attach the front hooks of the bench type rear seat cushion assembly to the vehicle body.

  1. Confirm that the seat cushion is firmly installed.

    NOTICE:
    When installing the bench type rear seat cushion assembly, make sure that the seat belt buckle is not under the bench type rear seat cushion assembly.


58. INSTALL FRONT SEAT ASSEMBLY LH (for Power Seat)
  1. Place the seat in the cabin.

  1. Connect the connectors under the seat.

  1. Connect the cable to the negative (-) battery terminal.

  1. Move the front seat assembly to the rearmost position by operating the slide and vertical power seat switch knob.

  1. B149590
    Temporarily install the front side of the front seat assembly with the 2 bolts.

  1. Move the front seat assembly fully forward by operating the slide and vertical power seat switch knob.

  1. B139102
    Temporarily install the rear side of the front seat assembly with the 2 bolts.

  1. Move the front seat assembly to the rearmost position by operating the slide and vertical power seat switch knob.

  1. Fully tighten the 2 bolts on the front side of the front seat assembly in the order of the inner side bolt and then the outer side bolt.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

  1. Move the front seat assembly fully forward by operating the slide and vertical power seat switch knob.

  1. Fully tighten the 2 bolts on the rear side of the front seat assembly in the order of the inner side bolt and then the outer side bolt.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }


59. INSTALL INNER SEAT TRACK BRACKET COVER LH (for Power Seat)

  1. B149588E01
    Slide the inner seat track bracket cover along the seat rail toward the front of the vehicle. Engage claw A to the seat rail.

  1. Push the inner seat track bracket cover to engage claw B.


60. INSTALL OUTER SEAT TRACK BRACKET COVER LH (for Power Seat)

  1. B149587E01
    Slide the outer seat track bracket cover along the seat rail toward the front of the vehicle. Engage claw A to the seat rail.

  1. Push the seat track cover to engage claw B.


61. INSTALL FRONT SEAT HEADREST ASSEMBLY (for Power Seat)

62. INSTALL FRONT SEAT ASSEMBLY LH (for Manual Seat)
  1. Place the front seat assembly in the vehicle and align the adjuster pin with the hole on the vehicle side.

  1. Connect the connector and clamp.

  1. Move the front seat assembly to the rearmost position by operating the slide handle.

    NOTICE:
    Check that the seat is locked.

  1. B139101
    Temporarily install the front seat track bracket with the 2 bolts.

  1. Move the front seat assembly fully forward by operating the slide handle.

    NOTICE:
    Check that the seat is locked.

  1. B139102
    Temporarily install the rear seat track bracket with the 2 bolts.

  1. Move the front seat assembly to the rearmost position by operating the slide handle.

    NOTICE:
    Check that the seat is locked.

  1. Fully tighten the 2 bolts on the front seat track bracket in the order of the inner side bolt and then the outer side bolt.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

  1. Move the front seat assembly fully forward by operating the slide handle.

    NOTICE:
    Check that the seat is locked.

  1. Fully tighten the 2 bolts on the rear seat track bracket in the order of the inner side bolt and then the outer side bolt.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }


63. INSTALL INNER SEAT TRACK BRACKET COVER LH (for Manual Seat)

  1. B149588E01
    Slide the inner seat track bracket cover along the seat rail toward the front of the vehicle. Engage claw A to the seat rail.

  1. Push the inner seat track bracket cover inner to engage claw B.


64. INSTALL OUTER SEAT TRACK BRACKET COVER LH (for Manual Seat)

  1. B149587E01
    Slide the outer seat track bracket cover along the seat rail toward the front of the vehicle. Engage claw A to the seat rail.

  1. Push the outer seat track bracket cover to engage claw B.


65. INSTALL FRONT SEAT HEADREST ASSEMBLY (for Manual Seat)

66. INSTALL FRONT SEAT ASSEMBLY RH (for Power Seat)

HINT:
Use the same procedure for the RH side and the LH side.


67. INSTALL INNER SEAT TRACK BRACKET COVER RH (for Power Seat)

HINT:
Use the same procedure for the RH side and the LH side.


68. INSTALL OUTER SEAT TRACK BRACKET COVER RH (for Power Seat)

HINT:
Use the same procedure for the RH side and the LH side.


69. INSTALL FRONT SEAT HEADREST ASSEMBLY (for Power Seat)

70. INSTALL FRONT SEAT ASSEMBLY RH (for Manual Seat)
  1. Place the front passenger's seat assembly in the vehicle and align the adjuster pin with the hole on the vehicle side.

  1. Connect the connectors and clamp.

  1. Move the front passenger's seat assembly to the rearmost position by operating the slide handle.

    NOTICE:
    Check that the seat is locked.

  1. B147667
    Temporarily install the front seat track bracket with the 2 bolts.

  1. Move the front passenger's seat assembly fully forward by operating the slide handle.

    NOTICE:
    Check that the seat is locked.

  1. B147668
    Temporarily install the rear seat track bracket with the 2 bolts.

  1. Move the front passenger's seat assembly to the rearmost position by operating the slide handle.

    NOTICE:
    Check that the seat is locked.

  1. Fully tighten the 2 bolts on the front seat track bracket in the order of the inner side bolt and then the outer side bolt.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

  1. Move the front passenger's seat assembly fully forward by operating the slide handle.

    NOTICE:
    Check that the seat is locked.

  1. Fully tighten the 2 bolts on the rear seat track bracket in the order of the inner side bolt and then the outer side bolt.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }


71. INSTALL INNER SEAT TRACK BRACKET COVER RH (for Manual Seat)

  1. B147666E01
    Slide the inner seat track bracket cover along the seat rail toward the front of the vehicle. Engage claw A to the seat rail.

  1. Push the inner seat track bracket cover to engage claw B.


72. INSTALL OUTER SEAT TRACK BRACKET COVER RH (for Manual Seat)

  1. B147665E01
    Slide the outer seat track bracket cover along the seat rail toward the front of the vehicle. Engage claw A to the seat rail.

  1. Push the outer seat track bracket cover to engage claw B.


73. INSTALL FRONT SEAT HEADREST ASSEMBLY (for Manual Seat)

74. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (for Manual Seat)

75. INSPECT SRS WARNING LIGHT
(Click here)

76. RESET SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY
(Click here)

77. INSPECT SLIDING ROOF SYSTEM
(Click here)

78. INSPECT FRONT SEAT ASSEMBLY (for Power Seat)
  1. Inspect the power seat operation.


79. INSPECT FRONT SEAT ADJUSTER ASSEMBLY (for Manual Seat)
← REASSEMBLY (from Jun 2006)INSTALLATION (Oct 2006 – May 2009) →