2006-2011 Camry Aurion · Service Manual BRAKE

C0278/11 Open or Short Circuit in ABS Solenoid Relay Circuit

Diagnostic trouble codes · Vehicles built Jun 2006 – Sep 2006

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

The ABS solenoid relay supplies power to the ABS solenoid.
The solenoid relay is turned on 1.5 seconds after the ignition switch is turned ON, and is turned off if an open or short in the solenoid is detected by self diagnosis performed when the vehicle starts running.
The ABS solenoid relay is housed in the skid control ECU in the brake actuator assembly.

HINT:
If a speed signal of 6 km/h (4 mph) or more is input to the skid control ECU, with the ignition switch ON and the stop light switch off, the skid control ECU performs self diagnosis of the motor and solenoid circuits.

DTC No.
DTC Detection Condition
Trouble Area
C0278/11
When either of the following is detected:
  1. When the relay is ON, the voltage is less than IG terminal voltage x 0.8 V for 0.5 seconds.
  2. When the relay is OFF, the voltage is out of range (IG terminal voltage x 0.1 to IG terminal voltage x 0.8).
  1. ABS No. 2 fuse (Fusible link)
  2. Brake actuator assembly (solenoid relay)
  3. Solenoid relay circuit

WIRING DIAGRAM

C144435E08

INSPECTION PROCEDURE

HINT:
  1. When C1241/41 is output together with C0278/11, inspect and repair the trouble areas indicated by C1241/41 (Click here).
  2. Check the condition of each related circuit connector before troubleshooting (Click here).


1. INSPECT FUSIBLE LINK (ABS NO. 2 FUSE)

  1. C136500E05
    Remove the fusible link from the engine room R/B.

  1. Check if the fusible link is melted.

    OK:
    The fusible link is not melted.

  1. Install the fusible link to the engine room R/B with the nut.

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



NG
REPLACE FUSIBLE LINK
OK


2. INSPECT SKID CONTROL ECU (+BS TERMINAL VOLTAGE)

  1. C136493E14
    Disconnect the skid control ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    A26-3 (+BS) - Body ground
    Always
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (+BS CIRCUIT)
OK


3. INSPECT SKID CONTROL ECU (GND TERMINAL CONTINUITY)

  1. C136493E13
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    A26-4 (GND1) - Body ground
    Below 1 Ω
    A26-1 (GND2) - Body ground
    Below 1 Ω

  1. Connect the connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)
OK


4. RECONFIRM DTC

HINT:
This code is detected when a problem is identified in the brake actuator assembly.
The solenoid circuit is located in the brake actuator assembly.
Therefore, solenoid circuit inspection and solenoid unit inspection cannot be performed. Be sure to check if the DTC is output before replacing the brake actuator assembly.

  1. Clear the DTCs (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 20 km/h (12 mph) or more for 30 seconds or more.

  1. Check if the same DTC is recorded (Click here).

    HINT:
    Reinstall the sensors, connectors, etc. and restore the vehicle to its prior condition before rechecking for DTCs.


    Result:
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B

    HINT:
    1. If the normal system code is output (the trouble code is not output), slightly jiggle the connectors, wire harnesses, and fuses of the brake actuator assembly. Make sure that no DTCs are output.
    2. If any DTCs are output while jiggling a connector or wire harness of the brake actuator (skid control ECU), inspect and repair the connector or wire harness.
    3. It is suspected that the DTCs were output due to a bad connection of the connector terminal.



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)


← C0273/13 Open or Short Circuit in ABS Motor Relay Circuit (from Jun 2009)C0278/11 Open or Short Circuit in ABS Solenoid Relay Circuit (Oct 2006 – May 2009) →